Interphone F3S User manual

INTERPHONE F3S
Bluetooth Headset for Motorcycle
Features
Auto-Volume Level Adjusting
________________________________________________________________
1

A. PRODUCT DESCRIPTION:
INTERPHONE F3S is a Bluetooth Headset designed for motorcycle rider or
passenger who wishes to have reliable hands-free, wireless and clear
communications while driving. This headset is equipped with hi-tech features
such as: Auto- olume Level Adjusting.
1. MFB or Multi-Function Button
(power on & off / pairing / answer
/ hang-up / reject /
voice dial / intercom connect /
etc.)
2. He dset Plug
3. Volume Up
4. Volume Down
5. St tus Indic tor
6. Left/Right (L/R) E r Spe ker
7. Microphone (On the flexible boom)
8. Ch rger nd He dset Socket
9. Hook
B. CHARGING:
1When the St tus Indic tor (5) turns Red, the battery is low. Charge the unit
using the provided charger.
2Connect the charger’s plug to the Ch rger Socket (8) of the INTERPHONE
F3S. Then, plug the charger to an external power source. (Note: Status
Indicator (5) turns Red when charging).
3When the St tus Indic tor (5) turns Green,
charging is complete.
4Disconnect the charger.
C. POWER ON OR OFF:
Power On: Press the MFB (1) until St tus Indic tor (5) turns blue. Or press for
approximately 3 seconds, a beep will be heard.
Power Off: Press the MFB (1) until St tus Indic tor (5) turns red. Or press for
approximately 5 seconds, until 3rd tone will be heard.
2

D. PAIRING TO YOUR BLUETOOTH MOBILE PHONE:
1.From OFF, press and hold the MFB (1) of the INTERPHONE F3S until the
St tus Indic tor (5) turns blinking red/blue.
2.While the headset is in pairing mode, access the Bluetooth menu of your
phone. Turn on the Bluetooth function then execute a Bluetooth search.
(See your phone’s manual).
3.When the phone displays the list of Bluetooth devices, select BTMOTOF3S
then enter 0000 and press ok. Pairing is successful if the alternating red/blue
lights of the St tus Indic tor (5) changes to blinking blue.
Note: Some phones do not connect automatically to the kit after pairing You
need to press the MFB (1) (1st beep) to connect
Or use the menu of your phone:
Go back to Bluetooth > Paired devices > highlight the name of this
headset (BTMOTOF3S) > press Options > then press Connect
The INTERPHONE F3Sis now ready to use.
E. BASIC OPERATION:
IMPORTANT:
The INTERPHONE F3S needs to be ‘paired’ with your Bluetooth mobile phone
before you can use the following functions. (See Pairing to your Bluetooth
Mobile Phone on section D )
M ke C ll:
-Dial the number using your phone. Audio will automatically be on the headset.
Note: With some phones, audio is always on the phone during an outgoing call
You will need to press the MFB (1) to transfer the audio to your headset
Answer C ll:
- Press the MFB (1) for 1 second to accept a call (1st beep).
End C ll:
-Press the MFB (1) for 1 second to end the call (1st beep).
Reject C ll (For andsfree Profile Phones only):
-Press and hold MFB (1) for 3 seconds (2nd beep). Phone call rejected.
Voice Di l:
3

IMPORTANT: First, make sure to activate the voice dial function of your phone.
Record at least one voice tag. (Kindly refer to the procedure in your phone’s
manual.)
Note: Voice dialing entries must be stored in the phone’s memory, not on the
SIM card!
1.Press the MFB (1) for 1 second (1st beep) to make a voice dial. A voice dial
tone/ beep will be heard on the headset prompting the user to say the voice
tag of the contact to call.
2.Say the voice tag. The voice will be played back to you, and then the phone
will dial the number automatically.
Redi l:
-Press the MFB (1) for 3 seconds (2nd beep). The last dialed number will be
redialed.
Audio Tr nsfer (For Handsfree Profile Phones only):
-During an ongoing call, you can transfer the audio.
He dset to Phone: Press and hold the MFB (1) for 3 seconds (2nd
beep) and the audio will be transferred to the phone.
Phone to He dset: Press the MFB (1) for 1 second (1st beep) and the
audio will be transferred to the headset
Note: For some phones, you may need to accept a connection prompt on the
phone before automatic transfer takes place
Set the Volume:
-Press the Volume Up (3) or Down (4) button repeatedly until the desired level
is reached.
4

Industry Canada (IC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the IC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
* Consult the dealer or an experienced radio/T technician for help.
Oper tion is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may
cause undesired operation of the device.
IC RF R di tion Exposure St tement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
Feder l Communic tions Commission (FCC) St tement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could
void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/T technician for help.
Oper tion is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation of the device.
FCC RF R di tion Exposure St tement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must
follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located
or operating in conjunction with any other antenna or transmitter.
5