Inventus Power PROTRXion S-24V60-TRX User manual

inventuspower.com
[email protected]
+1 877.423.4242
Inventus Power, Inc.
1200 Internationale Parkway
Woodridge, IL 60517
Designed & Manufactured by
PROTRXion™
Quick Start Guide
S-24V60-TRX

2
PROTRXion™ Quick Start Guide
Applicable Models
Document Information
Inventus Power® and PROTRXion™ are trademarks of Inventus Power.
Copyright© 2022 Inventus Power All rights reserved.
Technical Support
If you have any technical questions regarding the PROTRXion™ battery, please contact our
technical support team at:
Phone: [phone]
E-mail: [e-mail]
Model Part No. (CANopen)
S-24V60-TRX (w/out heater) 58692-601
Release Date Revision Scope of Change
2022-08-01 V2.0 Version 2 Release

3
Quick Start Guide
Please read the detailed User Manual first and refer to this guide as another quick resource.
Mechanical Features
Battery Terminal Torque Rating
Before installation or maintenance of your batteries, the following equipment
is required:
• Rubber gloves
• Safety goggles or other eye protection
• Insulated Torque Wrench / Philips Screwdriver
• Voltmeter
TE Connector P/N: T4131012081-000
If in doubt, please consult with
Inventus Power Technical Support
([e-mail])
on further instructions on the signal
cable connections to the host system.
Model Terminal Type Wrench
Size
Torque
(Nm)
S-24V60-TRX ISO M8 x 1.25 x 12mm Bolt 13mm 17 ± 1
# Description
1Negative Terminal
2Signal Connector #1
3Signal Connector #2
4Positive Terminal
5Battery State of Charge Indicator
2
5
3 41

4
Wake-Up & Ship Mode
Press the SOC button
for 5 seconds
TO WAKE UP THE BATTERY
TO PLACE IN SHIP MODE
We recommend to place the battery
in Ship Mode when it is not used to
prevent self-consumption current
drain and extend storage life.
Press the SOC button
for 20 seconds
Pin 1
Pin 5
VINTLK
Pin 4
VGND
Pin 3
VWAKE
Power Cables
Power cables are not included with the battery unless a integration kit is purchased. Choose
the appropriate power cable size based on the system load requirements. When connected in
parallel configuration, it is preferable for all cables to be the same length size. Refer to ampaci-
ty table in User Manual when selecting power cables.
Communication Cables
Communication cables are not included with the battery unless a integration kit is purchased.
If your application requires communication, please connect a CAN cable to the battery signal
connector and respective system or chargers.
Item Mfg Part No. Cable Length Where to Purchase
Pack to Host T4161120008-001 0.5 meter (1.64’) Digikey
Pack to Pack M12A08MR-12AMR-SBA05 0.5 meter (1.64’) Digikey
Wake-Up
Connect pin 5 to external V+
& pin 4 to external V-
to exit Ship Mode
12 3 4 5 6 7 8
-+
Battery can also receive a wake
up signal from the signal con-
nector by connecting pin 4
(VGND) and pin 5 (VINTLK)
to a shared external voltage
source.

5
Charging
Many types of lead acid chargers are compatible with our PROTRXion™ batteries and safely
charge in temperature ranges as shown in the table below. When choosing an intelligent char-
ger, please discuss with Inventus Technical Support on suitable o-the-shelf charger solutions.
Charger datasheets can be provided upon request.
Charge Voltage / Current
Pin Definition
Pin Definition (S-24V60-TRX)
Note: CAN lines in the battery pack DO NOT have internal termination resistance. It is
recommended to properly terminate the system and battery CAN Bus lines following the CAN
Bus termination standards. For any technical questions about properly adding termination
resistance, please contact technical support at [e-mail].
Model S-24V60-TRX 2X S-24V60-TRX
connected in series
Charge Voltage 28.0 VDC 56.0 VDC
Charge Current 30A (0.5C)
Max Charge Current 60A (1.0C)
Charge Temperature
(without heater)
0°C to 55°C
(32°F to 131°F)
Pin # Symbol Description
1VCANH CAN High for communication to the vehicle/machine
2VCANL CAN Low for communication to the vehicle/machine
3VWAKE Wake up input pin – active high to enable discharging
4VGND Reference ground for Wake and Interlock pins
5VINTLK Interlock input pin – active high to enable charging
6PACK_S_ID Pack series configuration ID, leave floating when pack series
confirguration is not implimented.
7VCANL_BATT CAN Low for module to module communications
8VCANH_BATT CAN High for module to module communications

6
Connecting the Battery
1. Remove power to the vehicle/device prior to installation of the PROTRXion™ battery.
2. Remove all other batteries from the system prior to replacing them with PROTRXion™
batteries.
3. Remove the protective battery terminal covers from the terminals. Retain these covers in
the event that you need to remove or move the battery at some future time.
4. Attach the negative cable from the device to the negative terminal on the battery.
5. Attach the positive cable from the device to the positive terminal on the battery.
6. Attach M12 communication cables between batteries if more than one battery and from
battery to host system if the host system requires CANbus communication. Connect com-
munication cables to the TE M12 connector on the battery with 0.60 Nm [6.1 kgfcm] or less
torque in order to maintain good connection and avoid damaging the battery. DO NOT
rotate the mating connector or loosen the nut on the battery M12 connectors to avoid dam-
aging the battery.
7. If the battery charger is integrated with the device drawing power from the PROTRXion™
battery, then please follow manufacturers recommended sequence for each battery connection.
Please contact Inventus Technical Support if the system requires more than 10 batteries.
Module connections
The S-24V60-TRX battery can be connected in series or parallel to increase your energy re-
quirements. You may connect up to 6 batteries in parallel and up to 2 batteries in parallel for
the S-24V60-TRX battery.
Single Install Parallel Connection Series Connection
Pack (-)
Signal Cable
(System)
Pack (+)
Signal Cable
(System)
Pack (+)
Pack (-)
Signal Cable
(Pack to Pack) Pack (+)
Pack (-)
Signal Cable
(Pack to Pack)
Signal Cable
(System)
Power Cable
(Pack to Pack)

7
Battery Modes
LED Status
LED Indicator Status SOC
81 – 100%
61 – 80%
41 – 60%
21 – 40%
11 – 20%
1 to 10%
Mode Name VWAKE VINTLK Action Mode Description
Sleep,
(Terminals
ON)
O
(Low) N /A
Disable pin 3 and wait 5
minutes to enter Sleep
Mode
Sleep,
Terminals ON,
MOSFETs closed
Charge N/A N /A Charge current ≥500mA
to enter charge mode
Charge allowed,
MOSFETs closed
Discharge N/A N /A
Discharge current >
500mA to enter
discharge mode
Discharge allowed,
MOSFETs closed
Ship N/A N/A
Press the SOC button
and hold for 20 sec to
place in Ship Mode
Low power mode,
MOSFETs open
Shutdown N /A N/A Apply charge voltage to
exit Shutdown
Lowest power mode,
MOSFETs open
Charge Mode
Charge Current ≥500mA
to enter Charge Mode
Discharge Mode
Disharge Current > 500mA
to enter Discharge Mode
Sleep Mode
(Terminals ON)
Disable pin 3 & wait 5 min
to enter Sleep Mode
12 3 4 56 7 8