Iridium 113776 User manual

iridium
Stage Studio Manual Zoom 12-55°
Product Code: 113776

For your safety, read this manual carefully before first use

1
1. Introduction
instructions for use and keep it for future reference if necessary. It contains
Please comply strictly with it.
*This product meets the CE & ROHS standard.
Thank you for purchasing this product. Before using this device read this
important information on the use and installation of the product.
This product can be controlled in DMX 512 format.

2
2. Safety instructions
• Do not open this product. Risk of electric shock
• Keep all flammable materials at least 50 cm away from the projector
• Never stare at the light source when the product is on
• Always use a safety sling in case of snagging
•Caution: during use and afterwards, the chassis is very hot –
• This device is not intended for outdoor use, or in humid or dusty
environments.
risk of burns.
ATTENTION
• Never use the device if there is visible damage to the chassis or the
power cable.
• Install this projector in a sufficiently ventilated space, with a minimum
distance of 50 cm from adjacent surfaces

3
protected upstream.
•Made of fire-resistant nylon and aluminum alloy.
•The maximum ambient temperature of use is 40°C.
•Adjustable dimming curves
•Silent ventilation.
•Flicker free
Do not use this device if the ambient temperature is higher.
•Delivered with flow break
•Do not connect this device to a dimming unit
•Control to DMX 512 standard
•Connect this device to an earthed electrical source, and
•Suspension bracket
Features
3. Description

4
The stand must be able to support 10x the weight of the device
This device can be mounted on a structure.
qualified according to the rules of the art.
Any suspended installation must be implemented by personnel
Structural assembly
equipped without deformation after one hour.
Dimensions
4. Installation

on a general context cannot explain.
maximum load on a power line must not exceed 8
Only use specific 110 Ohm cable to make the connections
This device automatically adapts to voltages 110-240 V AC. There
specific criteria, and particular conditions, that this manual, based
DMX512 connection
Note that implementation in certain locations may respond to
Food
installation of the places concerned.
a single DMX line.
Amps.
Always make sure you know the special conditions
DMX. It is recommended not to exceed a maximum of 20 devices on
5

6
5.Operation
Press the Menu key until one of the parameters is displayed
DMX address setting
1st Menu
0-512
Control panel
2nd Menu
DMX address
Menu
Action
DMX
following:
Value

Sun
0-255
Protective temperature
0-255
ÿWhen the temperature of the device exceeds the programmed protection temperature,
the device automatically limits its power by 30%, until it returns to normal values.
CH03
Strobe
0-255
0-255
Temperature
ÿThe display goes into standby mode after 30 seconds without
0-255Channel
Manual
YES/NO
Notes:
Reset settings
T.080
Dimmer
0-255
CH01
Temperature
0-255
STO
C.000
operation.
Strobe
DimmerFine
Reset
CH02
D_F
ÿWhen “!” is displayed, flashing, no DMX signal detected.
Use the Up and Down keys to navigate, and Enter to validate the choices
Dimmer Fine, 5% adjustment
margin
Dimmer
factory
7

8
0-10 Strobe off, 11-255 strobe frequency
CH3 0-255
(slow to fast)
Strobe
Channel
0-255 5% dimmer adjustment
0-255 Dimmer 0-100%
1 channel mode
0-255 Dimmer 0-100%
DimmerFi
CH1
Dimmer
Value
CH1
Value
Function
Channel
CH2
CH2
DimmerFi
Channel
Function
DMX modes
Dimmer
2 channel mode
born
Function
Dimmer
0-255 Dimmer 0-100%
Function
Function
CH1
0-255 5% dimmer adjustment
born
Function
Value
3 channel mode

9
6. Fuse replacement
7. Technical characteristics
200W
IRC:
DMX Channels:
Only use a fuse strictly equivalent to the original one if replacement is necessary.
Always disconnect the power
113776
150mm Fresnel
STM32 control chip, DMX512 signal
LED source:
16 Bit / 0-100%
Consumption:
Reference:
200W COB Citizen led
>90
IP rating:
Beam angle:
Control:
before any electrical intervention on the device.
100 - 240V AC
IRIDIUM Stage Studio Manual Zoom Fresnel
4-button LCD
Color temperature: 3200K
1CH/2CH/3CH
Food:
Lens:
12°ÿ55°
Designation:
Frequency:
IP20
Display:
50/60Hz
Gradation:

Packaging:
1M
5.8kgs
Weight:
Dimensions:
illuminated object
Minimum distance to
360x270x427mm
-15ÿÿ35ÿ
1 pc/box
Packaging dimensions:
Operating
temperature.:
420x330x360mm
1

IMPORTER
B&K LUMITEC
ZI – 2 Rue Alfred Kastler – 67850 Herrlisheim – France
www.bklumitec.com