JABSCO 18690-0000 User manual

Model 18690-0000
above the maximum liquid level should service be needed when
the tank is full.
Plumbing Connections: Use 1-1/2" ID non-collapsible suction
hose. Attach suction hose to the inlet port and secure it with a
quality marine grade hose clamp. All suction connections must be
airtight and free of sharp bends or restrictions. Use minimum 1"
ID contractors hose for discharge.
Be sure adequate voltage and current capacity is available in
electrical installation.
OPERATING INSTRUCTIONS
The Jabsco macerator pump unit has been designed to handle
waste, toilet tissue, and facial tissue. It will also handle solids
such as filter tip cigarettes, cigars and chunks of soft fruits or
vegetables less than 1" in size. It will NOT pump solid objects
like peach pits, rags, or sanitary napkins. The holding tank and
pump should be flushed with several gallons of water after each
pumpout. Do NOT run pump dry for longer than 30 seconds.
SERVICE INSTRUCTIONS
1.Remove acorn nuts and inlet housing.
2.Unscrew nut retaining cutter plate from shaft by turning
counterclockwise facing cutter. Hold motor shaft behind
chopper to prevent shaft from turning with a thin 9/32"
(7 mm) ignition wrench.
3.Remove gaskets, wearplate and slide pump assembly off
of mounting studs.
4.Replace seal, impeller gaskets or other parts as necessary.
To remove seal, push out evenly with screwdriver from
impeller bore side of body. To reassembly seal, coat out-
side of metal case with a light coat of sealant and press
into body with lip facing impeller. Press star retaining wash-
er (with concave side up) into seal bore and against seal
case. A light coating of grease should then be applied to
impeller bore and wearplate to aid initial dry startup.
5.Reassemble body, impeller, gaskets, wearplate, cutter
plate, suction housing and acorn nuts.
115 VOLT AC MACERATOR
FEATURES
Pump: Self-Priming Flexible Impeller
with Stainless Steel Wearplates
Impeller: Jabsco Nitrile Compound
Macerator: Stainless Steel Cutter Plate reduces
particle size to 1/8" (3.17 mm) maximum
Seal: Lip Type
Ports: Inlet – 1-1/2" (38 mm) NPT Male
and 1-1/2” (38 mm) barb
Outlet – 1" (25.4 mm) Hose Barb
Motor: 115 Vac, AC Induction Type
Single Phase, 60 Hz
Thermal Overload Protection
Weight: 19 lb (41.8 kg)
APPLICATION INFORMATION
The Jabsco 18690-0000 AC macerator pump unit is the ideal
answer to waste handling problems for marine, recreational
vehicle and domestic uses. The macerator section grinds
waste down to a particle size of 1/8" maximum so it can be
pumped easily through a 1" hose discharge line. The pump is
self-priming, permitting the unit to be mounted above or below
the tank in a convenient location. For optimal efficiency, locate
pump as close to waste source as practical.
Empties a 30 gallon holding tank in only 3 minutes.
The 18690-0000 waste pump will macerate and pump all waste
and tissue normally found in marine waste systems. IT WILL NOT
HANDLE HARD SOLID OBJECTS, SANITARY NAPKINS OR RAGS.
HEAD CAPACITY TABLE
Feet of Head GPM
514.0
10 13.0
20 10.0
30 7.5
Flow rates are for water, capacity may be slightly reduced when
handling heavy solids. Full load Amps – 7.2
INSTALLATION
Locating the pump: The Jabsco AC macerator pump unit is
self-priming to a six foot lift and may be located at any convenient
point in the waste discharge system. It should be mounted
upright so the motor’s bearing lube channels are accessible and
to prevent the oil from draining out of them. For optimal efficiency,
locate pump as close to waste source as practical. Ideally, if con-
nected to the bottom of the holding tank, the hose length should
be long enough so the hose-to-pump connection can be raised
WARNING
!
Explosion hazard. motor can spark.
Explosion & death can occur.
Do not use where flammable vapors
are present.
Model 18690-000

U.S.A.
Jabsco
20 Icon
Foothill Ranch, CA 92610-3000
Tel: [phone]
Fax: [phone]
UNITED KINGDOM
Jabsco
Bingley Road, Hoddesdon
Hertfordshire EN11 OBU
Tel: [phone]
Fax: [phone]
CANADA
Fluid Products Canada
55 Royal Road
Guelph, Ontario N1H 1T1
Tel: [phone]
Fax: [phone]
JAPAN
NHK Jabsco Company Ltd.
3-21-10, Shin-Yokohama
Kohoku-Ku, Yokohama, 222
Tel: [phone]
Fax: [phone]
GERMANY
Jabsco GmbH
Oststrasse 28
22840 Norderstedt
Tel: [phone]
Fax: [phone]
THE PRODUCTS DESCRIBED HEREIN ARE
SUBJECT TO THE JABSCO ONE YEAR LIMITED
WARRANTY, WHICH IS AVAILABLE FOR YOUR
INSPECTION UPON REQUEST.
©Copyright 2003, ITT Industries Printed in U.S.A. All Rights Reserved Form: 43000-0186 Rev. 11/2003
5-3/4
(146)
3/4 (19) HANDLE
7-15/16
(202)
4-3/16
(106)
3/8
(10)
2-1/8
(54)
2-7/8
(73)
4-1/4
(108)
4-1/8
(105)
2-3/4
(70) 2-5/8
(67) 5-1/8
(130)
14-13/16
(376)
3-5/8
(92)
7/16
(11)
3-11/16
(94) REF.
5-11/16
(144)
DIA
1-1/2 N.P.T.
6 FT ±3" LONG ELECTRICAL
CORD WITH 3 PRONG PLUG 7-1/4
(184 )
3/16
(5)
3
(76)
3/4 (19)
BARBED FOR
1" ID HOSE
BARBED FOR
1-1/2" ID HOSE
12-1/8
(308)
C OF PORT
13 14
11 12
1234
5
678910
7
PARTS LIST Part Qty.
Key Description Number Req.
1Acorn Nut 91085-0340 4
2Fiber Washer 91613-0140* 4
3Stud, Short 17288-0010* 2
4Macerator Housing 18594-1001 1
5Cutter Plate with Nut 37056-1000 1
6Wearplate, Large 18597-1000 1
7Gasket Kit (2 ea per kit) 18596-1000* 1
Part Qty.
Key Description Number Req.
8Impeller 6303-0003* 1
9Wearplate, Small 12316-1002 1
10 Body 18593-1000* 1
11 Seal 1040-0000* 1
12 Slinger 6342-0000 1
13 Stud, Long 17288-0000 2
14 Motor Sub-Assembly-115v 18744-0000 1
Service Kit 18598-1000
*These parts are supplied in 18598-1000 service kit.
DIMENSIONAL DRAWING
Inches (Millimetres)
EXPLODED VIEW