Jandy WPLV100WS30 User manual

Underwater Pool and Spa
White Lights
H0312200_REVD
WARNING
FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and
qualified in pool equipment by the jurisdiction in which the product will be installed where such state or
local requirements exist. The maintainer must be a professional with sufficient experience in pool equipment
installation and maintenance so that all of the instructions in this manual can be followed exactly. Before
installing this product, read and follow all warning notices and instructions that accompany this product.
Failure to follow warning notices and instructions may result in property damage, personal injury, or death.
Improper installation and/or operation may void the warranty.
Improper installation and/or operation can create unwanted electrical hazard which can
cause serious injury, property damage, or death. DO NOT MODIFY THIS EQUIPMENT
ATTENTION INSTALLER - This manual contains important information about the installation,
operation and safe use of this product. This information should be given to the owner/
operator of this equipment.
INSTALLATION AND
OPERATION MANUAL
ENGLISH | FRANÇAIS | ESPAÑOL

Page 2 ENGLISH Jandy®Underwater Pool and Spa White Lights | Installation & Operation Manual
Section 1. Important Safety Information................3
Section 2. Product Description and Model
Numbers .................................................4
Section 3. Installing Jandy Light Fixture
During New Construction......................5
3.1 Preparing the Light Fixture for Installation..........5
3.2 Installing the Light Fixture ..................................6
Section 4. Replacing Jandy Light Fixture
in an Existing Pool or Spa.....................7
4.1 Preparing the Light Fixture for Replacement......7
4.2 Replacing the Light Fixture ................................7
Section 5. Wiring Options for Controlling
Jandy Pool or Spa White Lights.........10
5.1 Wiring to an AquaLink®RS Control System......10
5.2 Wiring to a Time Clock......................................10
5.3 Wiring to a Switch.............................................10
Section 6. Operating Instructions ........................10
6.1 To Operate the Light .........................................10
Section 7. Replacing the Lamp.............................10
Section 8. Twelve (12) Volt Installation ................13
Section 9. Exploded View and
Replacement Parts...............................14
9.1 Jandy Pool White Light.....................................14
9.2 Jandy Spa White Light......................................15
Table of Contents

Page 3
ENGLISH
Jandy®Underwater Pool and Spa White Lights |Installation & Operation Manual
Section 1. Important Safety Information
IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO A RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY TO PERSONS
READ AND FOLLOW ALL INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be followed, including the
following:
WARNING
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION. This underwater light must be installed by a licensed
or certied electrician in accordance with the National Electrical Code® (NEC®) in the US, the Canadian
Electrical Code (CEC) in Canada, and applicable local codes and ordinances. Improper installation will create
an electrical hazard, which could result in death or serious injury to pool or spa users, installers, or others due to
electrical shock, and may also cause damage to property. Read and follow the specic instructions below.
WARNING
Before installing this underwater light, read and follow all warning notices and instructions accompanying this
light. Failure to follow safety warnings and instructions can result in severe injury, death, or property damage.
Call [phone] or visit Jandy.com for additional free copies of these instructions.
CAUTION
Except when the Jandy pool and spa lights are installed in an area of the swimming pool that is not used for
swimming and the lens is adequately guarded to keep any person from contacting it, the light shall be installed
in or on a wall of the pool, with the top of the lens opening not less than 18 inches (457 mm) below the normal
water level of the pool
ATTENTION INSTALLER: This manual contains important information about the installation,
operation and safe use of this product. This information should be given to the owner/operator
of this equipment.
SAVE THESE INSTRUCTIONS

