Intelbras IVP 8000 Pet User manual

User guide
IVP 8000 Pet
English

IVP 8000 Pet
Passive infrared sensor
Congratulations, you have just purchased a product with Intelbras quality and safety.
The passive infrared motion sensor IVP 8000 Pet has an intelligent detection algorithm that, com-
bined with automatic temperature compensation, prevents false triggers. Allows quick and simple
conguration remotely through software or application. Immune to pets, it allows installation indoors
with pets weighing up to 20 kg. Increased security against tampering through front and rear tamper
switches. Totally wireless system that facilitates and reduces installation costs.

Care and safety
»LGPD – Data processing by Intelbras: Intelbras does not access, transfer, capture or process any
kind of personal data from this product.
»Follow all instructions in the manual for assembling and installing the product;
»Fix the sensor on stable surfaces, where there are no vibrations;
»This sensor is intended for an indoor environment;
Externo
Interno Semiaberto
ExternalInternal Semi-open
»Do not use the sensor in areas with sudden changes in temperature, such as near air conditioners
and heaters, fans, refrigerators and ovens. Do not expose the sensor to direct or reected sunlight;
»Do not install the sensor facing windows and glass doors;
»Wireless communication technology, when exposed to environments with high power irradiation,
may suffer interference and have its performance impaired. Example: locations close to TV towers,
AM/FM radio stations, amateur radio stations, routers, etc;
»Do not touch the surface of the infrared (PIR) sensor. If necessary, use a cleaning cloth;
»The recommended maximum installation height is 2.20 m, do not exceed it;
»Do not place objects in front of the sensor. To ensure the detection area, avoid curtains, screens,
screens, or any object that may interfere with its coverage area;
»The sensor must be installed where a possible intruder can be easily detected, that is, where it
makes transverse movements to the detection beams (see the gure below);
X

»The Pet function is intended for crawling animals weighing up to 20 kg. If the animal is on top of a
bench, for example, the Pet function can be canceled.
Obs.: before starting the installation, it is necessary to dene the height at which the sensor will be
positioned, which can vary from 1.8 to 2.2 m. If the sensor is installed at a height of less than 1.8 m or
is tilted downwards, the Pet function will be compromised.
Scan
0 2 4 6 8 10 12 (m)
8 (m)
6
4
2
0
2
4
6
8
Upper view
Detection range
1.2 4 6 8 10 12m
1.8 ~2.20m
Side view

Summary
1. Technical specications 6
2. Characteristics 6
3. Product 7
4. Sensor aperture 7
5. Sensor stabilization 8
6. Registering the IVP 8000 Pet sensor 8
6.1. Sensors with rmware version equal to or greater than 3.0.0..............................8
6.2. Sensors with rmware version less than 3.0.0 ..........................................8
7. Deleting the sensor record 8
8. Identifying the best location for installation 9
9. Installation 9
10. Trial period 10
11. Test 11
12. Conguring the IVP 8000 Pet sensor 11
12.1. Conguring sensors with rmware version equal to or greater than 3.0.0 .................11
12.2. Information about sensor adjustments ..............................................12
12.3. Information about LED operation and mode of operation...............................12
12.4. Conguring the sensor through the app .............................................13
12.5. Conguring sensors with rmware version less than 3.0.0..............................14
12.6. Conguring the sensor through the app .............................................15
13. Battery 16
14. Battery replacement 16
15. Homologation 16
Warranty term 17

6
1. Technical specications
Operating voltage 3 Vdc
Operating current 26 mA
Current at rest 6uA
Frequency range 915 MHz to 928 MHz
Modulation DSSS BPSK 40 Kbps
Maximum transmission power 11 dBm
Battery LITHIUM CR123A 3 V
Detection angle 90°
Detection range 12 m
Detection method PIR
Animal immunity Up to 20 kg
Maximum startup time 60 seconds
Operating Temperature -10 °C ~ +50 °C
RF range 1000 meters no hurdles
Dimensions (W × H × D) 68 × 55 × 120 mm
2. Characteristics
»Automatic real-time temperature compensation.
»Intelligent algorithm that prevents false triggers;
»Verication of communication status through LED, keyboard and application;
»Wireless communication with range of up to 1000 meters with direct sight in open eld;
»Front and rear tamper switch (tamper switch);
»Supervised wireless communication;
»Encrypted transmission;
»Sensor conguration through applications;
»Immunity to crawling animals weighing less than 20 kg;
»Immunity to white light up to 10,000 lux;
»Ease of installation.

