Intelbras iIVA 5040 AT User manual

User manual
IVA 5040 AT
IVA 5080 AT

IVA 5040 AT and IVA 5080 AT
Articulated active sensors
Congratulations, you have just purchased a product with Intelbras quality and safety.
The IVA 5040 AT and IVA 5080 AT sensors were developed with the objective of offering an effective
infrared barrier, combined with a high exibility of installation and alignment through its articulation
system. Both models have more congurations to meet the demands of installation scenarios, always
maintaining the quality of Intelbras products. Read the information carefully for the correct use of both
sensor models.

Care and safety
» Install the sensor in a stable location that is not subject to ickering.
» Install the transmitter and receiver so that they are aligned;
» LGPD - General Law for the Protection of Personal Data: Intelbras does not access, transfer, capture, or perform any other
type of treatment of personal data from this product.
» Do not install the sensor in locations where beam obstruction may occur. Check that there are no plants, branches or
other objects that could obstruct the sensor beam;
» Do not install the receiver and transmitter with the lens facing the sun;
X
X
X
X
» Size the power supply and power cord correctly;
» Do not leave the cable exposed to the sun, rain or moisture;
» Do not install the sensor above the recommended distance;
» Always check that there are no reections on clear and polished surfaces, which can prevent the sensor from triggering.
Do walking tests in different positions along the barrier to make sure there are no reections;
» Use the sealing rubber correctly to prevent insects from entering the sensor;
» To clean the outside of the sensor, use a cloth moistened with water; never use chemicals.
» For installation of stacked sensors, the maximum number of sensors installed is 3 (three), they must be in different and
crossed frequency channels, as shown in the following image.
TX
CANAL 3
RX
CANAL 3
X
TX
CANAL 1
RX
CANAL 1
RX
CANAL 2
TX
CANAL 2
TX
CANAL 3
RX
CANAL 3
TX
CANAL 1
RX
CANAL 1
RX
CANAL 2
TX
CANAL 2
RX
CANAL 1
TX
CANAL 1
TX
CHANNEL 3
RX
CHANNEL 3
RX
CHANNEL 3
TX
CHANNEL 3
TX
CHANNEL 1
RX
CHANNEL 1
RX
CHANNEL 1
TX
CHANNEL 1
RX
CHANNEL 2
TX
CHANNEL 2
TX
CHANNEL 2
RX
CHANNEL 2
TX
CHANNEL 1
RX
CHANNEL 1

» For installing sensors in perimeters, always follow the sensor layout below:
PERÍMETRO
TX
CANAL 2
TX
CANAL 2
RX
CANAL 2
RX
CANAL 2
RX
CANAL 3
RX
CANAL 1
TX
CANAL 1
TX
CANAL 3
TX
CHANNEL 1
TX
CHANNEL 2
TX
CHANNEL 2
Perimeter
RX
CHANNEL 1
RX
CHANNEL 2
TX
CHANNEL 3
RX
CHANNEL 3
RX
CHANNEL 2
» In order to avoid interference between sensors that may be on the same channel, respect the side protection distance
as specied below:
Distância de Proteção Lateral
TX
CANAL 1
RX
CANAL 1
TX
CANAL 1
RX
CANAL 1
TX
CHANNEL 1
Side protection distance
RX
CHANNEL 1
TX
CHANNEL 1
RX
CHANNEL 1

» For the IVA 5040 AT sensor, follow the protection distances below:
Distance between TX and RX
20 m 40 m 60 m1
Side Protection Distance (DPL) >2 m >3 m >4 m
Vertical Protection Distance (DPV) Maximum stacking of 3 sensors
» For the IVA 5080 AT sensor, follow the protection distances below:
Distance between TX and RX
40 m 80 m 120 m1
Side Protection Distance (DPL) >3 m > 5 m >7 m
Vertical Protection Distance (DPV) Maximum stacking of 3 sensors
1
Distance to indoor area only.
That is, for both IVA 5040 AT and IVA 5080 AT, the side protection distance is always the distance between RX and TX
divided by 20 (twenty) plus 1 (one) meter.
Distance between TX and RX
DPL> + 1 [m]
20
!
In outdoor environments with a high rate of fog or rain, install the sensors at a maximum of 50% of
the distance specied for each model, in order to avoid false alarms.