Page 4 ENGLISH Jandy®Underwater Pool and Spa White Lights | Installation & Operation Manual
Section 2. Product Description and Model Numbers
Jandy
Model Number
Jandy
White Light Size Voltage Maximum Watts
Cord
Length Face Ring Material
WPLV100WS30 Pool 12 Volt AC 100 30 feet Stainless Steel
WPLV100WS50 Pool 12 Volt AC 100 50 feet Stainless Steel
WPLV100WS100 Pool 12 Volt AC 100 100 feet Stainless Steel
WPLV100WS50C Pool (Canadian) 12 Volt AC 100 50 feet Stainless Steel
WPLV100WS100C Pool (Canadian) 12 Volt AC 100 100 feet Stainless Steel
WPLV300WS30 Pool 12 Volt AC 300 30 feet Stainless Steel
WPLV300WS50 Pool 12 Volt AC 300 50 feet Stainless Steel
WPLV300WS100 Pool 12 Volt AC 300 100 feet Stainless Steel
WPLV300WS50C Pool (Canadian) 12 Volt AC 300 50 feet Stainless Steel
WPLV300WS100C Pool (Canadian) 12 Volt AC 300 100 feet Stainless Steel
WPHV300WS30 Pool 120 Volt AC 300 30 feet Stainless Steel
WPHV300WS50 Pool 120 Volt AC 300 50 feet Stainless Steel
WPHV300WS100 Pool 120 Volt AC 300 100 feet Stainless Steel
WPHV300WS150 Pool 120 Volt AC 300 150 feet Stainless Steel
WPHV300WS250 Pool 120 Volt AC 300 250 feet Stainless Steel
WPHV300WS50C Pool (Canadian) 120 Volt AC 300 50 feet Stainless Steel
WPHV300WS100C Pool (Canadian) 120 Volt AC 300 100 feet Stainless Steel
WPHV500WS30 Pool 120 Volt AC 500 30 feet Stainless Steel
WPHV500WS50 Pool 120 Volt AC 500 50 feet Stainless Steel
WPHV500WS100 Pool 120 Volt AC 500 100 feet Stainless Steel
WPHV500WS150 Pool 120 Volt AC 500 150 feet Stainless Steel
WPHV500WS250 Pool 120 Volt AC 500 250 feet Stainless Steel
WPHV500WS50C Pool (Canadian) 120 Volt AC 500 50 feet Stainless Steel
WPHV500WS100C Pool (Canadian) 120 Volt AC 500 100 feet Stainless Steel
WPLV100WP100 Pool 12 Volt AC 100 100 feet Plastic
WPLV300WP100 Pool 12 Volt AC 300 100 feet Plastic
WPHV300WP100 Pool 120 Volt AC 300 100 feet Plastic
WPHV500WP100 Pool 120 Volt AC 500 100 feet Plastic
WSLV100WS30 Spa 12 Volt AC 100 30 feet Stainless Steel
WSLV100WS50 Spa 12 Volt AC 100 50 feet Stainless Steel
WSLV100WS100 Spa 12 Volt AC 100 100 feet Stainless Steel
WSLV100WS50C Spa (Canadian) 12 Volt AC 100 50 feet Stainless Steel
WSLV100WS100C Spa (Canadian) 12 Volt AC 100 100 feet Stainless Steel
WSHV100WS30 Spa 120 Volt AC 60 30 feet Stainless Steel
WSHV100WS50 Spa 120 Volt AC 60 50 feet Stainless Steel
WSHV100WS100 Spa 120 Volt AC 60 100 feet Stainless Steel
WSHV100WS150 Spa 120 Volt AC 60 150 feet Stainless Steel
WSHV100WS250 Spa 120 Volt AC 60 250 feet Stainless Steel
WSHV100WS50C Spa (Canadian) 120 Volt AC 60 50 feet Stainless Steel
WSHV100WS100C Spa (Canadian) 120 Volt AC 60 100 feet Stainless Steel
WSLV100WP100 Spa 12 Volt AC 100 100 feet Plastic
WSHV100WP100 Spa 120 Volt AC 60 100 feet Plastic

Page 5
ENGLISH
Jandy®Underwater Pool and Spa White Lights |Installation & Operation Manual
Some of the requirements of the National Electrical
Code, which the pool or spa’s electrical systems must
meet, are as follows:
• The Junction Box (or, for 12 volt models, the low
voltage transformer) must be located at least eight
(8) inches above water level, at least four (4) inches
above ground level or pool deck level, and at least
four (4) feet from the edge of the pool or spa; see
Figure 1 for pools and Figure 2 for spas.
• The light xture and all metal items within ve (5)
feet of the pool or spa must be properly electrically
bonded to a reliable point of grounding.
• The wet niche must be properly installed so that the
top edge of the underwater light’s lens is at least 18
inches below the surface of the water in the pool or
spa; see Figure 1 or 2.
• The wet niche must be properly electrically bonded
and grounded via the No. 8 AWG ground connector
located at the rear of the niche; see Figure 1 or 2.
National Electrical Code®(NEC®) requires
bonding of the Pool Water. Where none of the
bonded pool equipment, structures, or parts are
in direct connection with the pool water; the pool
water shall be in direct contact with an approved
corrosion-resistant conductive surface that exposes
not less than 5800 mm² (9 in²) of the surface area
to the pool water at all times. The conductive
surface shall be located where it is not exposed
to physical damage or dislodgement during usual
pool activities, and it shall be bonded in accordance
with the bonding requirements of NEC Article 680.
Refer to locally enforced codes for any additional
pool and spa bonding requirements.
NOTE: The pool or spa electrical system can be
verified with a Pool and Spa Electrical
Qualification Test kit. The test kit is available
from local distribution. The electrical system
inspection using this kit must be performed by
trained and certified personnel. To be certain
that the pool or spa’s electrical system meets all
applicable requirements, the electrician should
also consult the local building department.
Use only approved wet niches (see following note) to
ensure a safe and proper installation.
Section 3. Installing Jandy Light
Fixture During New
Construction
WARNING
Risk of Electrical Shock or Electrocution
This underwater light must be installed by a
licensed or certied electrician or a qualied pool
or spa serviceman in accordance with the National
Electrical Code® (NEC®) in the US, the Canadian
Electrical Code in Canada, and all applicable local
codes and ordinances. Improper installation will
create an electrical hazard, which could result
in death or serious injury to pool or spa users,
installers or others due to electrical shock, and
may also cause damage to property.
Always disconnect the power to the pool or spa
light at the circuit breaker before servicing the
light. Failure to do so could result in death or
serious injury to serviceman, pool or spa users or
others due to electrical shock.
3.1 Preparing the Light Fixture for
Installation
NOTE: The electrician must complete preparatory steps
before light fixture is installed; see Figure 1 (or
Figure 2, for spa).
Ensure that the pool or spa meets the requirements of
the current National Electrical Code (NEC) in the US,
the Canadian Electrical Code (CEC) in Canada, and all
applicable local codes and ordinances. A licensed or
certied electrician must install the electrical system
to meet or exceed those requirements before the
underwater light is installed.
WARNING
Risk of Electrical Shock or Electrocution
which could result in serious injury or death. A
Ground Fault Circuit Interrupter (GFCI) for 120
Volt transformers should be used if required by
the transformer manufacturer or if required by
the local applicable code and/or Authority Having
Jurisdiction (AHJ). When a GFCI is used, the
conductors on the load side of the GFCI circuit
shall not occupy conduit boxes, or enclosures
containing other conductors unless the additional
conductors are also protected by a GFCI. Refer to
local codes for complete details.

