Inventus Power PROTRXion S-12V100-TRX-HD User manual

inventuspower.com
[email protected]
+1 877.423.4242
Inventus Power, Inc.
1200 Internationale Parkway
Woodridge, IL 60517
Designed & Manufactured by
PROTRXion™
Quick Start Guide
S-12V100-TRX-HD

2
PROTRXion™ Quick Start Guide
Applicable Models
Document Information
Inventus Power® and PROTRXion™ are trademarks of Inventus Power.
Copyright© 2023 Inventus Power All rights reserved.
Technical Support
If you have any technical questions regarding the PROTRXion™ battery, please contact our
technical support team at:
Phone: [phone]
E-mail: [e-mail]
Model Part No. (NMEA 2000)
S-12V100-TRX-HD (w/out heater) 59096-001
Release Date Revision Scope of Change
2023-02-23 V1.3 Minor edits to version 1 release

3
Quick Start Guide
Please read the detailed User Manual first and refer to this guide as another quick resource.
Mechanical Features
Battery Terminal Torque Rating
Before installation or maintenance of your batteries, the following equipment
is required:
• Rubber gloves
• Safety goggles or other eye protection
• Insulated Torque Wrench / Philips Screwdriver
• Voltmeter
TE Connector P/N: T4131012081-000
If in doubt, please consult with
Inventus Power Technical Support
([e-mail])
on further instructions on the signal
cable connections to the host system.
# Description
1Negative Terminal
2Lift Strap
3Signal Connector
4Positive Terminal
5Battery State of Charge Indicator
2
5
3 41
Model Terminal Type Wrench
Size
Torque
(Nm)
S-12V100-TRX-HD
ISO M8 x 1.25 x 12mm Bolt
13mm 17 ± 1
ISO M8 x 1.25 x 16mm Spare Bolt
(Use for multiple stacked ring terminal connections)

4
Wake-Up & Ship Mode
Press the SOC button
for 5 seconds
TO WAKE UP THE BATTERY
TO PLACE IN SHIP MODE
We recommend to place the battery
in Ship Mode when it is not used to
prevent self-consumption current
drain and extend storage life.
Press the SOC button
for 20 seconds
Pin 1
Pin 5
INTLK
Pin 4
GND
Pin 3
WAKE
Power Cables
Power cables are not included with the battery unless a integration kit is purchased. Choose
the appropriate power cable size based on the system load requirements. When connected in
parallel configuration, it is preferable for all cables to be the same length and wire guage. Refer
to ampacity table in User Manual when selecting power cables.
Communication Cables
Communication cables are not included with the battery unless a integration kit is purchased.
If your application requires communication, please connect a CAN cable to the battery signal
connector and respective system or chargers.
Item Mfg Part No. Cable Length Where to Purchase
Pack to Host T4161120008-001 0.5 meter (1.64’) Digikey
Battery can also receive a wake up
signal from the signal connector
by shorting pin 4 (GND) to pin 5
(INTLK) to wake up battery from
Ship Mode.
Wake-Up
Connect pins 4 & 5
to exit Ship Mode
12 3 4 5 6 7 8

5
Charging
Many types of lead acid chargers are compatible with our PROTRXion™ batteries and safely
charge in temperature ranges as shown in the table below. When choosing an intelligent
charger, please discuss with Inventus Technical Support on suitable o-the-shelf charger
solutions. Charger datasheets can be provided upon request.
Charge Voltage / Current
Pin Definition
Pin Definition (S-12V100-TRX-HD)
Note: CAN lines in the battery pack DO NOT have internal termination resistance. It is
recommended to properly terminate the system and battery CAN Bus lines following the CAN
Bus termination standards. For any technical questions about properly adding termination
resistance, please contact technical support at [e-mail].
Model S-12V100-TRX-HD
Max Charge Voltage 14.0 VDC
Charge Current 50A (0.5C)
Max Charge Current 100A (1.0C)
Charge Temperature
(without heater)
0°C to 55°C
(32°F to 131°F)
Pin # Symbol Description
1CANH_SYS CAN High for communication to the vehicle/machine
2CANL_SYS CAN Low for communication to the vehicle/machine
3WAKE Non-isolated wake up input signal used to wake the battery
from low power Sleep Mode
4GND Reference ground used to pull Wake and Interlock pins low
5INTLK Non-isolated interlock up input signal used to wake the
battery from low power Sleep Mode
6Not Connected Pin not connected.
7Not Connected Pin not connected.
8Not Connected Pin not connected.

6
Connecting the Battery
Do NOT connect in Series or Parallel. Please contact Inventus Technical Support if the system
requires more than 1 battery.
1. Remove power to the vehicle/device prior to installation of the PROTRXion™ battery.
2. Remove all other batteries from the system prior to replacing them with PROTRXion™
batteries.
3. Ensure the PROTRXion™ battery is in Ship Mode to remove power for safe install.
4. Remove the protective battery terminal covers from the terminals. Retain these covers in
the event that you need to remove or move the battery at some future time.
5. Attach the negative cable from the device to the negative terminal on the battery.
6. Attach the positive cable from the device to the positive terminal on the battery.
7. Attach M12 communication cables from battery to host system if the host system requires
NMEA 2000 communication. Connect communication cables to the M12 connector on the
battery with 0.60 Nm [6.1 kgfcm] or less torque in order to maintain good connection and
avoid damaging the battery. DO NOT rotate the mating connector or loosen the nut on the
battery M12 connectors to avoid damaging the battery.
8. If the battery charger is integrated with the device drawing power from the PROTRXion™
battery, then please follow manufacturers recommended sequence for each battery connection.
9. It is recommended to fully charge and fully discharge the battery system upon initial con-
nection to properly calibrate the SOC.
Module connections
Warning: Do not connect S-12V100-TRX-HD batteries in series or parallel. Connecting in series
or parallel exceeds the voltage or balancing limit of the integrated safety protection circuitry.
Single Install
Pack (-)
Signal Cable
(System)
Pack (+)

7
Battery Modes
LED Status
Mode Name WAKE INTLK Action Mode Description
Sleep,
(Terminals ON)
O
(Open)
O
(Open)
Disable pins 3 & 5 and
wait 5 minutes to enter
Sleep Mode
Sleep,
Terminals ON,
MOSFETs closed
Charge N/A N/A Charge current ≥500mA
to enter charge mode
Charge allowed,
MOSFETs closed
Discharge N/A N /A
Discharge current >
500mA to enter
discharge mode
Discharge allowed,
MOSFETs closed
Ship N/A N/A
Press the SOC button
and hold for 20 sec to
place in Ship Mode
Low power mode,
MOSFETs open
Shutdown N /A N/A Apply charge voltage to
exit Shutdown
Lowest power mode,
MOSFETs open
Charge Mode
Charge Current ≥500mA
to enter Charge Mode
Discharge Mode
Disharge Current > 500mA
to enter Discharge Mode
Sleep Mode
(Terminals ON)
Disable pins 3 & 5, wait 5 min
to enter Sleep Mode
12 3 456 7 8
LED Indicator Status SOC
80 – 100%
60 – 79%
40 – 59%
20 – 39%
10 – 19%
<10%