Intelbras IVP 1000 PET User manual

User manual
IVP 1000 Pet SF
English

IVP 1000 Pet SF
Wireless passive infrared motion sensor
Congratulations, you have just purchased a product with Intelbras quality and safety.
The IVP 1000 Pet SF motion sensor features passive infrared ray detection technology,
with advanced signal analysis technology that prevents accidental triggering.

Care and safety
» Follow all the instructions in the manual for the correct assembly and installation of the product;
» LGPD – Data processing by Intelbras: Intelbras does not access, transfer, capture or process any type of personal data
from this product;
» Fix the sensor on stable surfaces, where there are no vibrations;
» This sensor is intended for indoor environments;
Internal Semi-open External
» Do not use the sensor in areas with sudden temperature changes such as near air conditioners and heaters, fans, refri-
gerators and ovens. Do not expose the sensor directly or to sunlight reections;
» Do not touch the surface of the infrared sensor (PIR), if necessary, use a cleaning cloth;
» Do not place objects in front of the sensor. To ensure the detection area, avoid curtains, screens, screens, or any object
that may interfere with its coverage area;
» Wireless communication technology, when exposed to environments with high power radiation, may suffer interference
and have its performance impaired. Example: locations close to TV towers, AM/FM radio stations, amateur radio stations,
routers, etc;
» The recommended installation height is between 2.0 and 2.40 meters. If the sensor is installed at a different height than
the specied one, its detection and Pet function may be impaired in such a way as to nullify the Pet immunity;
» The sensor must be installed where a possible intruder can be easily detected, that is, where it moves across the detection
beams (see gure below).

» The Pet function is intended for at animals weighing up to 20 kg. If the animal is on top of a bench, for example, the
Pet function can be canceled.
Scan (top view)
0 2 4 6 8
8
6
6
4
4
2
2
0
10 12 (m)
8(m)
90°
Detection range (side view)
2 – 2,40 meters
1,2 4 6 8 10 12 m
zone
zero

Summary
1. Technical specications 6
2. Characteristics 6
3. Product 7
4. Sensor opening 7
5. Sensor stabilization 7
6. IVP 1000 Pet SF sensor registration 7
7. Installation 8
8. Test 9
9. Sensor conguration 9
9.1. IVP 1000 Pet SF sensor sensitivity adjustment......................................................9
9.2. IVP 1000 Pet SF sensor operation mode .........................................................10
10. Low battery sensor 10
11. Battery replacement 10
12. Homologation 10
Warranty term 11

6
1. Technical specications
Operating voltage 3 Vdc
Battery LITHIUM CR123A
Operating current 14 mA
Consumption at rest 4 uA
Detection angle 90°
Detection range 12 meters
Detection method RIP
Immunity to crawling animals Up to 20 kg
Ssensitivity adjustment 3 levels (1P-2P-3P)
Startup time Up to 60 seconds
Operating Temperature -10°C to 50°C
Transmission frequency 433.92 MHz
Transmission distance Up to 100m without barriers
Modulation OK
Installation height range 2.0 to 2.4 meters
Recommended installation height 2.1 meters
Dimensions (W × H × D) 50 × 75 × 42mm
Weight 0,047 Kg
2. Characteristics
» Microcontrolled signal processing;
» Automatic temperature compensation to reduce false alarms;
» Immunity to white light up to 10,000 lux;
» High RFI/EMI immunity;
» Dual-element passive infrared;
» Adjustable infrared (PIR) sensitivity;
» Immunity to crawling animals weighing less than 20 kg;
» Power: LITHIUM battery 3 Vdc – CR123A;
» Battery level sensor.

7
3. Product
3P
1P
LD1
PROG
CH1
IVP 1000 PET SF
2P
3
4
5
6
7
1
2
8
9
10 10
10
10
1. Front Cover
2. Fresnel lens
3. PROG button
4. Sensitivity selector switch
5. LED trigger
6. PIR sensor
7. Battery connector
8. Antenna
9. Basis
10. Screw seal
4. Sensor opening
To access the IVP 1000 Pet SF sensor board for battery change or conguration, squeeze the base latch, located at the
bottom. See image below:
3P
1P
LD1
PROG
CH1
IVP 1000 PET SF
2P
5. Sensor stabilization
After inserting the battery, the sensor goes into stabilization mode and the red LED ashes for a few seconds. When stabi-
lization is complete, the red LED will stop ashing.
6. IVP 1000 Pet SF sensor registration
To register the sensor in the control panel, check the procedure in the manual of the control panel used and trigger a
trigger by moving in front of the sensor or press the PROG button located on the sensor board.
Note: do not register the sensor in the control unit during the stabilization time.

