Interacoustics AT235 User manual

D-0105059-D - 2016/11
Instructions for Use
AT235
Impedance Audiometer
EN Instructions for Use
ES
Manual de instrucciones
PT
Instruções de Utilização

Instructions for Use - EN
Impedance Audiometer AT235

Table of Contents
1Introduction.............................................................................................................. 1
1.1 About this Manual................................................................................................................1
1.2 Intended Use.......................................................................................................................1
1.3 Contraindications for performing impedance audiometry ...................................................1
1.4 Product description..............................................................................................................2
1.5 About warnings and cautions..............................................................................................3
2Unpacking and Installation....................................................................................... 5
2.1 Unpacking and Inspection...................................................................................................5
2.2 Markings..............................................................................................................................6
2.3 Important safety instructions ...............................................................................................7
2.4 Connections ........................................................................................................................9
2.5 Calibration cavities..............................................................................................................9
2.6 Changing probe system ....................................................................................................10
2.7 Safety Precautions to take when connecting the AT235. .................................................11
2.8 License..............................................................................................................................12
3Operating Instructions............................................................................................ 13
3.1 Handling and selection of ear tips.....................................................................................14
3.2 Switching the AT235 on and off ........................................................................................14
3.3 Probe Status......................................................................................................................15
3.4 Use of standard and clinical probe system .......................................................................16
3.5 AT235 Stand-alone operation...........................................................................................16
3.5.1 AT235 Stand-alone operation panel.......................................................................16
3.5.2 Startup.....................................................................................................................17
3.5.3 Instrument settings – language, printer, date & time, etc. ......................................18
3.5.4 Test and module selection......................................................................................19
3.5.5 Tympanometry test screens....................................................................................19
3.5.6 Audiometry test screen ...........................................................................................24
3.5.7 Start and stop of a tympanometric test...................................................................25
3.5.8 Save........................................................................................................................26
3.5.9 View historical sessions..........................................................................................27
3.6 Operating in Sync Mode (only with Diagnostic Suite).......................................................28
3.6.1 PC Power Configuration .........................................................................................28
3.6.2 Starting from OtoAccess™ .....................................................................................28
3.6.3 Starting from Noah 4...............................................................................................29
3.6.4 Crash Report...........................................................................................................29
3.6.5 Instrument setup .....................................................................................................30
3.7 Using Sync Mode..............................................................................................................31
3.7.1 Using IMP Sync.......................................................................................................31
3.7.2 Using AUD Sync .....................................................................................................33
3.7.3 SYNC Mode ............................................................................................................35
3.7.4 Client Upload...........................................................................................................36
3.7.5 Session download...................................................................................................36
4Maintenance ........................................................................................................... 39
4.1 General Maintenance Procedures ....................................................................................39
4.2 General Maintenance Procedures ....................................................................................40
4.3 Cleaning the Probe Tip......................................................................................................41

4.4 Concerning Repair ............................................................................................................42
4.5 Warranty............................................................................................................................42
4.6 Periodic calibration............................................................................................................43
5Specifications......................................................................................................... 45
5.1 AT235 Technical Specifications........................................................................................45
5.2 Electromagnetic Compatibility (EMC) ...............................................................................54

AT235 Instructions for Use - EN Page 1
1Introduction
1.1 About this Manual
This manual is valid for the AT235 firmware version 1.8. (Model 1077).
The product is manufactured by:
Interacoustics A/S
Autiometer Allé 1
5500 Middelfart
Denmark
Tel.: [phone]
Fax: [phone]
E-mail: [e-mail]
Web: www.interacoustics.com
1.2 Intended Use
The AT235 is an automatic impedance audiometer with built-in screening audiometry suited for screening, as
well as diagnostic work. Neonatal screening programs will particularly appreciate the presence of high probe
tone tympanometry, allowing more reliable tympanometric results in neonates.
The AT235 tympanometer is intended to be used by an audiologist, hearing healthcare professional, or
trained technician in a quiet environment.
1.3 Contraindications for performing impedance audiometry
•Recent stapedectomy or other middle ear surgery
•Discharging ear
•Acute external auditory canal trauma
•Discomfort (eg severe otitis externa)
•Occlusion of the external auditory canal
•Presence of tinnitus, hyperacusis or other sensitivity to loud sounds may contraindicate testing when
high intensity stimuli are used
Testing should not be performed on patients with such symptoms without a medical doctor’s approval.
Visual inspection for obvious structural abnormalities of the external ear structure and positioning as well as
the external ear canal should be performed before testing.

