jablotron JA-83M User manual

Fig. 1 Fig. 2
Fig. 3 Fig. 4
1. Mounting holes of the detector
2. Mounting holes of the magnet A
3. Magnet A and B position marks
4. Serial number
5. Reed contact
6. Battery CR123A
7. Tamper
8. Settings jumper
A
B
JA-83M - Wireless Magnetic Door/Window Detector
The JA-83M is designed to detect opening windows,
doors etc. It can be installed onto most plastic or
wooden frames.
The JA-83M detector is suitable for indoor installations only.
Installation should only be undertaken by technicians holding
a certicate issued by an authorised distributor. The detector
must not be exposed to bending or other deformation, as it
may become damaged.
Choose the suitable place for detector’s installation. The
detector reacts to the removal of its magnet unit. The
electronics should be installed onto the non-moving part
of windows or doors, and the magnet onto the moving
part. Avoid locating it directly on a metal frame as metal
inuences the functioning of the magnetic sensor and radio
communication.
Installation - Overview
1. Open the detector cover by pressing the tab in (Fig. 1).
2. Screw the rear cover to the solid part of the door/window.
The marks A and B show the right position of the magnet.
(Fig. 3)
3. Attach the magnet to the moving part of the window. The
standard magnet in a plastic housing opposite the A arrow
and the small round magnet against the B arrow. Its distance
from the detector should be as small as possible when the
door/window is closed. In the picture Fig. A and Fig. 6 are
shown the reaction areas for magnets in millimeters in three
axes of movement and on the non-magnetic / magnetic
surface. Note: Use the supplied plastic spacer to compensate
for possible height difference for magnet A.
4. Pair the detector to an actuator/receiver. Check the
actuator’s manual for more information. The RF wireless
signal is only transmited when the battery is inserted.
Note: To pair a detector after having already connected a
battery, rst disconnect the battery, then press and release
the tamper sensor to discharge any remaining charge to get
the device ready for pairing.
5. Mount the front cover onto the rear part.
6. Test the detector’s function.
7. The tab can be xed using supplied screw (Fig. 2).
8. Programming of the detector to switching receiver see
overleaf.
Installation
The Components
Fig. 5
Fig. 6
For use with the range of switching receivers.
e.g. RFSA-61B, RFSAI-61B, RFSA-62B, RFSA-61M & RFSA-66M
www.click-smart.com

Pairing The Detector:
Step 2 - Assign The Device
The device will now switch on / off without any delay.
To programme an off delay proceed to the next step, to
exit programming proceed to step 4.
Press & hold the ‘programming’ button on the receiver for 2 seconds
(the status LED will ash with a 1 second interval).
Programming button Status LED
Will ash once per
second
Press and hold 2
seconds
Step 1 - Activate The Receiver
To exit programming mode press the
programme button for 1 second only.
Replace the battery cover.
Press and hold for 1
second
Step 4 - Save And Exit
B. Press and hold programme button for
8 seconds - this will delete ALL stored functions
Release programming button and then press for <1 second to exit
Select A or B To Delete Stored Function
Insert the battery, replace the cover, after ten
seconds close and open the door / window, the
receiver LED will ash at an increased speed
once to conrm detector assignment.
Step 3 - To Prepare For Function 5
Remove battery - wait 30 seconds
Re-insert battery to set time delay mode
Remove for another 30 seconds
Press button on receiver for < 5 seconds to start counter
When required time elapsed re-insert battery
Switching Actuator Function 5 - ‘OFF DELAY’
Remove cover to reveal battery compartment
A. Press and hold programme button for
5 seconds the LED will ash twice a second.
Remove and re-install batteries - this will delete
the single pairing.
Always replace both battery cells at the same time.
We recommend using a high quality brand name battery (e.g. Panasonic).
After the batteries have been replaced, detector function should be tested.
Expired batteries should be disposed of according to local regulations.
Battery Type: CR123A Lithium
Voltage: 3.0V DC
Typical battery life: Approx. 3 years (for 20 daily activations)
Communication band: 868 MHz
Communication range: Approx. 300m (open area)
Operational environment according to EN 50131-1 II.indoor general
Operational temperature range: -10 to +40 °C
Dimensions: Transmitter: 75 x 31 x 23 mm
Magnet A: 56 x 16 x 15mm
Magnet B: 10mm diameter x 24mm
EN 50131-1, CLC/TS 50131-2-2, EN 50131-5-3 classication: Grade 2
Complies with: ETSI EN 300220, EN 50130-4, EN 55022, EN 60950-1
Can be operated according to: ERC REC 70-03
Battery Replacement
Technical Specications
Scolmore Park, Landsberg, Licheld Road Industrial Estate, Tamworth, Staffordshire B79 7XB
Tel: [phone] Fax: [phone] www.scolmore.com V1.0