Page 6 ENGLISH Jandy®Underwater Pool and Spa White Lights | Installation & Operation Manual
Figure 1. Jandy Pool White Light Installation
4" min.
48"
min.
8" min. Junction Box or Low
Voltage Transformer, to the
max water level of the pool.
18" min. to top of Lens.
11.50"
Concrete must be cut
back around Niche to
allow for a compacted
plaster seal.
Coil 4 ft. of light cable
around Fixture.
Rigid
Conduit
To GFCI, Circuit
Breaker and
Power Source.
16”
#8 AWG Ground
Connector bonded
Figure 2. Jandy Spa White Light Installation
4" min.
48"
min.
8" min. Junction Box or
Low Voltage Transformer.
18" min. to top of Lens.
6.0"
Concrete must be cut
back around Niche to
allow for a compacted
plaster seal.
Coil 4 ft. of light cable
around Fixture.
#8 AWG Ground
Connector bonded
to rebar.
Rigid
Conduit
To GFCI, Circuit
Breaker and
Power Source.
NOTE: Jandy Pool and Spa Lights are ETL
listed (ETL report/file 3101015CHI-002)
for installation with only the following
manufacturer’s wet niche fixtures:
Large / Pool Type Niche Model Numbers:
Jandy: PLNICLRG, PLNICVFLRG, SSNICLRG1(R/S)
Pentair®: 620004, 78210200 thru 700, 78210401
Hayward® DuraNiche: SP0600U
Small / Spa Type Niche Model Numbers:
Jandy: PLCNICSM, SSNICSM1(R/S)
Pentair: 79206600
3.2 Installing the Light Fixture
NOTE: Perform these steps only after the electrical
system requirements are met.
1. Feed cord through conduit to Junction Box,
leaving at least four (4) feet of cord at the light
xture to coil around the light; see Figure 1 (or
Figure 2, for spa). This four (4) feet of cord around
the light allows the light to be serviced after the
pool or spa is lled with water.
2. Cut the cord at the Junction Box, leaving at least
six (6) inches of cord to make connections.
3. Strip six (6) inches of the outer cord jacket to
expose the three insulated wires. Be careful not to
damage the insulation on the three (3) inner wires.
4. Install strain relief over cord jacket and connect all
three (3) wires to the corresponding circuit wires in
the Junction Box. Install the Junction Box cover.
WARNING
Never operate this underwater light for more than
10 seconds unless it is totally submerged in water.
Without total submersion, the light assembly will
get extremely hot, which may result in serious
burns or in breakage of the lamp or lens. This
may result in serious injury to pool or spa users,
installers, or bystanders or damage to property.
5. Coil the 4-foot length of cord around the xture
and place the light assembly into the niche.
6. Engage the retainer tab on the bottom of the face
ring, then pivot the top of the xture inward and
tighten the special pilot screw.
WARNING
Use only the special pilot screw provided with this
underwater light. This screw mounts and electrically
grounds the mounting ring to the wet niche. Failure
to use the screw provided could create an electrical
hazard, which could result in death or serious injury
to pool or spa users, installers or others due to
electrical shock.
7. Fill the pool or spa until the underwater light is
completely submerged in water before operating
the light for more than 10 seconds. Turn on
main switch or circuit breaker, and the switch,
which operates the underwater light, to check for
proper operation. Refer to Section 6, Operating
Instructions.

