Interlogix TruVision TVD-2401 User manual

© 2015 United Technologies Corporation. All rights reserved. P/N 1072939-EN • REV A • ISS 26MAR15
Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved.
TruVision High Definition TVI Dome Installation
Guide
Product overview
This is the Installation Guide for TruVision High Definition TVI
dome TVD-2401/TVD-4401 and TVD-2403/TVD-4403. This
guide describes a standard installation.
Package contents:

Camera with power and
video output cables

3 screws and 3 anchors
for wall or ceiling
installation

Template

Installation Guide
•WEEE and Battery
Disposal

CD
Camera description
TVD-2401/TVD-4401
1. Base
2. IR LED
3. Lens
4. Dome liner
5. Housing
6. Power supply
7. TVI Video output cable (grey)
TVD-2403/TVD-4403
1. Base
2. IR LED
3. Lens
4. Dome liner
5. Housing
6. Power supply
7. TVI video output cable
(grey)
8. CVBS video output cable
(black)
Note:
Please check the camera output settings before setting up a
system. The TVI video output can be only connected to DVR
with TVI signal input. The CVBS output supports the standard
monitor, test monitor, encoder and DVR.
For TVD-2403/TVD-4403, you can connect the white and black
line ends of the WDR switch cable to enable the Wide Dynamic
Range function. The WDR function is disabled by default. If
WDR is enabled, the CVBS output will be blocked out, and
only TVI output is available.
Installation
To install the camera on a ceiling:
1. Using the template, place it level against the mounting
surface and mark the position of the mounting holes.
2. Following all local codes, drill and prepare the mounting
holes.
Drill Template
Hole A: for cables routed through the ceiling
screw hole 1: for Mounting Base
1
1
1
A

2 / 3 P/N 1072939-EN • REV A • ISS 26MAR15
3. Loosen the screws with wrech to remove the housing.
4. Securely fasten the mounting base to the mounting
surface with the screws.
5. Using a 75 ohm coaxial video cable, connect the camera
TVI video output and a TVI DVR, and connect a 12 VDC
power supply to the camera power cable.
6. Adjust the surveillance angle according to the figure
below.
7. Re-attach the housing to the base.
Programming
Programming on TVI output:
Programming on TVI output is available for TVD-2403/TVD-
4403 only.
Once the camera hardware has been installed, you can
configure the camera settings on the TVI DVR.
Please select PTZ protocol as TruVision Coax and click menu
button to call up the camera menu.
For more details, please see the TVI DVR user manual.
Programming on CVBS output:
Programming on CVBS output is available for TVD-2403/TVD-
4403 only.
Programming on CVBS output, you need to connect a monitor
and a TVS-C200 controller (purchase separately) as following
system figure.
The TVS-C200 has one male BNC output and a female output.
Please connect the male output to camera’s CVBS output and
female output to a monitor.
Menu
Specifications
Power supply
12 VDC
Current
TVD-2401/TVD-4401:
Max. 300 mA
TVD-2403/TVD-4403:
Max.333 mA
Power consumption
TVD-2401/TVD-4401:
Max. 3.5W
TVD-2403/TVD-4403:
Max. 4W
Weight
345 g (0.76 lb.)
Dimensions
(Ø × L)
111 x 82 mm (4.4 x 3.2 in. )
Regulatory information
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa Mesa, CA 92626
5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The
Netherlands
FCC compliance
Class A: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and

P/N 1072939-EN • REV A • ISS 26MAR15 3 / 3
used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
ACMA compliance
Notice! This is a Class A product. In a
domestic environment this product may cause
radio interference in which case the user may
be required to take adequate measures.
Canada
This Class A digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe A est
conforme à la norme NMB-0330 du Canada.
Certification
N4131
European Union
directives
12004/108/EC (EMC directive): Hereby, UTC
Fire & Security declares that this device is in
compliance with the essential requirements
and other relevant provisions of Directive
2004/108/EC.
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be disposed
of as unsorted municipal waste in the
European Union. For proper recycling, return
this product to your local supplier upon the
purchase of equivalent new equipment, or
dispose of it at designated collection points.
For more information see:
www.recyclethis.info.
Copyright
© 2015 United Technologies Corporation.
Interlogix is part of UTC Building & Industrial
Systems, a unit of United Technologies
Corporation. All rights reserved.
Trademarks and
patents
The trade names used in this document may
be trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Contact information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.