Iridium LED WASH PRO 44WS 44x20W User manual

LED WASH PRO
44WS 44x20W
Importateur
GEMAR – LUMITEC
13 Rue Alfred Kastler
67850 HERRLISHEIM
CODE 104260

Press “ENTER” button and then “UP” or “DOWN” button until “SET UP” is showed.
Press “ENTER” button and then “UP” or “DOWN” button until “Wirless rel” is
displayed, press ENTER button. Then press DMX Mode is ok.
Then, until Green wireless signal is displayed. Then Wireless DMX connected
success.
About the condition of wireless signal, Green represents the successful setting, while
red represents the signal is unsuccessful.
Press “ENTER” button and then “UP” or “DOWN” button until “Wirless rel” is showed.
Press “ENTER” button and then “UP” or “DOWN” button until “press +/-” is
displayed, press “UP” or “DOWN” button, long press “UP” or “DOWN” button about
5-6 seconds. Until “Initialization” to “Release finish” is displayed. It means release
signal successfully.
Wireless connection
Master / Slave connection
Release wireless DMX signal
DMX address: 001
ID address: 01
DMX OUTPOWER
DMX IN POWER
3
14
Packaging:Thanks for your purchasing the LED WASH PRO 44WS. All the lights have
been checked and are in excellent operating condition. Please check the shipping carton
first,because there may be damage occurred during the shipment.Then check the lights
carefully and be sure that the lights is intact and works normally.In the event damage has
been found, spare parts are missing or the lights works abnormally,please contact us for
further instructions. And please don’t return the lights to the dealer before contacting us.
Introduction:The LED WASH PRO 44WS. has three operating modes:DMX mode, Auto
mode and Master/Slave mode.And the lights has five DMX modes,including channel
2,channel 3 , channel 4, channel 9 and channel 12.There are twenty-one built-in Auto
programs and you can see twenty-one kinds of shows when you open the Auto
mode.Meanwhile, you can edit your desired Auto program in “EDIT” menu.In addition,
you can connect several pieces of lights in DMX mode and set one in Auto mode, and the
others in Master/Slave mode.And then all the lights in Master/Slave mode will run
following the one in Auto mode.Using fog or special effect smoke,you can see better
showing effect.
Warning!
1.Don’t expose the lights to rain or moisture,for the sake of preventing the risk of
electrical shock or fire.
2.Don’t look directly at the opening lights all the time,or it may damage your eyes.
Introduction
Product Overview
Connection

POWER IN DMX IN MENU ENTER UPDOWN DMX OUT POWER OUT
586.93
492.91
13
CABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on
the other end.
3-PIN TO 5-PIN CONVERSION CHART
3-PIN TO 5-PIN CONVERSION CHART
Note! If you use a controller with a 5 pin DMX output connector, you need to use a 5 pin
to 3 pin adapter. The chart below details a proper cable conversion:
caution:Do not allow contact between the ground and the fixture’s chassis ground. Grounding the
ground can cause a ground loop, and your fixture may perform erratically. Test cables with an ohm
meter to verify positive pole and to make sure the pins are not grounded or shorted to the shield or
each other.
DMX connector configuration
GROUND
Conductor
Ground/Shield
Data ( - ) signal
Data ( + ) signal
Do not use
Do not use
3 Pin Female (output)
Pin 1
Pin 2
Pin 3
5 Pin Male (Input)
Pin 1
Pin 2
Pin 3
Do not use
Do not use
Mechanical Specification