Page 7
ENGLISH
Jandy®Underwater Pool and Spa White Lights |Installation & Operation Manual
3. The light xture and all metal items within ve (5)
feet of the pool or spa must be properly electrically
bonded to a reliable point of grounding.
4. The wet niche must be properly installed so that
the top edge of the underwater light’s lens is at
least 18 inches below the surface of the water in
the pool or spa; see Figure 1 (or Figure 2, for spa).
5. The wet niche must be properly electrically
bonded and grounded via the No. 8 AWG ground
connector located at the rear of the niche; see
Figure 1 (or Figure 2, for spa).
To be certain that the pool or spa’s electrical system
meets all applicable requirements, the electrician should
also consult the local building department.
4.2 Replacing the Light Fixture
NOTE: Perform these steps only after the electrical
system requirements are met.
WARNING
Failure to bring the pool or spa’s electrical system
up to code requirements before installing the
underwater light will create an electrical hazard
which could result in death or serious injury to pool
or spa users, installers, or others due to electrical
shock, and may also cause damage to property.
NOTE: The light fixture may be replaced without
removing water from the pool or spa.
1. Turn o the main electrical switch or circuit
breaker, as well as the switch, which operates the
underwater light.
2. Unscrew the special pilot screw at the top of the
face ring and remove the light assembly from the
niche, and place the assembly on the deck.
WARNING
Be sure to keep the special pilot screw from this
underwater light. This screw mounts and electrically
grounds the housing securely to the mounting ring
and wet niche. Failure to use the screw provided
could create an electrical hazard, which could
result in death or serious injury to pool or spa
users, installers or others due to electrical shock.
Section 4. Replacing Jandy Light
Fixture in an Existing Pool
or Spa
WARNING
Risk of Electrical Shock or Electrocution.
This underwater light must be installed by a
licensed or certied electrician or a qualied pool
or spa serviceman in accordance with the National
Electrical Code in the US, the Canadian Electrical
Code in Canada, and all applicable local codes
and ordinances. Improper installation will create
an electrical hazard, which could result in death
or serious injury to pool or spa users, installers or
others due to electrical shock, and may also cause
damage to property.
Always disconnect the power to the pool or spa
light at the circuit breaker before servicing the light.
Failure to do so could result in death or serious
injury to serviceman, pool or spa users or others
due to electrical shock.
4.1 Preparing the Light Fixture for
Replacement
Verify that the pool or spa meets the requirements of
the current National Electrical Code® (NEC®) in the
US, the Electrical Code in Canada, and all applicable
local codes and ordinances. A licensed or certied
electrician must install the electrical system to meet or
exceed those requirements before the underwater light
is installed. Some of the requirements of the National
Electrical Code, which the pool or spa’s electrical
system must meet, are as follows:
1. The lighting circuit must have a Ground Fault
Circuit Interrupter (GFCI) for line voltage 120
volt models, and must have an appropriately rated
circuit breaker.
2. The Junction Box (or, for 12 volt models, the
low voltage transformer) must be located at least
eight (8) inches above water level, at least four (4)
inches above ground level or pool deck level, and
at least 48 inches from the edge of the pool or spa;
see Figure 1 (or Figure 2, for spa).

Page 8 ENGLISH Jandy®Underwater Pool and Spa White Lights | Installation & Operation Manual
3. Remove the Junction Box cover, disconnect the
light xture wires and strain relief, and then pull
the cord out of the conduit from the niche.
4. Feed the new light xture cord through the conduit
from the niche to the Junction Box.
NOTE: Depending on the length of the conduit, special
tools may be required to pull the cord through
the conduit.
5. Leave at least four (4) feet of cord to coil around
the light xture; see Figure 1 (or Figure 2, for spa).
This allows the light to be serviced after the pool
or spa is lled with water.
6. Cut the cord at the Junction Box, leaving at least
six (6) inches of cord to make connections.
7. Strip six (6) inches of the outer cord jacket from
the cord to expose the three insulated wires. Be
careful not to damage the insulation on the three
(3) inner wires.
8. Install the strain relief over the cord jacket and
connect all (3) three wires to the corresponding
circuit wires in the Junction Box. Install the
Junction Box cover.
9. Reinstall the light assembly into the niche and
tighten the special pilot screw.
WARNING
Use only the special pilot screw provided with this
underwater light. This screw mounts and electrically
grounds the mounting ring to wet niche. Failure to
use the screw provided could create an electrical
hazard, which could result in death or serious injury
to pool or spa users, installers or others due to
electrical shock.
10. Fill the pool or spa until the underwater light is
completely submerged in water before operating
the light for more than 10 seconds. Turn on main
switch or circuit breaker, as well as the switch,
which operates the underwater light, to check for
proper operation. Refer to Section 6, Operating
Instructions.
WARNING
Never operate this underwater light for more than
10 seconds unless it is totally submerged in water.
Without total submersion, the light assembly will
get extremely hot, which may result in serious
burns or in breakage of the lamp or lens. This
may result in serious injury to pool or spa users,
installers, or bystanders or in damage to property.

