iPuray BRT-410 User manual

Product Description of BRT-410 Page 1of 5
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
Timer Switch with Daily Multiple Period Settings
(No Neutral Required)
Model #：BRT-410
Features:
BRT-410 is the most advanced timer switch. It is controlled by a micro controller unit and has very
accurate timing capability. It is designed for easy installation and retrofit, directly fit into standard
wall box where both hot wire and neutral wire are present.
Two buttons for easy operation and controls two loads;
Hidden panel of 9 keypads for setting up timer to prevent inadvertent changes;
Up to 16 preset timing periods with precise On and Off time each day;
LCD display showing the current clock time, timing period #, and the current status of the
switch;
Good for all kinds of loads (Resistive, inductive, and capacitive);
ABS-V0 flame resistance material; and
Classical 86 series design and high quality build.
Front View, Back View, and Hidden Panel
Fig. 1 and Fig. 2 show the front view and the back view of the wall mount unit of BRT-410 timer
switch respectively.
Fig. 1 Front View Fig. 2 Back View

Product Description of BRT-410 Page 2of 5
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
As shown in Fig. 1, BRT-410 timer switch has an LCD display and Two On/Off buttons on the
front. The LCD display shows the current time and the current status of the switch. The On/Off
buttons are used for turning on or turning off two loads respectively. BRT-410 timer switch also
has wiring terminal blocks on its back.
When the On/Off button is pressed,
The display shows On and the load #, and the load will be turned on immediately; and
When the On/Off button is pressed again,
If there is no timing period being set, the load will be turned off immediately and the display
will show Off and the load #, and;
If there is timing period being set, the load will be turned on automatically during the preset
timing period. Press the On/Off button will cancel the timing operation and turn off the load
immediately.
Fig. 3 Hidden 9 Keypad Panel
As shown in Fig. 3, the front plate can be flipped down from the top edge. A 9 keypad panel
hidden behind the front plate is used for setting up the timer. Please refer to “BRT-410 Timer
Switch Setup” for details.
Specification Parameters:
Input Voltage
220～240V(50Hz/60Hz)
Operation
Environment
No-condensation 20-90% RH，
-20℃～55℃
Wattage
1000W/Load
Load type
All Types*
Mounting Hole
Spacing
60mm
Matching
Box
75mm x 75mm x 50mm
Wall Mount
Unit Dimension
86mm x 86mm x 38mm
Wall mount
Unit Weight
125g

Product Description of BRT-410 Page 3of 5
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
Wiring Diagram and Installation Guide:
BRT-410 timer switch requires both hot wire and neutral wire for installation:
Hot wire (ACL): Coming from the power line with 220V;
Neutral wire (ACN): Usually coming with the hot wire; and
Load wires: Going to the load.
Fig. 4 Wiring Diagram of Wall Mount Unit
Warning: Please make sure power is turned off before starting installation!
Fig. 4 shows the wiring diagram and Fig. 5 shows the step-by-step installation instructions.
Fig. 5 Installation Guide of Wall Mount Unit

Product Description of BRT-410 Page 4of 5
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
There are three easy steps:
Step one: Use a screwdriver to pry off the front plate in position A;
Step two: Wiring according to the diagram and the labelled ports of the switch; and
Step three: Install screws and front plate.
BRT-410 Timer Switch Setup:
1. Power the switch with 220 voltages: following the wiring diagram and Installation Guide.
2. Set up Clock Time: Press and hold the SET button until the displayed hours flash. Press –
or +to adjust the hours. Press the SET button again, the displayed minutes will flash, and
then press – or +to adjust the minutes. Press the SET button again, the displayed day of the
week will flash, and then press – or + to adjust the day. Finally, press and hold the SET button
to save the settings.
3. Set up Timing Period for the First Load:
3-1. Set up the “On” time: Press and hold the Ibutton until the display shows “ON” and
“01” and the displayed hours flash. Press – or + to adjust the required “on” hours. Press SET
button, the displayed minutes flash, and use – or + to adjust the required “on” minutes; and
3-2. Set up the “Off” time: Right after setting up the “on” time, press SET button again,
and the display shows “OFF” and “01” and the displayed hours flash. Press – or + to adjust
the required “off” hours. Press SET button again, the displayed minutes flash, and use – or +
to adjust the required “off” minutes.
(During setup step 3-1 and 3-2, hold the – or + will adjust the digits quickly.)
At this point, both the “on” time and the “off” time have been set up for timing period #1.
3-3. Set up more timing periods: Right after setting up the first timing period, pressing "◁"
or "▷" will enter setting up other timing periods. Follow the procedures above to set up the
timing periods accordingly. Up to 16 timing periods can be set up.
Finally, press and hold the SET button to save the settings or the settings will be saved
automatically if there is no keypad operation for 15 seconds.
4. Set up Timing Period for the Second Load:
Pressing and holding the II button will start setup for the second load. Follow step 3-1
through 3-3 to set up its timing periods accordingly.

Product Description of BRT-410 Page 5of 5
Shenzhen Asia Bright Industry co., Ltd., Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China.
www.a-brt.com. [email protected].
© 2015 All rights reserved. Subject to change without notices.
5. Change or Delete Timing Period: If you want to delete a timing period, follow the
above steps to change the settings to “--:--”.
Applications:
BRT-410 timer switch is used for automatically turning on and/or turning off various loads such as
fans, lights, appliances, or other kinds of electrical equipment. They are perfect for saving energy
and bringing convenience and safety to our daily life and work.
They have wide applications at various locations such as homes, schools, laboratories, hospitals,
offices, etc. The typical application scenes include:
Schools: Automatically ring the bells according to a fixed timetable to relieve manual
intervention.
Hospitals or Laboratories: Automatically turn on and turn off UV disinfection equipment to
isolate operators from harmful UV exposure.
Farms: Automatically turn on or turn off breeding equipment or lighting equipment for
animals.
How to Order:
Please contact us: Shenzhen Asia Bright Industry Co., Ltd
Building 10, Asia Industrial Park, Gangtou, Bantian, Shenzhen, China
Tel: [phone] 89748211 89748345
Fax: [phone] [phone]
Email: [e-mail] Website: www.a-brt.com