209.91
333.5
ACCESSORIES

Features
DMX 9 channel
channel
1
2
3
4
value
0 - 255
0 - 255
0 - 255
0 - 255
function
Master dimmer
Strobe
red
green
50 - 255blue
60 - 255white
70 - 255Dimmer speed
80 - 255auto/ customer effect
90 - 255speed
DMX 12 channel
channel
1
7
3
4
value
0 - 255
0 - 255
0 - 255
0 - 255
function
Master dimmer
Dimmer speed
red
green
50 - 255blue
60 - 255white
2
8
9
10
11
12
0 - 005Strobe open
006 - 010 Strobe closed
011 - 033 Plus Random, slow -> fast
034 - 056 Ramp up Random, slow -> fast
057 - 079 Ramp down Random, slow -> fast
080 - 102 Random Strobe Effect, slow -> fast
103 - 127 Strobe Break Effect, 5s.....1s(Short burst with break)
128 - 250 Strobe slow -> fast < 1Hz - 20Hz
251 - 255Strobe open
0 - 25572 color
0 - 25511 white
0 - 255auto effect
0 - 255speed
0 - 255ID
OPTICS
● Light Source: 44*20W, 4 in 1 RGBW LEDs
● Lens: 20° , 40°
ELECTRICAL
● Power consumption: 800W
● Voltage: 190-264V 50/60Hz
CONTROL
● DMX channels: 2, 3, 4, 9 & 12 CH
● Run Mode: DMX 512 /Master Slave/Auto Run
● Built-in Effect: color mixing, variable color chasing,
strobing and fading.
● Maximum 66 ID setng for easy separately control
● Wireless DMX from Sweden
SOFTWARE
● 10 internal programs and 10 customerize programs
● 4 different dimming curve
● 11 kinds of color temperature white
● Smart temperature control
● Working time record
PHYSICAL
● Material: Aluminum body
● TFT displayer with four buttons
● Key lock for buttons
● IP65
● Temperature: -40℃~50℃
● N.W: 13.5 KG
● G.W: 14.5 KG
● Dimensions: 575 x 210 x 334 mm

6
DMX control mode
Displayer introduction
DMX 3 channel
channel
1
2
3
value
0 - 255
0 - 255
0 - 255
function
Hue
Saturation
Value(brightness)
DMX 2 channel
channel
1
2
value
0 - 255
0 - 255
function
72 color
11 kinds of white
DMX 4 channel
channel
1
2
3
4
value
0 - 255
0 - 255
0 - 255
0 - 255
function
red
green
blue
white
10
1. DMX means the light is in the DMX mode.Similarly,SLAVE means the light is in
the SLAVE mode.
2. The color of the point shows the condition of signal transmission. Green
represents the good condition, while red represents the signal is interrupted.
3. The item shows the working temperature of the light.When the working
temperature exceeds the max temperature,the color of the letters and number will
change from white to yellow.
4. This item shows the menu you selected.
5. This item shows the condition of key lock. “Key lock open” means the key lock is
open.And “Key lock off” means the key lock is close.
6. The color of the point shows the condition of wireless signal. Green represents
the good condition, while red represents the signal is interrupted.

DMX Address
ADDRESS
001
ADDRESS
512
Release +/-
Factory Reset up down up down
Wireless
ON
OFF
ON
30
OFF
5s
OFF
1-66
CURV1
CURV4
0
255
70°C
600Hz
1200Hz
2400Hz
4800Hz
9600Hz
info
RDM UID 4453:05d9ff35
Hardware Var V1.0
Software Ver V1.0
Working time 0h-0m
Set up
LCD BLACK
Key Lock
ID Number
Dimmer Curve
Rate
Dimmer All
Max Temp
9
Programme Menu
AUTO-In this menu, you can select your desire AUTO mode and adjust the running speed.
1. Press “ENTER” button and then UP or DOWN button until “AUTO” is showed.
2. Press “ENTER” button, and “SPEED” or “AUTO MODE” will be showed. Then press ENTER,and
you can see two items as below:
1) SPEED - You can select your desired speed in this menu.
2) AUTO MODE - You can select your desired auto mode in this menu.
CUSTOMER-In this menu,you can select the AUTO program edited in the “EDIT” menu.
1. Press “ENTER” button and then UP or DOWN button until “CUSTOMER” is showed.
2. Press “ENTER” button, and there are 11 pre-programmed mode editted in the “EDIT”menu.
CAL WHITE-In this menu, you can adjust the value of 11 different white color.
1. Press “ENTER” button and then UP or DOWN button until “CAL WHITE” is showed.
2. Press “ENTER” button, and there are 11 pre-programmed White colors that can be edited by
adjusting the value of “Red”, “Green”, “Blue” and “White”
STAT COLOR-In this menu, you can adjust the value of static color and strobe speed as you like.
1. Press “ENTER” button and then UP or DOWN button until “STAT COLOR” is showed.
2. Press “ENTER” button, and there are six options. Then press ENTER to select the option and
press UP or DOWN button to select the value you desire as below:
1) STAT RED - You can adjust the red brightness in this menu.
2) STAT GREEN - You can adjust the green brightness in this menu.
3) STAT BLUE - You can adjust the blue brightness in this menu.
4) STAT WHITE - You can adjust the white brightness in this menu.
5) SELET COLOR -You can select 52 static color in this menu.
6) STAT STROB - You can adjust the strobe speed in this menu.
EDIT-In this menu, you can edit your desired AUTO program.
1. Press “ENTER” button and then UP or DOWN button until “EDIT” is showed.
2. Press “ENTER” button, and open the “EDIT” mode to edit the custom programs from“PR.01” to
“PR.11”.And there are 32 scenes that can be edited in each custom program.
3. You can edit a scene by adjusting the value of “RED (0~255)”, “GREEN (0~255)”, “BLUE (0~255)”,
“WHITE (0~255)”, “FADE (0~31)”, “FLASH(0~50)”, “STROBE (0~31)” & “TIME (0~100)” as you like.
Then the data will be saved, when you press the ENTER button for 5 seconds.
UPLOAD-In this menu,you can connect several pieces of lights with MAX cables and set one light as
the MASTER and others in SLAVE mode.Then upload the custom program in the MASTER light to the
lights in SLAVE mode.
1. Press “ENTER” button and then UP or DOWN button until “UPLOAD” is showed.
2. Press “ENTER” button to upload the custom programs from the MASTER light to the
SLAVE ones.
RESET-In this menu, you can reset all the value of the system.
1. Press “ENTER” button and then UP or DOWN button until “RESET” is showed.
2. Press the ENTER button to reset all the value of the system.