Page 9
ENGLISH
Jandy®Underwater Pool and Spa White Lights |Installation & Operation Manual
Figure 5. Wiring the Jandy Pool and Spa White
Light to a Time Clock
Clock
Motor
Ground
Ground
Neutral
Line
A12
GFCI
Black
White
Green
Black White Green
JUNCTION
BOX
120V
Jandy
Light
120 V
SUPPLY
Figure 6. Wiring the Jandy Pool and Spa White
Light to a Switch
Ground
Ground
Neutral
Line
120 V
Supply
GFCI
Black
White
Green
JUNCTION
BOX
Black
White
SWITCH
Clock
Motor
Ground
Ground
Neutral
Line
A12
GFCI
Black
White
Green
Black White Green
JUNCTION
BOX
120V
Jandy
Light
120 V
SUPPLY
Figure 3. 120-Volt Jandy Pool and Spa White Light
Wiring Diagram
GFCI
Black
White
Green
Ground
Ground
Neutral
120 VAC
Power Supply
Black
White
Green
JUNCTION
BOX
120V
Jandy
Light
Figure 4. 12-Volt Jandy Pool and Spa White Light
Wiring Diagram
GFCI
Black
White
Green
Ground
Ground
Neutral
120 VAC
Power Supply
Black
White
Green
JUNCTION
BOX
120V
Jandy
Light
120V/12V
Transformer
Black
White
Green
Black
White
Green
Ground
Neutral
120 VAC
Power Supply
Black
White
Green
JUNCTION
BOX
12V
Jandy
Light
120V/12V
Transformer
Black
White
Green

Page 10 ENGLISH Jandy®Underwater Pool and Spa White Lights | Installation & Operation Manual
NOTE: The Jandy Pool and Spa White Lights are
available in 120-volt and 12-volt versions. If
installing a 12-volt light, a 120-volt/12-volt step-
down (AC) transformer must be used. For more
information about 12-volt installations, refer to
Section 8 of this manual.
5.2 Wiring to a Time Clock
The Jandy Pool and Spa White Lights can be wired
into a basic time clock to automatically turn on the
lights at a predesignated time. Refer to Figure 5 to
connect the lights into the time clock.
5.3 Wiring to a Switch
The Jandy Pool and Spa White Lights can be wired
into a switch to manually turn on/o the lights. Refer to
Figure 6 to connect the lights into the switch.
Section 6. Operating Instructions
6.1 To Operate the Light
Activate the light by either turning on the switch, setting
a program, or by pushing the button on a pool and spa
controller.
Section 7. Replacing the Lamp
WARNING
Always disconnect power to the pool or spa white
light at the circuit breaker before servicing the
light. Failure to do so could result in death or
serious injury to installer, serviceman, pool or spa
users or others due to electrical shock.
1. Turn o the main electrical switch or circuit
breaker, as well as the switch, which operates the
underwater light.
Section 5. Wiring Options for
Controlling Jandy Pool or
Spa White Lights
NOTE: The Jandy Pool and Spa White Lights can
be dimmed when an optional Light Dimming
Module is added to the control system or control
switch.
To the extent allowed by code and capacity of theTo the extent allowed by code and capacity of the
electrical equipment, multipleelectrical equipment, multiple Jandy Pool and SpaJandy Pool and Spa
White LightsWhite Lights may be controlled with a single switch.may be controlled with a single switch.
5.1 Wiring to an AquaLink®RS Control
System
The Jandy Pool and Spa White Lights can be wired
into the Jandy AquaLink RS control system to provide
simplied operation of the lights. Connect the lights to
one of the auxiliary relays in the Power Center.
NOTE: It is recommended to connect one light per
relay so each light can be controlled separately.
However, up to four lights can be connected on
a single relay. If there are more than four lights
installed on one AquaLink RS system, ensure
there is more than one auxiliary relay available
in the Power Center.
Refer to Figures 3 and 4 to connect the Jandy Pool and
Spa White Lights to the Power Center.
WARNING
A Ground Fault Circuit Interrupter (GFCI) must be
provided for 120 volt models. The conductors on
the load side of the GFCI circuit shall not occupy
conduit, boxes, or enclosures containing other
conductors unless the additional conductors are
also protected by a GFCI. Refer to local codes for
complete details.
Jandy Model Fixture
Voltage
Lamp
Voltage
Lamp
Wattage Lamp Type Qty. per Fixture
Lamp Kit
Part Number
Pool/Spa White Light 12 Volt AC 12V 100 Watt R20 Flood 1 R0450501
Pool White Light 120 Volt AC 120V 300 Watt R40 Flood 1 R0450502
Pool White Light 12 Volt AC 12V 300 Watt R40 Flood 1 R0450503
Pool White Light 120 Volt AC 120V 500 Watt R40 Flood 1 R0450504
Spa White Light 120 Volt AC 120V 60 Watt 1 R0450505R20 Flood
Table 1. Lamp Specications

