Inventus Power PROTRXion M-24V60-TRX User manual

inventuspower.com
[email protected]
+1 877.423.4242
Inventus Power, Inc.
1200 Internationale Parkway
Woodridge, IL 60517
Designed & Manufactured by
PROTRXion™
Quick Start Guide
M-24V60-TRX

2
PROTRXion™ Quick Start Guide
Applicable Models
Document Information
Inventus Power® and PROTRXion™ are trademarks of Inventus Power.
Copyright© 2021 Inventus Power All rights reserved.
Technical Support
If you have any technical questions regarding the PROTRXion™ battery, please contact our
technical support team at:
Phone: [phone]
E-mail: [e-mail]
Model Part No. (CANopen)
M-24V60-TRX (with heater) 58692-302
M-24V60-TRX (without heater) 58692-103
Release Date Revision Scope of Change
2022-06-15 V1.5 Minor edit mode name

3
Contents
Mechanical Features .................................................................................................................... 4
Torque Rating ................................................................................................................................ 5
Power Cables ................................................................................................................................. 5
Communication Cables ............................................................................................................... 5
Pin Definition ................................................................................................................................. 6
Charging ......................................................................................................................................... 6
Module Configuration ................................................................................................................. 7
Wake-Up & Ship Mode ................................................................................................................ 8
Installation ..................................................................................................................................... 8
LED Status/Operation Mode ..................................................................................................... 9
Heater Operation .......................................................................................................................... 9

4
Quick Start Guide
This Quick Installation Guide contains important information regarding the proper installation
of your Proformance Series lithium battery.
Please read the detailed User Manual first and refer to the Software User Guide for further
information.
This guide is valid only for specific Inventus Power products and only for professional users.
If the product is being damaged during the installation process, the standard warranty may
be aected.
Mechanical Features
If you have any questions, please email [e-mail]
Before installation or maintenance of your batteries, the following equipment
is required:
• Rubber gloves
• Safety goggles or other eye protection
• Insulated Torque Wrench / Philips Screwdriver
• Voltmeter
# Description
1Negative Terminal
2Signal Connector #1
3Signal Connector #2
4Positive Terminal
5Battery State of Charge Indicator
5
2 31 4

5
Torque Rating
Power Cables
Choose the appropriate power cable size based on the system load requirements. Cables are
rated at ambient temperature of 30°C (86°F) per the table below. When connected in parallel
configuration, it is preferable for all cables to be the same length size.
Communication Cables
If your application requires communication, please connect a CAN cable to the battery signal
connector and respective system or chargers. See wiring diagram on page 7.
Copper Wire Gauge (AWG) Ampacity (A)
14 20
12 25
10 30
8 50
6 65
4 85
3 100
2 115
1 130
0 (1/0) 150
00 (2/0) 175
Item Mfg Part No. Cable Length Where to Purchase
Pack to Host T4161120008-001 0.5 meter (1.64’) Digikey
Pack to Pack M12A08MR-12AMR-SBA05 0.5 meter (1.64’) Digikey
Model Terminal Type Wrench
Size
Torque
(Nm)
M-24V60-TRX ISO M8 x 1.25 x 16mm Threaded Hole 13mm 17 ± 1

6
TE Connector P/N: T4131012081-000
Pin Definition (M-24V60-TRX)
Charging
Many types of lead acid chargers are compatible with our PROTRXion™ batteries and safely
charge in temperature ranges as shown in the table below. When choosing an intelligent char-
ger, please discuss with Inventus Technical Support on suitable o-the-shelf charger solutions.
Charger datasheets can be provided upon request.
Recommended Charge Voltage / Current
Float Charge Voltage
Pin Definition
If in doubt, please consult with
Inventus Power Technical Support
([e-mail])
on further instructions on the signal
cable connections to the host system.
Pin # Symbol Description
1VCANH CAN High for communication to the vehicle/machine
2VCANL CAN Low for communication to the vehicle/machine
3VWAKE Wake up input pin – active low to enable Discharging
4VGND Pack signal ground used to pull Wake up and Interlock low
5VINTLK Interlock input pin – active low to enable charging
6PACK_S_ID Pack series configuration ID, leave floating (Connections of
M-24V60-TRX battery are parallel only)
7VCANL_BATT CAN Low for module to module communications
8VCANH_BATT CAN High for module to module communications
Model M-24V60-TRX
Charge Voltage 28 VDC
Charge Current 30A (0.5C)
Charge Temperature (with heater) -35°C to 55°C (-31°F to 131°F)
Charge Temperature (without heater) 0°C to 55°C (32°F to 131°F)
Model M-24V80-TRX
Float Voltage 27.6 VDC

