Iridium 113777 User manual

iridium
Stage Profile
Product Code: 113777

2

CONTENT
1. Introduction
2. Safety instructions
Proper Use
Care
3. Description
Products features
Overview
4. Installation
Overhead rigging
DMX512 connection
Power Input
5. Operation
Control board
DMX modes
6. Replacing the fuse
7. Focus
8. Technical specification
3

1. Introduction
Dear customer, thank you for deciding to purchase our product. The product fulfils the requirements of eective European
and national guidelines. To maintain the condition of the product and to ensure safe operation, you - as the user - must
observe the product notes and the operation manual!
They contain important information for the start-up and handling. It is important, therefore, that these documents are
archived carefully for referring to information at a later stage.
2. Safety Instructions
We are not responsible for any property damage or personal injury caused by failure to observe these product notes and
manual, improper handling or unauthorised modifications.
It can only be installed by a qualified electrician. Make sure that the item has not been damaged during transport before
putting the light into operation. It may not be operated if there are any damages to electrical parts. The luminaire may
only be operated completely with its protective cover. It may only be operated once removed from the packaging. The
type plate must not be removed.
The connection lines in the building must be disconnected before installation and secured against being switched back
on. For this, trip the corresponding fuse switch in the building installation.
Make sure the electrical specifications for the connection lines correspond with the specifications given on the nameplate
of this product. We recommend that you protect the product with a residual-current-operated protective device.
Follow all installation regulations applicable at your location. Make sure that the cables and plugs are not subject to
tension or torsional forces and do not bend the cables. Protect all cables and insulation against possible damages.
Output lines should be laid separately and spaced apart from other lines. The power supply cables and the lamp feeders
must not cross each other. Do not allow the product to come into contact with extreme heat or naked flames. Use the
supplied fastening material only when it is suited for the installation background. The product must not be covered with
objects (decorations) or thermally insulating coverings /similar materials. Before disposal of the packaging material
make sure that all components are removed. Keep packaging material away from the reach of children and pets. The
packaging contains small parts that may be swallowed by children.
Proper Use
This product is only intended for lighting purposes and may only be operated on normal or non-flammable surfaces. The
use can be done in indoor/outdoor areas.
Make sure that the surface is suitable for permanently and reliably taking the weight of the light.
Care
Repairs may only be carried out by a qualified electrician. If the external flexible cable or cord of this luminaire is
damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in
order to avoid a hazard. Disconnect the entire product from the mains first and allow it to cool down before cleaning or
maintaining. Use a dry or slightly moistened cloth for cleaning. Never use any chemicals, flammable cleaning agents or
abrasives. These may cause damage to the surface coating and/or the insulators.
4

3. Description
- Made by fire-resistant Nylon material and Aluminum which makes the lamp more lighter
- Good performance of cooling system with the quiet fan
- DMX controlled operation, possible work with any commercial DMX512 controller
- Rail-type hanging bracket, bracket position can be adjusted
- Dierent dimmer curves and dimmer speed adjustable
- Flicker free projection
- Rotatable barn doors, color filter optional
- Ready for connection with power cord with safety-plug
4. Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Overhead rigging
The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for 1hour
without any harming deformation. The installation must always be secured with a secondary safety attachment. This
secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main
attachment fails. The operator has to make sure that safety-relating and machine-technical installations are approved
by an expert and before taking into operation for the first time and after changes .
Please note: for overhead rigging in public or industrial areas, a series of safety instructions have to be followed that
this manual can only give in part.
DMX512 connection
If you are using controllers with this occupation, you can connect the DMX output of the controller directly with the DMX
input of the first fixture in the DMX chain.
Building a serial DMX chain: Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next
fixture. Always connect one output with the input of the next fixture until all fixtures are connected.
For better signal receival, a signal amplifier suggest to be used for each 20 fixtures.
Power input
This device has an auto-switching power supply work with input voltage range of 100-230V AC, 50/60Hz. Link up to the
maximum 8A, Do not exceed this.
5

5. Operation
Control board
Press the Menu until one of the following had been displayed:
Menu
Menu 1 Menu 2 Value Description
DMX Addr. 1-512 DMX512 address
Channel
CH01 0-255 Dimmer
CH02 0-255 DimmerFine, 5% brightness increased
based on 01CH
CH03 0-255 Strobe
Manual
Dim 0-255 Dimmer
D_F 0-255 DimmerFine
STO 0-255 Strobe
Reset YES/NO Recover to manufactory default
Temperature C.000 0-255 Current temperature
T.080 Protecting temperature
Use ‘Up’ and ‘Down’ button to select your desired operation, press ‘Enter’ to set all function
Notes:
» When there’s a flickering ‘!’ sign appeared, means no signal input for the fixture.
» No operation within 30seconds, LCD display will enter into Screen protection mode automatic.
»When the current temperature is higher than the protecting setting temperature, 30% of power consumption will be
deducted slowly; Power consumption will be coming to normal when the temperature gets to normal.
6

DMX Modes
DMX512 Channel table
1 Channel Table
Channel Value Rate Function
CH1 Dimmer 0-255 Dimmer, brightness from 0%
2 Channel Table
Channel Value Rate Function
CH1 Dimmer 0-255 Dimmer, brightness from 0%
CH2 DimmerFine 0-255 Brightness micro adjustment
3 Channel Table
Channel Value Rate Function
CH1 Dimmer 0-255 Dimmable,brightness from 0%
CH2 DimmerFine 0-255 Brightness micro adjustment
CH3 Strobe 0-255 0-10 Strobe o, 11-255 Strobe frequency(from
slow to fast)
6. Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating. Before replacing the
fuse, unplug mains lead.
Procedure:
Step1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
7. Focus
The objective lens cylinder is usually shrinked before leaving factory, after connect the projector to the mains, user may
loose the screws and pull out the lens cylinder, till the white light output circular is clearly presented, locking tightly the
two screws again.
When the projection distance is changed, user can follow previous operating steps, and focus the projector.
7

8 Technical specifications
Item Number: 113777
Product name: IRIDIUM Stage Profile
Power Consumption: 200W
Voltage: 100 - 240V AC
Frequency: 50/60Hz
Light Source: 200W COB Citizen led
Lens: 6pcs Special imaging glass optical lens
Color temperature: 3200K
CRI: >90
Beam Angle: 19°
Dimming Range: 16bit smooth dimming 0-100%
DMX Channel: 1CH/2CH/3CH Optional
Control system: STM32 control chip, DMX512 signal
Display Screen: 4-Button LCD Screen
IP Rating: IP20
Min. Distance to Illuminated object: 1M
Ambient Temp.: -15°C - 35°C
Product size: 538x270x427mm
Weight: 10kgs
Packing: 1pc per carton
Packing size: 665x330x360mm
8

IMPORTER
B&K LUMITEC
ZI – 2 Rue Alfred Kastler – 67850 Herrlisheim – France
www.bklumitec.com