Page 11
ENGLISH
Jandy®Underwater Pool and Spa White Lights |Installation & Operation Manual
Align pilot screw with arrow
located on fixture label
Align arrow of the lens
with pilot screw
Figure 8. Alignment of the Lens, Face Ring, Housing and Clamps for Pool White Lights
2. Be sure to have the following items:
• A new lens gasket (P/N R0451101 for Jandy
Pool Light and P/N R0400501 for Jandy Spa
Light).
• One (1) new lamp. See Table 1 for
specications.
WARNING
Replace the lamp with one of the same type and
wattage. Failure to replace the lamp with one of
the same type will damage the light assembly and
may cause an electrical hazard resulting in death
or serious injury to pool or spa users, installers,
or others due to electrical shock, and may also
cause damage to property. Be sure the power is
switched OFF before removing or installing lamps.
Allow lamp to cool before replacing.
3. To remove the light assembly, unscrew the special
pilot screw at the top of the face ring, remove light
assembly from niche and gently place assembly on
the deck. It is not necessary to drain down the pool
or spa. See Figure 7.
4. Disassemble the light xture and replace lamp as
follows:
WARNING
Be sure to keep the special pilot screw from this
underwater light. This screw mounts and electrically
grounds the housing securely to the mounting ring
and wet niche. Failure to use the screw provided
could create an electrical hazard, which could
result in death or serious injury to pool or spa
users, installers or others due to electrical shock.
Figure 7. Removing the Pool and Spa White Light Assembly for Lamp Replacement
1
POOL WALL
POSITIONING TAB
TAB LOCATOR
Power
Cord Niche
PILOT SCREW
Push up on
bottom of
light assembly
2
Power
Cord Niche
SPA WALL
Unscrew pilot screw
and pull top of light
assembly away from
spa wall
1
PILOT SCREW
Push up on
bottom of
light assembly
2
POSITIONING TAB
TAB LOCATOR
Unscrew pilot screw
and pull top of light
assembly away from
pool wall
SPA WHITE LIGHT
ASSEMBLY
POOL WHITE LIGHT
ASSEMBLY
Bonding
cable
Bonding
cable

Page 12 ENGLISH Jandy®Underwater Pool and Spa White Lights | Installation & Operation Manual
c. Position the lens and gasket on the fixture. Placec. Position the lens and gasket on the fixture. Place
the face ring and the top clamp over the lens andthe face ring and the top clamp over the lens and
align the pilot screw with the small arrow markalign the pilot screw with the small arrow mark
on the face of the lens. Note that the small arrowon the face of the lens. Note that the small arrow
mark on the face of the lens and the pilot screwmark on the face of the lens and the pilot screw
of the face ring must be aligned with the arrowof the face ring must be aligned with the arrow
located on fixture label that reads, “Arrow on thislocated on fixture label that reads, “Arrow on this
label must line up with the pilot screw on the Facelabel must line up with the pilot screw on the Face
Ring”. See Figure 8.Ring”. See Figure 8.
d. While holding the aligned face ring assembly andd. While holding the aligned face ring assembly and
fixture together, turn the assembly upside downfixture together, turn the assembly upside down
and set it on the old gasket, using the old gasketand set it on the old gasket, using the old gasket
as an assembly fixture. This will keep the lens andas an assembly fixture. This will keep the lens and
gasket assembly from being pushed out of the facegasket assembly from being pushed out of the face
ring while you secure it to the light fixture.ring while you secure it to the light fixture.
e. Spread the bottom clamp over the electrical corde. Spread the bottom clamp over the electrical cord
and slide it onto the back of fixture to the topand slide it onto the back of fixture to the top
clamp. See Figure 8.clamp. See Figure 8.
f.f. Tighten the eight (8) Phillips head screws for pool
light or the six (6) Phillips head screws for spa
light in alternating cross-pattern. Torque screws to
approximately 20 in-lbs. Do not over-tighten.
g. Discard the old gasket.g. Discard the old gasket.
6. Reinstall the Jandy Light into niche xture.
a. Coil four (4) feet of cord around the fixture anda. Coil four (4) feet of cord around the fixture and
place the light assembly into the niche.place the light assembly into the niche.
b. Engage the retainer tab on the bottom of the faceb. Engage the retainer tab on the bottom of the face
ring, then pivot the top of the fixture inward andring, then pivot the top of the fixture inward and
tighten the special pilot screw.tighten the special pilot screw.
WARNING
Use only the special pilot screw provided with this
underwater light. This screw mounts and electrically
grounds the housing securely to the mounting ring
and wet niche. Failure to use the screw provided
could create an electrical hazard, which could
result in death or serious injury to pool or spa
users, installers or others due to electrical shock.
7. If pool or spa is empty, ll pool or spa until the
underwater light is completely submerged in
water before operating the light for more than 10
seconds. Turn on main switch or circuit breaker, as
well as the switch, which specically operates the
underwater light, to check for proper operation.
a. Loosen the eight (8) Phillips head screws for pool a. Loosen the eight (8) Phillips head screws for pool
light or the six (6) Phillips head screws for spalight or the six (6) Phillips head screws for spa
light to allow the bottom clamp to be removedlight to allow the bottom clamp to be removed
from the face ring assembly. Do not remove thefrom the face ring assembly. Do not remove the
screws or the retaining rings. The retaining ringsscrews or the retaining rings. The retaining rings
prevent the screws from falling free from the topprevent the screws from falling free from the top
clamp and also aid in ease of assembly.clamp and also aid in ease of assembly.
b. Remove the lower clamp, the face ring assembly,b. Remove the lower clamp, the face ring assembly,
the glass lens, and the gasket from the fixture.the glass lens, and the gasket from the fixture.
Remove the gasket from the lens. Refer toRemove the gasket from the lens. Refer to SectionSection
9, Exploded View and Replacement Parts9, Exploded View and Replacement Parts..
c. Install new lamp.c. Install new lamp.
WARNING
Risk of Electrical Shock or Electrocution.
Always install a new lens gasket whenever
disassembling the light (for Jandy Pool Light Gasket
P/N R0451101 and for Jandy Spa Light Gasket
P/N R0400501). Failure to do so may permit water
to leak into the assembly, which could cause:
(a) An electrical hazard resulting in death or
serious injury to pool or spa users, installers,
or others due to electrical shock, or
(b) Breakage of the lamp or lens, which likewise
could result in serious injury to pool or spa
users, installers, or bystanders, or in damage
to property.
5. Reassemble the xture as follows:
a. If not already done, remove the gasket from thea. If not already done, remove the gasket from the
glass lens and install a new gasket,glass lens and install a new gasket, Jandy PoolJandy Pool
LightLight GasketGasket (P/N R0451101) and (P/N R0451101) and Jandy SpaJandy Spa
Light GasketLight Gasket (P/N R0400501), on the lens. (P/N R0400501), on the lens.
NOTE: A new lens gasket must be used each time the
light is reassembled.
b. While holding the fixture upright, place the glassb. While holding the fixture upright, place the glass
lens with the gasket on top of the fixture. Pleaselens with the gasket on top of the fixture. Please
note that the lens gasket is not symmetrical.note that the lens gasket is not symmetrical.
Therefore, it must be installed correctly so thatTherefore, it must be installed correctly so that
the lens can seal to the fixture housing. Place thethe lens can seal to the fixture housing. Place the
gasket on the lens so that the thick molded sidegasket on the lens so that the thick molded side
of the gasket will mate with the housing when theof the gasket will mate with the housing when the
lens is installed. See Figure 11.lens is installed. See Figure 11.