7
Module Configuration
Parallel Connection
The M-24V60-TRX battery can be connected in parallel to increase your energy requirements.
You may connect up to 15 batteries in parallel for the M-24V60-TRX battery.
Single Install Parallel Connection
Pack (-)
Signal Cable
(System)
Pack (+)
Signal Cable
(Pack to Pack)
Note: CAN lines in the battery pack DO NOT have internal termination resistance. It is
recommended to properly terminate the system and battery CAN Bus lines following the CAN Bus
termination standards. For any technical questions about properly adding termination resistance,
please contact technical support at [e-mail].
Pack (-) Pack (+)
Signal Cable
(System)

8
Wake-Up & Ship Mode
Installation
1. Remove power to the vehicle/device prior to installation of the
battery.
2. For the M12 signal connector, short pin 4 (VGND) to pin 5 (VINTLK)
to wake up battery from Ship Mode.
3. Attach negative cable from the device to the negative terminal
on the battery.
4. Attach positive cable from the device to the positive terminal on
the battery.
5. Attach M12 signal male to wire cable (T4161120008-001) only if the
host system requires CANbus communication. Connect CAN signal
cables to the TE M12 connector with 0.60 Nm [6.1 kgfcm] or less
torque in order to maintain good connection and avoid damaging the
battery. DO NOT rotate the mating connector or loosen the nut on
the battery M12 connectors to avoid damaging the battery.
Battery Modes
Press the SOC button
for 5 seconds
Wake-Up
Connect pins 4 & 5
to exit Ship Mode
Sleep Mode
Disconnect pins 3, 4 & 5
to put into Sleep Mode
Charging Mode
Connect pins 4 & 5
to enter Charging Mode
Discharging Mode
Connect pins 3 & 4
to enter Discharge Mode
12 3 4 5 6 7 8 12 3 4 5 6 7 8 12 34 5 6 7 8 12 34 5 6 7 8
TO WAKE UP THE BATTERY
TO PLACE IN SHIP MODE
We recommend to place the battery
in Ship Mode when it is not used to
prevent self-consumption current
drain and extend storage life.
Press the SOC button
for 20 seconds
Pin 1
Pin 5
INTLK
Pin 4
GND
Pin 3
VWAKE

9
LED Status Operation Mode
Heater Operation
PROTRXion™ batteries have an optional heater for each module for using during cold weather
operation. The heater power will be drawn from charger during charge mode and from the cells
during discharge mode. Always connect the charger to make sure the batteries can support
operation of the battery heaters and recharge the batteries as needed. The battery heaters will
not operate when ambient temperature is below -35°C (-31°F).
For Charging: If the ambient temperature reaches below 0°C (32°F), the battery heater will
activate to support charge mode until the battery pack temperature reaches above 5°C (41°F).
Charging will be prohibited while the heater is activated.
For Discharging: If the ambient temperature reaches below -10°C (14°F), the battery heater
will activate to support discharge mode until the battery pack temperature reaches above -5°C
(23°F).
LED Indicator Status SOC
81 – 100%
61 – 80%
41 – 60%
21 – 40%
11 – 20%
1 to 10%
Mode Wake
up Interlock Mode Name
Battery
Mode
1O
(High)
O
(High) Sleep Sleep
2O
(High)
On
(Low) Charge Normal (Charge)
3On
(Low)
On
(Low) Charge Normal (Charge)
4On
(Low)
O
(High) Discharge Normal (Discharge)