inVue PL401 User manual

1
Smart Lock
Showcase Lock
PL401

2 3
Overview
Review entire instruction guide before starting installation.
Instructions are intended for single swing-out panel door
applications.
Lock & Cabinet Specification
The Showcase Lock is designed primarily for wood
cabinets with glass swing-out doors. The lock can also
be affixed to wood or metal doors. Panel door thickness
can range from 4.8 mm – 6.35 mm (0.19” – 0.25”). Wall
thickenss of the cabinet structure must be greater than
12.7 mm (0.5”).
System Components
1. Showcase Lock (PL401)
2. Base Plate & Base Plate Template (included)
3. Alcohol Wipe (included)
4. IR2 Key (PK4400)
Tool Requirements
1. Pencil
2. Power Drill and Bit
3. Small Router/Dremel Tool
4. Phillips #1 Screwdriver
Showcase Lock
PL401
Base Plate
(Included with PL401)
IR2 Key
PK4400

4 5
Determine location of lock. Align template with front
of glass and mark drill holes and routed pocket to as-
semble lock base.
Note: Illustrations below shows top view of cabinet.
Tip: Base plate and lock should be positioned close to
swing-out end of door panel. Base plate template should be
positioned no further forward than front edge of cabinet.
1
Glass
Template
Front of Cabinet
Base Plate
Place template 0 mm - 25 mm (0” - 0.98”) from edge of glass.
LOCK ASSEMBLY
Lock should be positioned on swing-out end of panel door
(opposite hinges).
Note: Illustrations in this guide are for installations with lock positioned
on left bottom corner of panel door. Instructions can be inverted if lock
is positioned on different corner.
Hinge
Hinge

6 7
Use router tool to route pocket a minimum depth of
12.7 mm (0.5”). Use a 2 mm (0.08”) drill bit for 3 screw
holes. Caution: Do not drill holes through cabinet
walls.
2
Screw Holes
2 mm (0.08”)
Screw Holes
2 mm (0.08”)
Pocket
12.7 mm (0.5”)
Attach base plate to cabinet with 3 wood screws pro-
vided and a screwdriver. Bottom of base plate should
be flush with flat surface of cabinet. If not flush, detach
base plate and remove more wood material from rect-
angular pocket.
3

8 9
Wipe front of panel with alcohol wipe where you intend
to mount lock. Allow alcohol to air dry for a mini-
mum of 5 minutes or dry alcohol with lint free cloth
before moving to step 5.
4Slide lock body onto glass panel. Close glass panel
and test fit lock body into lock base. Confirm proper fit/
alignment.
5
Lock BodyLock Base
STOP!
WAIT 5 MINUTES!

10 11
Lightly hold lock body in position and remove
numbered tabs in order (#1 then #2). Press lock against
glass panel for at least 10 seconds.
6Test lock to confirm proper function. Use IR2 Key to
lock/unlock installation (see page 12).
7
Tab 1
Tab 2

12 13
LOCK OPERATION USING IR2 KEY
Position IR2 Key against lock, push button and wait for “beep”
before removing key. Lock and unlock cabinets several times to
ensure proper operation.
IR2 Key must be charged
and activated. See IR2 Key
instruction guide.
Hold until you get a
confirmation “beep.”
Note: If double “buzz,” an
error has occurred. Unlock,
ensure cabinet is fully
closed and try again.
Locked
“BEEP”
LOCK STATUS INDICATORS
Locked
Unlocked
Error (not fully locked)
Note: Unlock lock. Confirm
no obstructions. Fully close
cabinet and try again.

16
© 2013 InVue Security Products Inc. All rights reserved.
InVue is a registered trademark of InVue Security Products.
SD0167 Rev0 05/06/13
www.invuesecurity.com
Corporate Office (North America) // 704.752.6513 •888.55.INVUE
Europe, Middle East & Africa // +31.23.8900150
Asia Pacific // +852.3127.6811
Latin America // +52.55.9000.3957