Intermec TZ2400 User manual

Specifications
Electrical requirements Input voltage: 85 to 264 VAC
Frequency: 47 to 63 Hz
Application Intermec lithium-ion battery pack
(Part No. 063278 or Part No. 068537)
Charge cycle Current limit: 2.0 Amps maximum
Float voltage: 8.2V ± 100 mV
Operating environment Temperature: 0ºC to 40ºC (32ºF to 104ºF)
Humidity: 0 to 95%, non-condensing
Storage environment Temperature: -20ºC to 60ºC (-4ºF to 140ºF)
Humidity: 0 to 95%, non-condensing
Dimensions Approximately 51 x 114 x 165 mm (2 x 4.5 x 6.5 in)
Design and specifications are subject to change without notice.
Warning
To prevent fire or electric shock, do not expose the battery
charger to rain or moisture.
Avertissement
Pour éviter des risques d’incendie ou de choc électrique, ne
pas exposer le chargeur de la batterie à la pluie ou à
l’humidité.
Ordering Power Cords for the Battery Charger
The AC power cord is ordered separately. If you have not already done so,
contact your Intermec sales representative and order one of these Intermec power
cords:
Australia, New Zealand, and China Part No. 586281
Denmark Part No. 586283
Europe Part No. 586267
Italy and Chile Part No. 586282
North America and Central America Part No. 586105
Switzerland Part No. 586276
United Kingdom Part No. 586266
TZ2400 Battery Charger Quick Reference
Guide
The TZ2400 battery charger lets you simultaneously charge up to four battery
packs for the TRAKKERAntares2420 and 2425 terminals and Intermec
5020 Data Collection PC.
This guide describes how to install and use the battery charger. Before using the
charger, please read this guide thoroughly and retain it for future reference. For
help managing battery power, see your TRAKKER Antares 2420 and 2425
Terminal User’s Manual (Part No. 064024) or 5020 Data Collection PC User's
Manual (Part No. 068975).
Choosing a Location for the Battery Charger
Choose an appropriate location for the charger using these guidelines:
•Locate a flat, stable, and clean surface that is within 1.5 m (5 feet) of an
electrical source.
•Make sure there is easy access to the external power supply jack on the
battery charger and to load and unload batteries.
Connecting the Power Supply
The battery charger uses an autoranging external power supply. Plug the external
power supply connector into the jack on the back of the battery charger and then
connect the AC power cord (ordered separately) to the power supply and to an
AC outlet.
Charging a Battery Pack
You can charge up to four Intermec-labeled battery packs (Part No. 063278 or
Part No. 068537) simultaneously, using any slot. The charging time depends on
the condition of the battery. Usually a battery is fully charged in less than 3
hours.
Loading and Unloading a Battery Pack Into the Charger
Align the battery pack with a battery slot on the charger (as shown in the
illustration) and slide the battery pack down until it fits firmly in the charger.
To unload a battery pack from the charger, simply pull it out of the battery slot.
You can unload and use a battery pack before it has been fully charged.
6001 36th Avenue West
P.O. Box 4280
Everett, WA 98203-9280
© 1999 Intermec
All Rights Reserved
P/N 064213-004

Using the Battery Charger
Lithium-ion
battery
pack
TZ2400
battery
charger
External
power
supply
242XIS.001
Status
light
AC power
cord connector
Note: AC power cord
is ordered
separately.
External power
supply connector
External power
supply jack
Interpreting the Status Light
Each charger slot has a status light that indicates the status of the battery pack.
Red The battery pack is charging.
Green The battery pack is fully charged.
Red flashing There is a problem with the battery pack.
Off The battery slot is empty.
Important Recommendations
•Use only Intermec-labeled lithium-ion battery packs (Part No. 063278 or Part
No. 068537) in the battery charger.
•Charge the battery pack immediately before use, or at least within a couple of
days before use.
•Remove the battery pack from the charger within 24 hours after charging is
completed.
•For maximum battery efficiency, the recommended temperature range when
charging is 10ºC to 30ºC (50ºF to 86ºF).
•Be sure nothing metallic comes into contact with the battery charger contacts.
•Do not disassemble the charger. There are no user-serviceable parts in the
charger.
•While the charger is in use, it becomes warm. This is normal.
•Do not place the charger in locations that are extremely hot or cold, dusty or
dirty, very humid, or subject to vibration.
•If the status light continuously flashes or fails to light when a battery pack is
in the slot, if any part of the charger appears worn or damaged, or if any
difficulty arises while using the battery charger, unplug the battery charger
immediately and contact your Intermec service representative.