8
7. Installation
After identifying the best installation location, follow the recommendations:
» It must be installed at a height of 2.0 m to 2.4 m and positioned so that the intruder makes transverse movements to
the sensor’s detection radius.
» It is not recommended that the sensor be installed at an angle or using an articulator, as its detection range and Pet
function may be impaired in such a way as to cancel the function.
» Make sure the sensor is securely xed and not subject to jitter in order to avoid unwanted triggers.
1. Remove the front cover by pressing the base latch, as shown in item 4. Sensor opening.
2. For direct-to-wall or corner-wall installation, remove the plate and break the indicated seals for the screw holes in
the base.
Wall mounted Mounted on the corner of the wall
3. Após a xação da base, encaixe a tampa frontal na parte superior da base e aperta a parte inferior da tampa frontal para
que a mesma se encaixe na base.
Encaixe
Aperte
Fitting
Press

9
8. Test
Once installed and running, walk across the area to be protected simulating a possible intrusion into the environment.
Check if the sensor is able to detect your movements during the course, through the Red LED (triggering). Adjust the
sensitivity if necessary or reposition the sensor. Be sure to take all precautions and follow installation recommendations to
get the best operating performance from your product.
Note: if the control panel used is Intelbras, put it in test mode, this way it will not be necessary to observe the LED, as
the control panel will indicate the functioning of the sensor through siren beeps. For more information, consult the central
manual on the website: www.intelbras.com.br.
9. Sensor conguration
After the sensor is properly installed, perform the adjustments according to the information below:
9.1. IVP 1000 Pet SF sensor sensitivity adjustment
The selector switch (CH1) is used to control the detection sensitivity where it is possible to adjust the 3 detection levels.
» 1P: maximum sensitivity for motion detection;
» 2P: medium sensitivity (factory default);
» 3P: minimal sensitivity for greater robustness against accidental triggering.

10
9.2. IVP 1000 Pet SF sensor operation mode
After being energized, the sensor will operate during the test period for 15 minutes so that the installer can make all
adjustments to the sensor’s positioning. During this period, at any movement detection, the LED lights up and a trigger is
generated.Then the sensor will operate in economy mode.
» Economy Mode: when detecting movement, it turns on the LED, triggers and goes into hibernation, remaining for
a period that can last from 30 seconds (environment with little movement) to 2 minutes (environment with a lot of
movement). During this sleep period the LED is not activated and no new triggers are generated, as a notication has
just been sent to the control panel. After the hibernation period, the sensor monitors the environment again until a new
movement is detected.
This ability to learn from the movement of the environment means that in places with a lot of movement, periodic
and non-continuous shots are generated, in turn, saving battery life.
Após inserir a
bateria o LED
azul piscará por
alguns segundos
e não há
detecção.
A qualquer
detecção o
LED
acende e
informa a
central.
Após a detecção do primeiro
movimento o sensor informa
a central e entra no
período de hibernação.
Durante esse período o
sensor entra em
hibernação e não
detecta movimento.
Passado o tempo
de hibernação o
sensor volta a
detectar movimento,
iniciando o ciclo
novamente.
15 min
Período de
estabilização
Período de
teste Modo Econômico
After inserting the battery,
the blue LED will ash for a
few seconds and there will
be no detection.
Stabilization period Trial period Economy mode
At any detection,
the LED comes on
and informs the
control panel.
After detecting the rst movement, the
sensor informs the control panel and enters
the hibernation period.
During this period, the
sensor sleeps and does not detect
movement.
After the rest time, the sensor
detects movement again, restar-
ting the cycle.
10. Low battery sensor
The IVP 1000 Pet SF sensor controls the battery level and if it is critical it sends the information to the control panel during
triggering. In addition, the sensor also signals through the LED, after each activation of the sensor the LED lights up (as
usual) and then ashes indicating low battery.
Use only quality batteries with the correct sizing for the device, and with typical use of the device, the expected battery life
is 1 to 2 years, which may be inuenced by the number of activations, weather conditions and mode of settings.The battery
model must be CR123A 3V, using one (1) battery per sensor.
11. Battery replacement
To replace the product’s battery:
» Remove the dead battery;
» Press the PROG button or wait a few seconds for the circuit to completely discharge;
» Connect new battery.
12. Homologation
18969-21-00160
This equipment is not entitled to protection against harmful interference and may not cause interference in properly
authorized systems. This is a product approved by Anatel, the approval number can be found on the product label, for
queries go to the website: sistemas.anatel.gov.br/sch .