Intelbras IVP 7001 MW PET User manual

User manual
IVP 7001 MW PET

IVP 7001 MW PET
Passive infrared sensor
Congratulations, you have just purchased a product with Intelbras quality and safety.
The IVP 7001 MW PET passive infrared sensor has triple technology, which combines microwave de-
tection with detection by passive infrared rays and immunity to animals up to 20kg. Advanced signal
analysis technology prevents false triggering indoors.

Care and safety
» Follow all instructions in the manual for assembling and installing the product.
» This sensor is intended for indoor environments.
» LGPD - General Law for the Protection of Personal Data: Intelbras does not access, transfer, capture, or perform any other
type of treatment of personal data from this product.
» Do not touch the surface of the infrared (PIR) sensor. If necessary, use a soft cloth for cleaning.
» The sensor must be installed where a possible intruder is easily detected, that is, where a person performs movements
transverse to the sensor’s detection beams when entering the environment. The optimal installation height is 2.2 m,
depending on the installation environment, the sensor can be installed from 2 to 2.4 m in height.
6m
6m
0m
Top view
» Do not place objects in front of the sensor. Keep the detection area free of objects that move or block the scan. Do not
exceed the maximum sensor installation height (2.4 m).
» Do not use the sensor in areas with sudden changes in temperature, near air conditioners, heaters, cooling fans and
ovens.

» It is important to note that the Pet function is designed for crawling animals, so if the animal is not on the ground, but on
top of a bench, for example, it can be detected thus canceling the Pet function , as seen in the image below :
» Do not install the sensor facing glass doors or windows.
» Make sure the installation location is stable and free from ickering.
» For your security, test the product and systems at least once a week. This is necessary due to changes in environmental
conditions, electrical or electronic interruptions and violations. Take all necessary precautions for the security and pro-
tection of your property.
Scan (top view)
Detection range (side view)
Máx. 2,4
Mín. 2
2,2 m

Summary
1. Technical specications 6
2. Product 6
3. Characteristics 7
4. Installation 7
5. Troubleshooting 11
6. Approval 11
Warranty term 12

6
1. Technical specications
Operating voltage 9-16 Vdc
Operating Current ≤ 40 mA (12 Vdc)
Detection Angle 90°
Detection range¹ 12 × 12 m ± 20%
Detection method MW and PIR
AND and OR function Yes
Anti-camouage Yes (OR function)
Sensor element Low noise PIR
MW antenna GaAs FET
MW Frequency 10.525 GHz
Immunity to animals Up to 20 kg
Detection pulse (P. COUNT) 1P, 2P, 3P
Recommended installation height 2.2m
Installation height range 2.0 to 2.4 m
Alarm output NF / NA selectable, 28 Vdc, 80 mA max
Tamper switch NF, 28 VDC and 100 mA max
LED indicators Green (PIR), Yellow (MW) and Red (Alarm)
Start Time 60s
Relay opening time 5s
Operating temperature -10 °C ~ +50 °C
Dimensions (W × H × D) 60 × 120 × 37 mm
¹ The sensor’s detection range can be inuenced by the environment.
2. Product
LEDs
Gabinete
frontal
Lente
Micro-ondas
Conectores
Parafuso de
xação da
placa
PIR
Tamper
Ajuste
MW
DIP
Switch
Suporte
Gabinete
traseiro
Lacre para
instalação
em quina
Lacre para
instalação
em parede
Lacre para
instalação
em parede
Lacre para
suporte
Lacres para
passagem
do o
Front cabinet
Wire seals
Wire seals
Rear cabinet
Lens
Seal for wall
installation
Plate xing
screw
Seal for wall
installation
Seal for
support
MW
setting
Microwave
Support

