Interlogix UVP-N120P-36X(-P) User manual

UltraView IP PTZ 36X
Camera User Manual
P/N 1071693D-EN • ISS 05DEC12

Copyright
©
2012 UTC Fire & Security Americas Corporation, Inc.
Interlogix is part of UTC Climate Controls & Security, a unit of United
Technologies Corporation. All
rights reserved.
Trademarks and patents
UltraView name and logo are trademarks of United Technologies.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626
-5923, USA.
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert,
The Netherlands
Certification
N4131
FCC compliance
Class A
: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
ACMA compliance
Notice!
This is a Class A product. In a domestic environment this
product may cause radi
o interference in which case the user may be
required to take adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES
-003.
Cet appareil numérique de la class A conforme à la norme NMB
-
003
du Canada.
European Union
directives
2004/108/EC (EMC directive)
: Hereby, UTC Fire & Security
declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2004/108/EC
2002/96/EC (WEEE directive)
: Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more
information see:
www.recyclethis.info.
Contact information
www.interlogix.com or
www.utcfssecurityproducts.eu
Customer support
ww
w.interlogix.com/customer-support

UltraView IP PTZ 36X Camera User Manual i
Content
Chapter 1 Introduction 1
Product description 1
Features 1
Chapter 2 Installation 3
Installation environment 3
Before you begin 4
Camera description 4
Specifications 5
System requirements 5
Installing the camera 6
Accessing the SDHC card 10
Connections 11
Chapter 3 Using the Web browser 13
Checking your Web browser security level 13
Accessing the camera over the internet 14
Overview of the camera Web browser 15
Configuring the camera 17
Chapter 4 Camera setup 23
Camera information 23
DST time 23
Camera configuration 24
Display information 25
Video recording parameters 26
Camera tamper alarm 30
Adding extra text on-screen 32
Camera image settings 33
Reset camera settings 36
Restore camera settings to default 36
Chapter 5 Motion setup 37
PTZ channel 38
Park action 39
Home preset position 39
Preset position 40
Limit PTZ movement 41
Preset tour settings 43
Shadow Tour settings 46
Privacy masking 48
Time task 49
Clearing customized settings 51

ii UltraView IP PTZ 36X Camera User Manual
Chapter 6 Network setup 53
Chapter 7 Alarm setup 57
Motion detection 57
Event schedule for alarms 59
Alarm set up 60
Chapter 8 Camera management 63
User management 63
Format the SDHC card 66
Firmware upgrade 66
Restore default settings 66
Reboot the camera 67
Chapter 9 Camera operation 69
On-screen display 69
Live mode 69
Searching recorded video for playback 70
Playing back recorded files 72
Viewing logs 72
Searching for logs 73
Archiving recorded files 74
Using predefined presets 75
Appendix A Pin definitions 77
Index 79

UltraView IP PTZ 36X Camera User Manual 1
Chapter 1
Introduction
Product description
The UltraView IP PTZ 36X camera features integrated network remote
monitoring capability with the functions of a high speed dome. It is easy to install
and operate.
The dome camera is ideal for all surveillance requirements in a wide variety of
locations such as roads, airports, railway stations, harbors, stadiums, scenic
areas and parking lots.
This is the user manual for UltraView IP PTZ 36X camera models:
UVP-N120P-36X(-P)
UVP-N120S-36X(-P) (North America only)
UVP-N120F-36X(-P)
Features
This section describes the UltraView IP PTZ 36X camera features.
Built-in Web server
One channel of compressed video stream transmitted via network and
decoded for local display
Supports up to six connections via the network
Supports multiple network transmission protocols
Web access for WAN applications
Management of dome configuration and user permission administration via
Ethernet
IP address dynamic allocation
Built-in driver/receiver
Integrated design ensures high reliability

Chapter 1: Introduction
2 UltraView IP PTZ 36X Camera User Manual
256 presets and 8 tours programmable, each tour with a maximum of 32
configurable presets
Supports up to four shadow tours with a recording time of up to 10 minutes
Up to 24 programmable privacy mask areas (depending on camera models)
Built-in pan/tilt
High-precision motor drive, stable operation, sensitive reaction and precise
positioning
Integrated design with compact construction
360° continuous rotation
Low-speed movement ensures high image stability
Preset positioning tolerance less than 0.1°
Built-in zoom lens
High sensibility and high resolution
Auto focus
Automatic gain control
Auto white balance
Auto IR cut filter