Summary
1. Technical specications 7
2. Product 8
3. Installation 9
4. Troubleshooting 13
Warranty term 14

7
1. Technical specications
Model IVA 5040 AT IVA 5080 AT
Number of beams 1 2
Power supply voltage 10 ~ 24 Vdc / Vac (without polarity)
Consumption current (TX + RX) ≤65 mA
Frequency channels 3 channels, frequencies 1, 2 and 3
Maximum protection distance
External 40 m 80 m
Indoor 60 m 120 m
Alarm output
NA and NF output
2 A @ 24 Vdc
Alarm Time ≥ 2s
Response time 50 ms to 1s, adjustable by trimpot
Detection method Block 1 beam Block 2 simultaneous beams
Alignment indication green LED
Trigger indication red LED
Horizontal Alignment 360°
Vertical Alignment 180°
Solar lter for outdoor environments Yes
Operating temperature -10° to +55°C
IP protection grade IP55
Dimensions (B × W × D) 8 × 24 × 7 cm 8 × 35 × 7 cm
Weight 0.4 KG 0.7 kg

8
2. Product
5
4
3
2
1
TEMPO
RESPOSTA
5
3
1
1
1
1
1
2
2
3
3
3
34
4
5
5
66
1
2
3
4
5
6
IVA 5080 AT
IVA 5040 AT
Alimentação
Saída de Alarme
Canais de Frequência
LED On TX
Ajuste do Tempo de Resposta
LEDS Alinhamento e Disparo RX
TX RX TX RX
-
+
-
+
Su p o r te
Articulável
Gabinete
Principal
Tamp a
Frontal
360°
180°
360°
180°
IVA 5080 AT
IVA 5040 AT
Main Cabinet
Front cover
Articulating
support
360°
TX TXRX RX
360°
180° 180°
5
3
6
2
2
1
1
1
1
3
34
46
3
5
1. Power
2. Alarm output
3. Frequency channels
4. LED On TX
5. Response time adjustment
6. LEDs alignment and trigger RX

9
3. Installation
1. For security reasons, it is necessary to open the sensors to identify which is the transmitter and which is the receiver.
Here’s how to open the sensor cabinet and perform the necessary identication:
5
4
3
2
1
TEMPO
RESPOSTA
-
+
5
3
1
-
+
IVA 5080 AT
IVA 5040 AT
Identificação TX e RX
Remova o parafuso
Remova a tampa frontal
conforme movimento indicado
na figura, utilize abertura localizada
na parte inferior da tampa frontal
para facilitar a remoção
Remove the screw
TX and RX identication
IVA 5040 AT
IVA 5080 AT
Remove the front cover as shown in the
gure, use the opening located at the
bottom of the front cover to facilitate
removal
2. After identication, run the cable as shown in the following image to connect it to the terminal block:
Vista posterior Vista lateral
Cabo
Rear view Side view
Cable

10
3. Secure the sensors in the installation position following the recommendations below:
» Do not install the sensor upside down.
» Orient yourself by the positioning arrows located on the articulated sensor support.
Down Down
Down Down
4. Turn on the power on the receiver and transmitter board (10 ~ 24 Vdc / Vac - no polarity). After that, connect the wires
from the alarm output to the zone input of your alarm panel:
FONTE
+12V
GND
CM
NF
NA
10 ~24
10 ~24
Conectar àCentral
de Alarmes
RECEPTOR
TRANSMISSOR
Transmitter Receiver
Connect the
alarm control panel
5. Congure the frequency channel using the FREQ jumper. For the sensor to function correctly, the transmitter ( TX ) and receiver
( RX ) must be on the same frequency channel:
Frequency channels
3
FREQ
2
1
Freq.
Position 1 - Frequency channel 1 (factory default)
Position 2 - Frequency Channel 2
Position 3 - Frequency Channel 3