Itec PCE2S User manual

5
Quick Start / PCIe to 2S Adapter 2x Serial (PCE2S) EN
PCIE TO 2S ADAPTER
INTRODUCTION:
PCIe to 2S adapter is card to PCIe slot in PC type PCI express. After instala-
tion of drivers this adapter is as standard 2xCOM ports. This card offers output
RS232 type DB9 Male for asynchronous connection of I/O devices, e.g. external
modem, GSM modem, printer with serial port, barcode reader etc. Baud rate on
serial port enables using in applications in automatization, monitoring and con-
trol of industrial processes.
SPECIFICATION:
• Interface: PCI express specication 1.1
• Ports: 2x Serial RS232 type DB9 (Male)
• UART: Support UART types by 450 to 550 (fully programmable)
• FIFO receiver/transmitter works with data size up 256 byte
• Data rate on Serial port up to 230400bps
• Support Plug&Play and Hot Swap
• Operation system: Win 7/8/10 32+64bit, Linux, DOS
PACKAGE:
• 1x PCIe to 2S adapter
• 1x Panel with cables for 2xDB9 serial
• 2x Low Prole Backplate
• Manual
DRIVER INSTALLATION
(Note: Drivers are available here: www.i-tec.cz/en/)
For Windows®7/8/10 32_64bit
1. Don't insert the PCIe card into PCIe slot.
2. Download corresponding drivers and unpack (unzip) them to HDD from
www.i-tec.cz/en/.
3. Click on the “StnSetup.exe” button for the installation of drivers from a corre-
sponding directory for the OS and “Exit” to nish installation.
4. Shutdown the PC. Place the PCIe card into PCIe slot and then power on the
system.
5. Once the system gets booted the Windows will automatically start installing
the device driver software. If it is necessary, restart the PC.
HARDWARE INSTALLATION
(Warning: at rst read instructions of driver installation)
Note: Connection of the COM connector- a red core in the cable from DB-9
belongs to the sign ∆ on the PCE card

6
Quick Start / PCIe to 2S Adapter 2x Serial (PCE2S)EN
1. Turn off the computer and disconnect it from the power supply of 230V.
2. Unplug the power cord and remove your computer's cover. Remove the slot
bracket from an available PCIe slot.
3. To install the card, carefully align the card's bus connector with the selected
PCIe slot on the motherboard. Push the board down rmly. Replace the slot
bracket's holding screw to secure the card.
4. Replace the computer cover and reconnect the power cord.
To Verify Windows®Driver Installation
Go to the Device Manager (for example, in Win10: the right mouse button
on Start- Device Manager).
You can see new devices under (COM & LPT).
2x PCIe to High Speed Serial Port (COMx)
Note:
• On „PCIe to High Speed Serial Port (COMx)“, set Communication Properties
as follows (by the mouse right button-Properties):
• on list Properties -Port Settings set proper Bit per second and other param-
eters; you can change number of COM port also
• next click on list Properties -Advanced – choose type of port RS232 . Click
on „DMA settings“ button and choose required settings of DMA access -
OK; next click on „Adv Baudrates..“ button and choose either „Use default
baud rate“ or „Use custom baud rate“ for settings by your requirements. All
settings conrm OK or with help Defaults you return to default settings.
Installation for other OS: Drivers are available here: www.i-tec.cz/en/.
Follow the advices in several driver folders (DOS, Linux) for PCIe (PCE2S).
SAFETY INSTRUCTIONS
• Do not expose to extreme temperatures and air humidity.
• Use the device on at surfaces – you will prevent it from slipping and falling
to the ground.
• Save the user manual for a possible use later.
In cooperation with the service department:
• Check functionality after falling to water or to the ground.
• Check functionality when the cover is broken.
• Send the device back if it does not work in accordance with the user
manual.
FREQUENTLY ASKED QUESTIONS
Available on our website www.i-tec.cz/en on the “FAQ” tab of this product.