AT235 Instructions for Use - EN Page 2
1.4 Product description
The AT235 consist of the following parts:
Included Parts
AT235 instrument
Clinical Probe System1
Diagnostic Probe System1, 2
Power supply unit UE60
Contralateral headphone1
Daily check cavity
CAT50 (option)
Patient Response (Option)
Printer kit (Option)
Wall mounting kit (Option)
Cleaning cloth
Assortment bag BET55
1Applied part as according to IEC60601-1
2 One can be selected.

AT235 Instructions for Use - EN Page 3
1.5 About warnings and cautions
Throughout this manual the following meaning of warnings, cautions and notices are used:
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION, used with the safety alert symbol, indicates a hazardous situation
which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to personal injury.

AT235 Instructions for Use - EN Page 4

AT235 Instructions for Use - EN Page 5
2Unpacking and Installation
2.1 Unpacking and Inspection
Check box and contents for damage
When the instrument is received please check the shipping box for rough handling and damage. If the box is
damaged it should be kept until the contents of the shipment have been checked mechanically and
electrically. If the instrument is faulty please contact your local distributor. Keep the shipping material for the
carrier’s inspection and insurance claim.
Keep carton for future shipment
AT235 comes in its own shipping carton, which is specially designed for the AT235. Please keep this carton.
It will be needed if the instrument has to be returned for service.
If service is required please contact your local distributor.
Reporting Imperfections
Inspect before connection
Prior to connecting the product it should once more be inspected for damage. All of the cabinet and the
accessories should be checked visually for scratches and missing parts.
Report immediately any faults
Any missing part or malfunction should be reported immediately to the supplier of the instrument together
with the invoice, serial number, and a detailed report of the problem. In the back of this manual you will find a
"Return Report" where you can describe the problem.
Please use the "Return Report"
Use of the return report provides the service engineer with the relevant information to investigate the
reported issue. Without this information, there may be difficulty in determining the fault and repairing the
device. Please always return the device with a completed Return Report in order to guarantee that correction
of the problem will be to your satisfaction.
Use only specified power supply unit UE60 type

AT235 Instructions for Use - EN Page 6
2.2 Markings
The following markings can be found on the instrument:
Symbol
Explanation
Type B applied parts.
Patient applied parts that are not conductive and can be immediately
released from the patient.
Refer to instruction manual
WEEE (EU-directive)
This symbol indicates that when the end-user wishes to discard this product,
it must be sent to separate collection facilities for recovery and recycling.
0123
The CE-mark indicates that Interacoustics A/S meets the requirements of
Annex II of the Medical Device Directive 93/42/EEC. TÜV Product Service,
Identification No. 0123, has approved the quality system.
Year of manufacture
Do not re-use Parts like ear-tips and similar are for single use only
Display Port Connection – HDMI type
“ON” / “OFF” (push-push)

AT235 Instructions for Use - EN Page 7
2.3 Important safety instructions
Read this instruction manual carefully and completely before using the product
1. External equipment intended for connection to signal input, signal output or other connectors shall
comply with relevant IEC standard (e.g. IEC 60950 for IT equipment). In these situations an optical
isolator is recommended to fulfill the requirements. Equipment not complying with IEC 60601-1 shall be
kept outside the patient environment, as defined in the standard (usually 1.5 meter). If in doubt, contact
qualified medical technician or your local representative.
2. This instrument does not incorporate any separation devices at connections for PC’s, printers, active
speakers etc. (Medical Electrical System). A galvanic l isolator is recommended to fulfill the
requirements. For safe setup please refer to section 2.3.
3. When the instrument is connected to a PC and other items of equipment of a medical electrical system
assure that the total leakage current cannot exceed the safety limits and that separations have the
dielectric strength, creepage clearances and air clearances required fulfilling the requirements of IEC/ES
60601-1. When the instrument is connected to a PC and other similar items be aware of not touching the
PC and patient simultaneously.
4. To avoid the risk of electric shock, this equipment must only be connected to supply mains with
protective earth.
5. Do not use any additional multiple socket-outlet or extension cord. For safe setup please refer to section
2.3
6. This instrument contains a coin-type lithium battery. The cell can only be changed by service personnel.
Batteries may explode or cause burns, if disassembled, crushed or exposed to fire or high temperatures.
Do not short-circuit.
7. No modification of this equipment is allowed without Interacoustics authorization.
8. Interacoustics will make available on request circuit diagrams, component part lists, descriptions,
calibration instructions, or other information that will assist service personnel to repair those parts of this
audiometer that are designated by the Interacoustics as repairable by service personnel.
9. For maximum electrical safety, turn off the power from a mains powered instrument when it is left
unused.
10. The instrument is not protected against harmful ingress of water or other liquids. If any spillage occurs
check the instrument carefully before use or return for service.
11. No part of the equipment can be services or maintained while in use with the patient.

