Intelbras XAS Smart User manual

User manual
XAS Smart
XAS Smart Black
English

XAS Smart and XAS Smart Black
Sensor
Congratulations, you have just purchased a product with Intelbras quality and safety.
The XAS Smart / XAS Smart Black wireless aperture sensor was developed by Intelbras
with 100% digital technology. The sensor is mounted on SMD components and can be
installed in most products that work at the same frequency and modulation available
on the market. It works in FSK or OOK modulation and has a low battery sensor.

Care and safety
» Follow all instructions in the manual for assembling and installing the product.
» LGPD –Data processing by Intelbras: Intelbras does not access, transfer, capture or perform
any type of processing of personal data from this product.
» This product is intended for indoor and semi-open environments.
» Respect the GAP distance (distance between the sensor and the magnet).
» Confirm that the installation location is stable and appropriate.
» Wireless communication technology, when exposed to environments with high power radia-
tion, may suffer interference and have its performance impaired, for example: locations close
to TV towers, AM/FM radio stations, amateur radio stations, etc.
» Do not expose the XAS Smart and Xas Smart Black magnetic sensors to direct sunlight, rain
and moisture.
» For your safety, test the product and systems at least once a week. This is necessary due to
changing environmental conditions, electrical or electronic interruptions, and tampering. Take
all necessary precautions for the safety and security of your property.

Summary
1. Technical specifications 5
2. Characteristics 5
3. Product 6
4. Sensor aperture 6
5. Enrolling the XAS Smart and XAS Smart Black sensor 7
6. XAS Smart and XAS Smart Black sensor supervision setting 8
7. Installation 9
8. Battery 11
9. Test 11
10. Homologation 11
Warranty term 12

1. Technical specifications
Operating voltage Battery 3 V Lithium, model CR2032
Operating current 900 nA
Trigger indication Green LED
RF range 100 meters without hurdles
Transmission frequency 433.92 MHz
Detection Magnetic Field SMD Sensor
Modulation OOK / FSK
Baud rate OOK / FSK 2 KBps (open source)
Anti jamming Against external interference
Installation environment Internal and Semi-open
Opening gap 37 mm ± 10%
Closing gap 27 mm ± 10%
Operating Temperature -10 °C to 50 °C
Sensor: 37 × 46 × 11 mm
Dimensions (W × H × D)
Magnet: 11 × 31 × 9 mm
Gross weight 0,06 Kg
Net weight 0,04 Kg
2. Characteristics
» Supervised (FSK) or unsupervised (OOK);
» Long-lasting lithium battery;
» SMD magnetic field sensor;
» Transmission frequency 433.92 MHz.
5

5
4
4
4
4
7
3
Sensor
Magnet
Lock
3. Product
1
2 6 8
1. Sensor cover
2. Light conductor (LED)
3. Sensor base
4. Screw hole for fixing
5. Magnet cover
6. Magnet base
7. Battery contact
8. Jumper OOK/FSK
4. Sensor aperture
To access the XAS Smart and XAS Smart Black board to change the battery or change the
FSK/OOK supervision, just remove the cover through the latch, it is not necessary to use
tools.This way the plate will be exposed and ready for handling.
6

CR2032
3V
Remove the board, then insert the battery (model CR2032), respecting the polarity.
5. Enrolling the XAS Smart and XAS Smart
Black sensor
To register the XAS Smart and XAS Smart Black sensor code in the control panel,
follow the procedure below:
Insert the LITHIUM 3 Vdc battery - CR 2032, then type the command to register the
wireless device in the alarm center that will be used (Check the procedure in the
alarm center manual). Then perform a shot moving the magnet away from the sensor,
if the sensor is in a door for example, just open it observing if the LED will light up.
If the LED lights up, it indicates that there was a trip or transmission occurred, if the
LED does not light up, check the battery.
» Low battery sensor: the XAS Smart/XAS Smart Black has a battery level meter,
which measures the voltage and notifies you of the best time to change it, if the
sensor flashes the LED quickly in the opening, it indicates a low battery level. If
the alarm center is Intelbras, the sensor low battery warning will be indicated on
the product panel. The sensor sends low battery warning in both OOK and FSK
modulation.
7

OOK/F SK
OOK/F SK
6. XAS Smart and XAS Smart Black sensor
supervision setting
The XAS Smart/XAS Smart Black sensor allows you to select between supervised
(FSK) and unsupervised (OOK) modes. To switch between supervision modes, simply
remove the battery from the sensor, open the OOK/FSK jumper indicated on the bo-
ard (and then replace the battery), after which the sensor will operate in supervised
mode (FSK). Changing from supervised mode (FSK) to non-supervised mode (OOK) is
also simple, just remove the battery from the sensor, close the OOK/FSK jumper ter-
minals again and replace the battery, after which the sensor will return to operating
mode. unattended mode (OOK). Factory default: unsupervised (OOK)
In FSK modulation, the sensor transmits opening and closing and periodically super-
vises the sensor.
With Jumper OOK
No Jumper FSK
8

GAP
7. Installation
The XAS Smart / XAS Smart Black sensor can be attached using double-sided tape
or a screw. If the option with double-sided tape is chosen, clean the surface that will
be in direct contact with the tape and then stick it to the base of the product. If you
are going to use screws, just open the sensor and use the holes for passing the screw
located at the base of the product, as shown in the following figure.
Important: check if the GAP distance (distance between the sensor and the mag-
net) is within the specification, to avoid unwanted triggering in case of any vibration
in the structure where the sensor is installed.
Note: the type of surface where the sensor is installed may influence the distance
from the GAP.
» Opening GAP: 37 mm ±10%
» Closing GAP: 27 mm ±10%.
9

Aperte
para
travar
Figura 01
Figura 02
Pino
Aperte
para
travar
Press to
lock
To close the sensor, check the pin located on the base, it must be positioned on the
same side as the battery, after positioning the base, just press it for locking, there is only
one way to close the sensor, check image 01 To close the magnet, just position the base
and press it, image 02.
Figure 2
The sensor must be installed according to the images below, with the magnet aligned
with the sensor body and with the smallest possible distance between them, so that
the magnet is in contact with the magnetic field sensor.
Note: for closing and opening the SMD magnetic field sensor, the distances from the
GAP must be respected.
10
Pin
Press to
lock
Figure 1