iver IV011 Configuration guide

*Image used for illustration purposes only.
Install
Instructions
Pull Handle
(Timber Door)
Australia
14 - 16 Stepney Street,
Stepney, South Australia 5069
P: [phone]
[e-mail]
iver.com.au
SDG Trading Pty Ltd
trading as Iver
ACN 008 154 041 | ABN 18 008 154 041
Contact Us
Southern Design Group
New Zealand
P: [phone]
[e-mail]
iver.co.nz
Scan for
Product &
Finish Care
Information
Scan for NZ
Warranty
Scan for AU
Warranty

1.1. This is the distance from the middle of the top
xing point to the middle of the bottom xing
point. If unsure, this measurement can be found
in the product description on the box and in the
specications on our website. (Figure 1)
1. Determine the Centre to Centre
(CTC) measurement of your
pull handle
2.1. Mark the top xing point on the face of your door
at the desired height and horizontal distance from
door edge.
2.2. In most instances, the horizontal position should
align with the centre of the door stile on a panel
door or with any lock, turn or escutcheon tted to
the door. (Figure 2)
2.3. Using a spirit level, mark the bottom xing point
— noting the CTC measurement. (Figure 3)
2. Marking the Door
Preferred product height
Figure 3.
Figure 2.
Figure 4.
Figure 5.
Figure 1.
3.1. Remove the taylor spindles from the pull handle by
loosening the grub screws. (Figure 4)
3. Fitting the Pull Handle
(Concealed Fix Method)
3.2. Centre one of the taylor spindles on the top xing
hole and using a pencil, mark the three wood screw
holes. Repeat for the bottom xing point.
3.3. Drill 2mm pilot holes for the wood screws at each of
the six marks and ax the taylor spindles to the door
with wood screws provided. (Figure 3)
3.4. Place pull handle on taylor spindles and tighten both
grub screws to secure.
(1)
(2)
(4)
(2)
(5)
IMPORTANT:
Please install this door hardware in the following
order to ensure its warranty is not voided.
1. Install the door hardware on raw / unnished door
using the instructions provided.
2. Remove door hardware and store safely. Do not place
painters tape or masking tape over the product. The
tape will damage the nish.
3. Paint / nish door.
4. Reinstall hardware.
Please recycle me after use

5.1. Drill holes through door at the xing points marked
in step 2.1.
5.2. It is important to drill halfway through the door
from one door face and complete the hole from
the other side to prevent splintering.
5.3. Remove taylor spindles on both pull handles by
loosening grub screws.
5.4. Screw a taylor spindle onto one side of each
threaded bolt.
5.5. Insert bolt through hole and screw taylor spindle
onto opposite end of thread. Hand tighten
and ensure taylor spindles are ush against the
door faces. (Figure 7)
5.6. If required cut threaded bolt to allow taylor spindles
to sit ush with door.
5.7. To prevent loosening, x taylor spindles on each side
with 2 x woodscrews.
Repeat 5.4 – 5.6 at bottom xing point.
5.8. Place pull handles on taylor spindles and tighten all
grub screws to secure.
5. Fitting the Pull Handle (Axing a Pair)
(3) (2)
(5)
(1)
Not Included:
Included:
Figure 7.
4.1. Drill holes through door at the xing points marked
in step 2.1.
4.2. It is important to drill halfway through the door
from one door face and complete the hole from the
other side to prevent splintering.
4.3. Insert xing bolts through the holes from the inside
of the door.
4.4. With taylor spindles already attached to the pull
handle, align the female thread of the taylor spindle
to the top xing bolt and tighten. Repeat for
bottom xing point. (Figure 6)
4. Fitting the Pull Handle
(Rear Fix Method)
Figure 6.
(3)
(1)
1. Pull Handle
2. Taylor
Spindles
3. Fixing Bolts
4. Wood Screws
5. Grub Screws
6. Hex Key
PLEASE NOTE:
The screws provided with Iver products are made from solid brass.
This allows nishes to be matched as closely as possible and
prevents the possibility of screws rusting in coastal areas. Please
note that screws require pre-drilling.
Please take extra care when tting.