AT235 Instructions for Use - EN Page 8
1. Never insert or in any way use the insert headset without a new clean non defect test tip. Always make
sure that foam or ear-tip is mounted correctly. Ear tips and foam are single use.
2. The instrument is not intended to be used in environments exposed to fluid spills.
3. The instrument is not intended to be used in oxygen rich environments or use in conjunction with
flammable agents.
4. Check calibration if any parts of the equipment is exposed to shock or rough handling.
NOTICE
1. To prevent system faults take appropriate precautions to avoid PC viruses and similar.
2. Use only transducers calibrated with actual instrument. To identify a valid calibration, the serial number
for the instrument will be marked on the transducer.
3. Although the instrument fulfils the relevant EMC requirements precautions should be taken to avoid
unnecessary exposure to electromagnetic fields, e.g. from mobile phones etc. If the device is used
adjacent to other equipment it must be observed that no mutual disturbance appears. Please also refer
to EMC considerations in section 5.2
4. Use of accessories, transducers and cables other than specified, with the exception of transducers and
cables sold by Interacoustics or representatives may result in increased emission or decreased immunity
of the equipment. For list of accessories, transducers and cables that fulfils the requirements please
refer to section 5.2
5. Within the European Union it is illegal to dispose electric and electronic waste as unsorted municipal
waste. Electric and electronic waste may contain hazardous substances and therefore has to
be collected separately. Such products will be marked with the crossed-out wheeled bin shown
below. The cooperation of the user is important in order to ensure a high level of reuse and
recycling of electric and electronic waste. Failing to recycle such waste products in an
appropriate way may endanger the environment and consequently the health of human
beings.
6. Outside the European Union, local regulations should be followed when disposing of the product after its
useful life.

AT235 Instructions for Use - EN Page 9
2.4 Connections
1
Probe
Dedicated probe connection
2
LAN
LAN (Not used)
3
USB B
For PC connection
4
USB A
For printer, mouse, keyboard, Memory stick
5
HDMI
For external monitor or projector
6
In 24 V
Use only specified power supply unit UE60 type
7
Trigger in / out
Cochlear implant trigger option
8
Pat. Resp.
Patient response button
9
Right
Audiometry Right output
10
Left
Audiometry Left output
11
Contra
Contra transducer output
2.5 Calibration cavities
You can use the 0.2 ml, 0.5 ml, 2.0ml and 5 ml for validity check of the probe calibration.
To perform a calibration check, select a protocol the measures a tympanogram.
Do not use an ear tip! Place the probe tip completely into the cavity. Perform the measurement. Check the
volume that was measured.
The allowed tolerance in the volume measurement is ±0.1 ml for cavities up to 2 ml and ±5% for larger
cavities. These tolerances are applicable for all probe tone frequencies.
We strongly recommend calibrating probe and contra phone at least once a year.

AT235 Instructions for Use - EN Page 10
2.6 Changing probe system
Change between the standard and clinical probe as follows:
1. Locate the probe connection on the back of the unit.
2. Open the 2 locks by pushing them to the sides.
3. Swap to the other probe system.
4. Close the 2 locks by pushing them to the centre.

AT235 Instructions for Use - EN Page 11
2.7 Safety Precautions to take when connecting the AT235.
NOTICE
Please note that if connections are made to standard equipment like printers and networks, special
precautions must be taken in order to maintain medical safety.
Please follow instructions below.
Fig 1. AT235 used with the medically approved power supply UE60.
Fig. 2. AT235 used with, a medically approved safety transformer and a wired connection to a PC.
Mains outlet Medical power supply AT235 alone
AT235
Medical power supply
Mains outlet Medically approved
safety transformer
PC power supply PC
Printer