Page 13
ENGLISH
Jandy®Underwater Pool and Spa White Lights |Installation & Operation Manual
WARNING
Never operate this underwater light for more than
10 seconds unless it is totally submerged in water.
Without total submersion, the light assembly will
get extremely hot, which may result in serious
burns or in breakage of the lamp or lens. This
may result in serious injury to pool or spa users,
installers, or bystanders or in damage to property.
Section 8. Twelve (12) Volt
Installation
A separate 12-Volt AC Transformer is required on all
12-Volt Models. Use an appropriately sized transformer
for your model light.
NOTE: For optimum performance Jandy recommends
to use one transformer per 12-volt light.
To ensure compliance with the National Electrical
Code®(NEC®) in the US (Canadian Electrical Code
(CEC) in Canada), and to reduce the risk of electric
shock which could result in serious injury or death, use
only a transformer that has been listed or recognized by
a Nationally Recognized Testing Laboratory (NRTL) for
pool/spa application.

Page 14 ENGLISH Jandy®Underwater Pool and Spa White Lights | Installation & Operation Manual
Section 9. Exploded View and Replacement Parts
9.1 Jandy Pool White Light
Figure 10. Jandy Pool White Light,
Front and Back View
Figure 11. Cross Section of Jandy Pool White Light
THICK MOLDED SIDE
OF THE GASKET MUST
MATE WITH THE BODY
OF THE HOUSING
Figure 9. Jandy Pool White Light Exploded View
24
3
16
657
88
99
DWG # Part # Description Field Replaceable
1N/A Pool Light Housing NO - Purchase New Light
2N/A Lamp Holder NO - Purchase New Light
3 R0450501 Lamp, 100 Watt, 12 Volt YES
3 R0450502 Lamp, 300 Watt, 120 Volt YES
3 R0450503 Lamp, 300 Watt, 12 Volt YES
3 R0450504 Lamp, 500 Watt, 120 Volt YES
4 R0451101 Silicone Gasket, Pool Light YES
5 R0450601 Glass Lens, Pool Light YES
6 R0450701 Clamp Assembly, Pool Light YES
7 R0450801 Face Ring, Stainless Steel (SS), Pool Light YES
7 R0450802 Face Ring, Plastic, White, Pool Light YES
7 R0450803 Face Ring, Plastic, Black, Pool Light YES
7 R0450804 Face Ring, Plastic, Gray, Pool Light YES
7 R0450805 Face Ring, Plastic Set, Pool Light YES
8 R0450901 Pilot Screw, with Retainer, Pool Light YES
9 R0451001 Clamp Screw (8 Screws and 8 Retainers) Pool Light YES

