inVue LL301 User manual

For technical assistance call
1
NA / LATAM // 704.752.6513 •888.55.INVUE
EMEA // +31.23.8900150
APAC // +852.3127.6811
LIVE Cam Lock LL301
5Place the shaft adapter over the
shaft on the lock body. Ensure that
it is correctly oriented to t into
the hole in the xture.
2Determine the lock mounting orientation.
OrOr
4Use the provided alcohol wipe
to clean the area where the lock
body will be mounted. Allow it to
dry completely.
1Optional:
For ease of installation, use an
Installer Key (if you have one)
to unlock the lock. If using the
Installer Key in a lock with the
battery tabs in place, it will pause
the lock in an unlocked state.
3a Optional Security Screw
Installation:
If desired for additional stability, a
M4 screw can be used to further
secure the lock to the drawer.
From the center of the hole,
measure 4 1/8 inch (104.77mm).
Make a mark in line with the hole.
4 1/8in4 1/8in
104.77mm104.77mm
3b Drill a hole in the drawer face with
a 3/16 inch (or 5mm) drill bit. 3c Once the lock body is installed onto the drawer, insert and
tighten the M4 screw into the
screw hole at the bottom of the
lock body.

For technical assistance call
2
NA / LATAM // 704.752.6513 •888.55.INVUE
EMEA // +31.23.8900150
APAC // +852.3127.6811
LIVE Cam Lock LL301
8Insert the shaft through the hole
in the drawer. Press the lock body
against the surface for at least 10
seconds.
Note: If using the optional security
screw, insert and tighten the M4
screw through the drilled hole
(step 3c).
7Peel the clear liners from the 2 adhesives on the lock body. 6Insert and tighten the 2 small screws to secure the shaft adapter.
10 Thread the nut onto the shaft. 9Place the lock washer over the
shaft. 11 Use a wrench to tighten the nut.

For technical assistance call
3
NA / LATAM // 704.752.6513 •888.55.INVUE
EMEA // +31.23.8900150
APAC // +852.3127.6811
LIVE Cam Lock LL301
1313 Place the cam arm interface adapter onto the shaft to determine the direction the turn of the handle. Flip the cam arm interface adapter over (as shown above) to toggle
between left and right hand rotation to open.
OrOr
12 Bend the prongs on the lock
washer over the nut to prevent it
from loosening.

For technical assistance call
4
NA / LATAM // 704.752.6513 •888.55.INVUE
EMEA // +31.23.8900150
APAC // +852.3127.6811
19 Open the InVue LIVE Access app
and enter your login credentials.
Note: Your Passcode is the same
as your OKM User PIN.
21 Tap the lock knob with the NFC
antenna of the device being used.
The lock will unlock and relock
within 4 seconds.
20 If prompted, select the site where
the lock has been installed.
LIVE Cam Lock LL301
18 Pull the battery tabs.
17 Use a wrench to fully tighten. 16 Thread the supplied nut onto the
shaft.
14 Place the original hardware back
onto the shaft.
Note: This applies to both double-
throw locks and single cam arms.
15 Place the washer over the shaft.

For technical assistance call
5
NA / LATAM // 704.752.6513 •888.55.INVUE
EMEA // +31.23.8900150
APAC // +852.3127.6811
LIVE Cam Lock LL301
27a27a Lock Activation Using NFC:
Open the InVue LIVE Access App
on your smart device. Tap your
device against the round panel on
the lock. Once conrmed by the
App displaying “unlocked” and the
LED ashing green.
26b26b You will have several seconds to
turn the knob to unlock and open.
If the LED on the lock ashes red
before the lock is opened, it will
need to be unlocked again.
27b27b You will have several seconds to
turn the knob to unlock and open.
If the LED on the lock ashes red
before the lock is opened, it will
need to be unlocked again.
26a26a Lock Activation Using OneKEY:
Place a charged and coded
OneKEY against the lens on the
lock and press the button the Key.
The LED on the Key and the lock
will ash green.
25 Click “Save” once the lock
description elds have been lled
out.
24 Assign the device to the
appropriate Zone in your store or
site.
Note: Zones are created in Access
Manager
23 Rename the device and enter an
optional description if desired.
22 Click on the “Update Device
Settings” link to modify the Device
Name, Description, or Zone to
complete the enrollment.
Note: You must have the “Manage
Devices” permission to see and
access this link.

For technical assistance call
6
NA / LATAM // 704.752.6513 •888.55.INVUE
EMEA // +31.23.8900150
APAC // +852.3127.6811
LIVE Cam Lock LL301
31 Battery Replacement Steps:
Place a magnet key near the end
of the battery panel on the lock.
Note: Even with low batteries
the lock will still function with a
OneKEY.
3232 Remove the battery panel from the
lock.
30b30b You will have several seconds to
turn the knob to unlock and open.
If the LED on the lock ashes red
before the lock is opened, it will
need to be unlocked again.
30a30a Lock Activation Using Device
Camera: Open the InVue LIVE
Access App on your smart device
and toggle to the “Camera Scan”
screen. Center the barcode in the
viewnder. Once conrmed by the
App displaying “unlocked” and the
LED ashing green.
29b29b You will have several seconds to
turn the knob to unlock and open.
If the LED on the lock ashes red
before the lock is opened, it will
need to be unlocked again.
29a29a Lock Activation Using Scanning
Device: If your smart device has
a built in barcode reader, aim and
scan the code on the front of the
lock while the InVue LIVE Access
App is open. Once conrmed by
the App displaying “unlocked” and
the LED ashing.
28b28b Remove the panel to reveal the
barcode.
28a28a Using the 2D Barcode:
Insert a thin edged tool into the
small notch between the lock body
and the round plate.

For technical assistance call
7
NA / LATAM // 704.752.6513 •888.55.INVUE
EMEA // +31.23.8900150
APAC // +852.3127.6811
LIVE Cam Lock LL301
Warning – Fire, Explosion,
Burn Hazard:
InVue recommends the use
of Great Power or Energizer
CR123A batteries. Use of other batteries,
mixing of used and new or different
battery chemistries may present a risk
of leakage, re, explosion and serious
personal injury. Do not ingest, recharge,
misuse, short circuit, improperly store
or discard, disassemble or heat above
212°F (100°C). Keep away from children.
!
3434 Slide the battery panel back into
place.
3333 Replace the old batteries with new
CR123A non-rechargeable lithium
batteries.