7
3. Characteristics
» Microcontrolled signal processing;
» Microwave (Doppler effect) + infrared;
» Adjustable microwave power;
» Automatic temperature compensation to reduce false alarms;
» Immunity to white light up to 10,000 lux;
» Articulating bracket for attachment;
» High immunity to RFI / EMI - shield;
» Selectable relay output NA and NF (Normally open and normally closed);
» Infrared sensitivity (PIR) adjustable;
» Immunity to crawling animals weighing less than 20 kg;
» Anti-tamper protection (tamper switch).
4. Installation
Before starting the installation, it is necessary to dene the height at which the sensor will be positioned, which can vary
from 2 to 2.4 m;
» Do not install sensors that have microwave technology close to each other, as there may be interference between them;
» Adjustment of the sensitivity of the PIR (P. Count) and the microwave must be made according to each environment.
» For environments that have the circulation of pets, we recommend that you use the following conguration for the
correct operation of the PET function:
PET function
Installation height Between 2.3 and 2.4 m
AND / OR function AND
PIR sensitivity 3P
Note: if the sensor is congured at maximum sensitivity (1P), unwanted triggering may occur with the presence of pets.
To attach the sensor follow the steps described below:
1. Open the sensor, as shown below:
12
3

8
2. Remove the card to perform the installation:
Gire o parafuso
no sentido
anti-horário
Deslize a placa
para cima
para removê-la
Turn the screw
counterclockwise
Slide the card up
to remove it
3. For installation directly or in a wall corner, break the seals indicated for the holes in the rear attaching cover:
Lacres para
instalação
em parede
Lacres para
instalação
em quina
Seal for wall
installation Seal for corner
installation
4. Installation without using the articulator:
Attention: if the mounting bracket is inclined with respect to the ground, the characteristics of the PET function
will change. This support only has horizontal movement, and vertical movement is not possible.
» With the help of a wrench, break the screw passage seal located on the rear cover and connect the articulator parts
and the screw on the rear of the cabinet, as shown below:
Obs.: As setas indicativas
nas peças devem ficar para cima
conforme imagem.
Note: the indicative arrows on the parts must
be upwards as shown in the images.

9
» For installation directly on the wall, drill the holes in the positions indicated on the base of the articulator. For installation
in the corner of the wall, it is not possible to use the bracket. Before screwing the articulator in position, drill the cable
passage seal on the base and pass the cable as shown in the images:
5. Fit the board back into the cabinet as shown below:
Gire o parafuso
no sentido
horário
Insira a placa e
deslize-a par
a
baixo
Insert the card and
slide it down Turn the screw
clockwise
6. Connect the cables following the terminal indications. When powered on, the sensor LEDs will ash for 60s. This time is
necessary to stabilize the amplication circuit of the PIR sensor and the microwave.
ALARME
+12VdcGND TAMPER
12
3456

10
7. Perform the conguration on the sensor:
» The LED jumper is used to control the LED indication without interfering with the detector. With the switch in the On
position, the LEDs are enabled to function normally. With the switch in the Off position, the LEDs are disabled, that is,
they do not light up. Factory default: LEDs On.
LED
Dip Position Condition
2On LED on.
Off LED off
» P.COUNT: controls the pulse count of the PIR sensor to trigger the alarm. This adjustment has three selectable levels,
according to the table below. Choose the conguration accordingly according to the environment in which the sensor
will be installed. Factory Default: 1P
Note: Off-Off conguration must not be used.
P. COUNT
Dip Position Condition
4 5
On - On 1P - Maximum sensitivity
On - Off 2P - Intermediate sensitivity
Off - On 3P - Minimum sensitivity (EMI and RFI)
Greater immunity to false triggering
» AND / OR function: controls the sensor detection mode. In the AND position, both the PIR and the microwave need
to detect the presence of an intruder simultaneously to trigger the sensor. In the OR position, the sensor will trigger if
the PIR or microwave detects it. Factory Default: AND
AND / OR
Dip Position Condition
1On AND - PIR and microwave detection for triggering the alarm
Off OR - PIR or microwave detection for triggering the alarm
» The sensor also has a trimpot (MW setting) to adjust the microwave sensitivity. Turning the trimpot clockwise will
increase the sensitivity, turning it counterclockwise will make the microwave less sensitive. Factory default: MAX
(maximum sensitivity).
Caution: the microwave setting must be at the sensitivity that is able to provide detection only in the protected
area to avoid undue triggering.
Microwaves
Position Condition
MIN. Minimum detection range
MAX Maximum detection range
» Relay: controls the state of the relay contact. In the Off position, the contact is normally closed. In the On position, the
contact is normally open. Factory default: NF (normally closed).
Relay
Dip Position Condition
3On NF- Normally closed
Off NA- Normally open