7
3. Product
IVP 8000
1
2
3
4
5
6
8
9
10
11
12
13
14
14
14
14
14
14
7
1. Antenna
2. Pir sensor
3. Front Tamper Wrench
4. Battery connector
5. LED status
6. Sync key
7. Blue LED (Trigger)
8. Front cover
9. Fresnel lens
10. Lower front cover
11. Basis
12. Back tamper switch
13. Bracket
14. Screw installation seal
4. Sensor aperture
To access the IVP 8000 Pet sensor board for registration, changing the battery or removing it from
the control panel, remove the lower front cover. See image below:

8
5. Sensor stabilization
After inserting the battery, the sensor goes into stabilization mode and the blue LED ashes for a
few seconds. When stabilization is complete, the blue LED will stop ashing.
6. Registering the IVP 8000 Pet sensor
The sensor registration can be performed through the AMT 8000 Desktop Programmer software,
remote AMT mobile application, keyboard commands and synchronization button on the alarm cen-
ter. Follow one of the options below for registration through the synchronization button on the con-
trol panel. In this type of registration, the address of the sensors follows the registration sequence,
Example: First sensor will be registered in zone 1, the second sensor in zone 2 and so on. For other
forms of registration, please consult the complete manual of the AMT 8000 control panel.
6.1. Sensors with rmware version equal to or greater than 3.0.0
1. Press the alarm control panel synchronization button;
2. LED 3 on the control unit stays on for 3 minutes, indicating that it is waiting for the sensor to re-
gister;
3. Insert the battery and wait for the sensor to stabilize;
4. Press the sensor synchronization switch;
5. The status LED will ash green indicating the correct registration. If it ashes red, the registration
was not carried out and the procedure must be repeated.
6.2. Sensors with rmware version less than 3.0.0
1. Press the alarm control panel synchronization button;
2. LED 3 on the control unit stays on for 3 minutes, indicating that it is waiting for the sensor to re-
gister;
3. Insert the battery (If the sensor already has a battery, press the synchronization key);
4. The status LED will ash green indicating the correct registration. If it ashes red, the registration
was not carried out and the procedure must be repeated.
7. Deleting the sensor record
To remove the device from the control panel, two steps are necessary, one directly on the sensor and
the other on the control panel.
» Sensor: press and hold the sensor timing switch for approximately 10 seconds, watching the sta-
tus LED blink red twice slowly.
» Alarm control panel: enter the programming mode and type the command below:
Enter Enter
01 to 64
zone no.71
+ + +
For other ways to remove the sensor from the control panel, please refer to the complete manual of
the AMT 8000 control panel.

9
8. Identifying the best location for installation
The IVP 8000 Pet sensor has signal level indications for communication with the AMT 8000 control
panel, to help choose the best installation location. Follow the procedure:
1. Take the sensor, duly registered, to the place to be installed;
2. Check the position where the sensor can cover the entire environment, respecting the installation
height, according to the image in the item Detection range;
3. Position the sensor in the exact location where it will be installed and perform a transmission throu-
gh a detection or tamper opening;
4. Observe the color that the LED will light and check in the following table if the sensor can be ins-
talled in that location.
LED status level of communication
Green Excellent signal level (recommended installation location)
Orange Local regular signal level not recommended for installation
(communication failure may occur)
Red No communication (do not install on site)
Blue Intrusion Detection
If the signal level is not excellent, reposition the sensor or use a REP 8000 repeater and perform
the procedure again. For more information about the REP 8000 repeater, consult the manual on the
website: www.intelbras.com.br.
9. Installation
After identifying the best installation location, follow the recommendations:
»It must be installed at a height of 1.8 m to 2.2 m and positioned so that the intruder makes
transverse movements to the sensor’s detection radius.
»It is not recommended to install the sensor tilted up or down as this may impair its PET or detection
function.
»Make sure the sensor is securely xed and not subject to jitter in order to avoid unwanted triggers.
The IVP 8000 Pet sensor does not have an articulator. Therefore, for its installation, follow the
procedure:
1. Remove the lower front cover and remove the rear bracket from the base by sliding it downwards,
as shown in the picture.

10
2. For installation directly on the wall or in a corner of the wall, break the indicated seals for the holes
in the bracket.
Wall mounted Mounted on the corner of the wall
3. After xing the bracket, t the base on the bracket and slide it down and then t the lower front
cover.
10. Trial period
The sensor goes into test mode, for 15 minutes, after registering the sensor in the AMT 8000 control
panel or pressing the synchronism key so that it is possible to carry out positioning adjustments.
During this period, at any motion detection, the blue LED lights up and a trigger is generated, regar-
dless of the settings that are applied.