Edit Mode
RP-01
RP-11
Custom Mode
01
11
Slave
AUTO MODE
AUTO 01
AUTO 15
01
31
0
255
0-20
1-70
DMX State
Blackout
DMX Hold
Manual Mode
CAL White
2500k
3000k
3500k
4000k
4500k
5000k
6000k
7000k
8000k
9000k
10000k
RED
GREEN
BLUE
WHITE
Strobe
Color
Channels Mode
02
03
04
09
12
Slave Mode
Upload
DMX-In this menu,you can connect several pieces of lights with DMX cable and control them with
control console.
1. Press “ENTER” button and then UP or DOWN button until “DMX ” is showed.
2. Press “ENTER” button, and “CHANNEL” or “ADDRESS” will be showed.Then press ENTER.
1) “Channel [xx]” will be showed, “X” represents the showed DMX channel mode. You can press the
UP or DOWN button to select your desired Channel mode.
2) “xxx” will be showed, “x” represents the showed address. You can press the UP or DOWN button to
select your desired address.
RUN MODE-In this menu, you can select DMX mode or SLAVE mode.In SLAVE mode,you can select
one light as the MASTER light and other lights in SLAVE mode will run following the MASTER light.
1. Press “ENTER” button and then UP or DOWN button until “RUN MODE” is showed.
2.Press “ENTER” button, and“DMX” or “SLAVE” will be showed, then press ENTER to select your
desired mode.
SET UP-In this menu, you can adjust the value of the function.
1. Press “ENTER” button and then UP or DOWN button until “SET UP” is showed.
2. Press “ENTER” button, and there will be nine options. Then,press ENTER to select the option and
press UP or DOWN button to select the value you desire as below.
1) ID number - You can select an ID Number in this menu.Then, you can adjust the value of channel
11 to the corresponding scope and control the light individually with control console.
2) Display Led - In this item,you can select “ON” or “OFF”.If you select ON,the displayer will be on all
the time.And if you select OFF,the displayer will extinguish about ten seconds later.
3) Key locks - You can select whether the password is on or off in this menu , and the password is [
DOWN ] + [ UP ] + [ DOWN ] + [ UP ] .If you select “on”,then you have to input the password before
pressing the buttons.Otherwise,the light won’t respond to your order.
4) Max temp - You can set the your desired Max working temperature about the light in this
menu.When the working temperature of the light exceeds the Max temperature, the color of letter
“Temp xx” showed in the menu will change from white to yellow.Meanwhile, the light will adjust the
working temperature automatically.
5) Dimmer RED - You can adjust the red brightness in this menu.
6) Dimmer GREEN - You can adjust the green brightness in this menu.
7) Dimmer BLUE - You can adjust the blue brightness in this menu.
8) Dimmer WHITE - You can adjust the white brightness in this menu.
9) Dimmer ALL - You can adjust the brightness of each color in this menu.
INFORMATION-In this menu, you can learn about the information of software, hardware and the
working time of the light.
1. Press “ENTER” button and then UP or DOWN button until “INFORMATION” is showed.
2. Press “ENTER” button, and“Software” “Hardware” or “Fix times” will be showed. Then press
ENTER, and you can see three items as below:
1) Software - This item displays the Software information.
2) Hardware - This item displays the Hardware information.
3) Fix times - This item displays the working hours about the light.
Operation