AT235 Instructions for Use - EN Page 12
Fig. 3. AT235 used with the medically approved power supply UE60 and printout with MPT-III printer.
The separable mains plug is used to safely disconnect mains from the device. Do
not position the power supply in a position so that it is difficult to disconnect the
device.
2.8 License
When you receive the AT 235 it already contains the license you have ordered. If you would like to add
licenses that are available in AT235, please contact your dealer for a license.
Mains outlet Medical power supply AT235 alone
MPT-III printer
Fully charged,
WITHOUT POWER SUPPLY
CONNECTED

AT235 Instructions for Use - EN Page 13
3Operating Instructions
The instrument is switched on by pressing the ON button on the unit. When operating the instrument, please
observe the following general precautions:
1. Use this device only as described in this manual.
2. Use only the disposable Sanibel ear tips designed for use with this instrument.
3. Always use a new ear tip for each patient to avoid cross-contamination. The ear tip is not designed
for reuse.
4. Never insert the probe tip into the ear canal without affixing an ear tip as omission may damage the
patient’s ear canal.
5. Keep the box of ear tips outside the reach of the patient.
6. Be sure to insert the probe tip in a way which will assure an airtight fit without causing any harm to
the patient. Use of a correct and clean ear tip is mandatory.
7. Be sure to use only stimulation intensities acceptable to the patient.
8. When presenting contralateral stimuli using the insert phones – do not insert the phones or in any
way try to conduct measurements, without a correct insert ear tip in place.
9. Clean the headphone cushion regularly using a recognized disinfectant.
10. Contraindications to testing include recent stapedectomy or middle ear surgery, a discharging ear,
acute external auditory canal trauma, discomfort (e.g, severe otitis externa) or occlusion of the
external auditory canal. Testing should not be performed on patients with such symptoms without a
medical doctor’s approval.
11. The presence of tinnitus, hyperacusis or other sensitivity to loud sounds may contraindicate testing
when high intensity stimuli are used.
NOTICE
1. Careful handling of the instrument whenever in contact with a patient should be given high priority.
Calm and stable positioning while testing is preferred for optimal accuracy.
2. The AT235 should be operated in a quiet environment, so that measurements are not influenced by
outside acoustic noises. This may be determined by an appropriately skilled person trained in
acoustics. ISO 8253 Section 11, defines a quiet room for audiometric hearing testing in its
guideline.
3. It is recommended that the instrument be operated within an ambient temperature range of 15°C /
59°F – 35°C / 95°F.
4. The headphone and insert phone are calibrated to the AT235 – introducing transducers from other
equipment requires a re-calibration.
5. Never clean the transducer housing with water or insert non-specified instruments into the
transducer.
6. Do not drop and avoid other undue impact to this device. If the instrument is dropped or otherwise
damaged, return it to the manufacturer for repair and/or calibration. Do not use the instrument if any
damage is suspected.
7. Although the instrument fulfils the relevant EMC requirements, precautions should be taken to avoid
unnecessary exposure to electromagnetic fields, e.g. from mobile phones etc. If the device is used
adjacent to other equipment, caution must be taken to observe that no mutual disturbance appears.

AT235 Instructions for Use - EN Page 14
3.1 Handling and selection of ear tips
When using the AT235 probe and CIR55 contra phone, Sanibel ear tips must be used.
The Sanibel ear tips are single use only and should not be reused. Reuse of ear tips can lead to the spread
of infection from patient to patient.
The probe and CIR55 contra phone must be fitted with an ear tip of a suitable type and size before testing.
Your choice will depend on the size and shape of the ear canal and ear. Your choice may also depend on
personal preference and the way you perform your test.
When performing a quick impedance screening test you may choose an umbrella shaped ear
tip. Umbrella ear tips seal the ear canal without the probe tip going into the ear canal. Press
the ear tip firmly into the ear canal in such a way that a seal remains during the complete test.
For more stable testing, we recommend using an extension cord with a mushroom shaped
ear tip. Make sure that this ear tip inserts completely into the ear canal. Mushroom shaped
ear tips allow you to test ‘hands free’ from the AT235. This reduces the chance of contact
noise disturbing the measurement.
Refer to the “Selecting the Correct Ear Tip” Quick Guide included in the AT235 Additional Information
document for an overview of ear tip sizes and selection.
3.2 Switching the AT235 on and off
Switch the AT235 on or off by pressing the ON (1).
NOTICE
The AT235 takes approximately 45 seconds to boot up. Allow the unit to warm up for 1 minute before use.