UltraView IP PTZ 36X Camera User Manual 3
Chapter 2
Installation
This chapter provides information on how to install the dome camera.
Installation environment
When installing your product, consider these factors:
• Handling: Handle the camera carefully. Avoid striking, shaking, etc. Improper
handing or storage could damage the camera.
• Electrical: Install electrical wiring carefully. It should be done by qualified
service personnel. The input electricity to the unit has a tolerance of 24 VAC ±
10%. Do not overload the power cord or adapter.
• Ventilation: Ensure that the location planned for the installation of the
camera is well ventilated.
• Temperature: Do not operate the camera beyond the specified temperature,
humidity or power source ratings. The operating temperature of the indoor
camera is between -10°C to 50°C (14°F to 122°F) and that of the outdoor
camera is between -30°C to 60°C (-22°F to 140°F). Humidity is below 90%.
• Moisture: Do not expose the indoor camera to rain or moisture, or try to
operate it in wet areas. The indoor camera is designed for indoor use or
locations only where it is protected from rain and moisture. Turn the power off
immediately if the camera is wet and ask a qualified service person for
servicing. Moisture can damage the camera and also create the danger of
electric shock.
• Cleaning: Clean only with a dry cloth. If the dirt is difficult to remove, use a
mild liquid non-abrasive detergent and wipe gently.
• Protect from strong light: Never face the camera towards the sun. Do not
aim the camera at bright objects. Whether the camera is in use or not, never
aim it at the sun or other extremely bright objects. Otherwise, the camera may
be smeared or damaged.
• Servicing: Do not attempt to service this camera yourself. Any attempt to
dismantle or remove the covers from this product will invalidate the warranty

Chapter 2: Installation
4 UltraView IP PTZ 36X Camera User Manual
and may also result in serious injury. Refer all servicing to qualified service
personnel.
Before you begin
When you receive the product, check the package and contents for damage, and
verify that all items are included. If any of the items are damaged or missing,
please contact your local supplier. If you need to return the unit, you must ship it
in the original box.
The camera is shipped with the following items:
Dome camera
User manual
Quick Start Guide
Camera description
Figure 1: Camera dimensions
Pendant-mount camera
Flush-mount camera

Chapter 2: Installation
UltraView IP PTZ 36X Camera User Manual 5
Figure 2: Overview of the dome camera
1. Ethernet RJ-45 connector.
Connect to the network devices.
2. Video output.
Connect the BNC connector to a CCTV
monitor. Optional.
3. Power supply cord.
Connect +24 VAC power supply.
4. Housing.
5. PTZ module.
6. Bubble.
Specifications
Operating temperature
Pendant housing: -10 to +50 °C (-14 to +122 °F)
Flush housing: -30 to +65 °C (-22 to +149 °F)
Power supply
24 VAC +/- 4 VAC
Power
consumption 30 W (heater on), 15 W (heater off)
Dimensions (mm)
Pendant housing: Ø 220 × 261 mm (Ø 8.66 ×10.27 in.)
Flush housing: Ø 206 × 241 mm (Ø 8.11 × 9.49 in.)
Environmental
Pendant housing: IP66
Flush housing: IP54
Weight
5 kg (11 lb.)
System requirements
For proper operation, adhere to the following operational, cable, and power
requirements for the dome camera.
Cable requirements
Table 1 on page 6 lists the requirements for the cables that connect to the dome
camera.

Chapter 2: Installation
6 UltraView IP PTZ 36X Camera User Manual
Table 1: Recommended cable requirements
Operation
Cable requirement Max. length
feet meters
Data (RS
-485) Not used
Video
75 ohm RG-59 coaxial cable with BNC ends. 750 228
Alarm
Cat 5 cable (recommended) 1250 381
Network
Cat 5 cable (recommended) 492 150
Power
24 VAC cable. To determine the size of cable needed for individual
applications, see “Power cable size and length requirements” below.
Power cable size and length requirements
Use the proper gauge of power cable to ensure proper operation and to avoid
voltage drops. See Table 2 below for the recommended cable gauge for varying
maximum cable lengths and power draws.
Table 2: Recommended power cable gauges based on maximum lengths for an operating
voltage of 24 VAC (±10%)
Wire gauge
mm (diameter) Power
30 W 40 W
Distance
(feet) Distance (m) Distance (feet) Distance (m)
0.80 94 28 70 21
1.00 150 45 112 34
1.25 238 72 179 54
2.00 603 183 452 137
Installing the camera
For basic operation, you need to connect Ethernet, power and video output
cables to the components in the dome shown in Figure 2 on page 5. For
advanced operation, you can also connect any combination of alarm, relay, or
audio cables to the dome.
A qualified service person, complying with all applicable codes, should perform
all required hardware installation.
Note: After removing the protective foil, it is recommended to clean the bubble in
order to ensure a clear view at all times.