Page 15
ENGLISH
Jandy®Underwater Pool and Spa White Lights |Installation & Operation Manual
Figure 12. Jandy Spa White Light Exploded View
Figure 13. Jandy Spa White Light,
Front and Back View Figure 14. Cross Section of Jandy Spa White Light
24
3
16
6
57
88
99
DWG # Part # Description Field Replaceable
1N/A Spa Light Housing NO - Purchase New Light
2N/A Lamp Holder NO - Purchase New Light
3 R0450501 Lamp, 100 Watt, 12 Volt YES
3 R0450505 Lamp, 60 Watt, 120 Volt YES
4 R0400501 Silicone Gasket, Spa Light YES
5 R0400601 Glass Lens, Spa Light YES
6 R0451201 Clamp Assembly, Spa Light YES
7 R0451301 Face Ring, Stainless Steel (SS), Spa Light YES
7 R0451302 Face Ring, Plastic, White, Spa Light YES
7 R0451303 Face Ring, Plastic, Black, Spa Light YES
7 R0451304 Face Ring, Plastic, Gray, Spa Light YES
7 R0451305 Face Ring, Plastic Set, Spa Light YES
8 R0450901 Pilot Screw, with O-ring, Spa Light YES
9 R0451401 Clamp Screw (6 Screws and 6 Retainers) Spa Light YES
9.2 Jandy Spa White Light

ETL LISTED
CONFORMS TO
UL STD 1081
Certified to
CAN/CSA STD
C22.2 No. 108
Certified to
NSF/ANSI Standard 50
©2021 Zodiac Pool Systems LLC. All rights reserved. All other trademarks
referenced are the property of their respective owners.
H0312200_REVD
Zodiac Pool Systems LLC
2882 Whiptail Loop # 100
Carlsbad, CA 92010 USA
1.800.822.7933 | Jandy.com
Zodiac Pool Systems Canada, Inc.
3365 Mainway, Unit 2
Burlington, ON L7M 1A6 Canada
1.888.647.4004 | jandy.ca

Lampes blanches immergées de
piscine et de spa
H0312200_REVD
FRANÇAIS
MANUEL D’INSTALLATION ET
DE FONCTIONNEMENT
AVERTISSEMENT
POUR VOTRE SÉCURITÉ, ce produit doit être installé et entretenu par un entrepreneur disposant d'une
licence et qui est qualifié en équipements de piscine par la juridiction dans laquelle le produit est installé
lorsque de telles exigences étatiques ou locales existent. L'agent d'entretien doit être un professionnel
disposant de suffisamment d'expérience dans l'installation et l'entretien des équipements de piscine afin de
s'assurer que toutes les directives du présent manuel sont scrupuleusement respectées. Avant d'installer
ce produit, lire et suivre tous les avertissements et toutes les directives qui accompagnent ce produit. Dans
le cas contraire, des dommages matériels ou des blessures, possiblement mortelles, peuvent survenir. Une
mauvaise installation et/ou un mauvais fonctionnement annulent la garantie.
Une mauvaise installation et/ou un mauvais fonctionnement peuvent engendrer un danger
électrique pouvant entraîner des dommages matériels ou des blessures graves, voire mortelles.
À L'ATTENTION DE L'INSTALLATEUR - Ce manuel contient des informations importantes sur
l'installation, le fonctionnement et l'utilisation sécuritaire de ce produit. Ces informations
doivent être communiquées au propriétaire ou à l'exploitant de cet équipement.

Page 18 FRANÇAIS Jandy® Lampes blanches immergées de piscine et de spa | Manuel d’installation et de fonctionnement
Table des matières
Section 1. Consignes de sécurité ......................19
Section 2. Description du produit et numéros
de modèles .........................................20
Section 3. Installation d’une lampe Jandy
sur un chantier de construction .......21
3.1 Préparation de la lampe pour l’installation .......21
3.2 Installation de la lampe ....................................22
Section 4. Remplacement d’une lampe
Jandy dans une piscine ou un
spa existants.......................................23
4.1 Préparation de la lampe
pour son remplacement ...................................23
4.2 Remplacement de la lampe .............................23
Section 5. Options de câblage pour contrôler
les lampes blanches de piscine
et de spa Jandy ..................................25
5.1 Câblage à un système de contrôle
RS Aqualink®....................................................25
5.2 Câblage à une horloge ....................................25
5.3 Câblage à un interrupteur ................................25
Section 6. Consignes d’utilisation .....................27
6.1 Pour faire fonctionner la lampe ........................27
Section 7. Remplacement de la lampe ..............27
Section 8. Installation 12 volts ...........................29
Section 9. Vue éclatée et pièces
de rechange .......................................30
9.1 Lampe blanche de piscine Jandy .....................30
9.2 Lampe de spa blanche Jandy...........................31

Page 19
FRANÇAIS
Jandy® Lampes blanches immergées de piscine et de spa | Manuel d’installation et de fonctionnement
Section 1. Consignes de sécurité
DIRECTIVES DE SÉCURITÉ IMPORTANTES RELATIVEMENT
À UN RISQUE D’INCENDIE, DE CHOC ÉLECTRIQUE,
OU DE BLESSURES AUX PERSONNES.
LIRE ET SUIVRE TOUTES LES DIRECTIVES
Lors de l’installation et de l’utilisation de cet équipement électrique, des précautions de base doivent toujours être
suivies, entre autres :
AVERTISSEMENT
RISQUE DE CHOC ÉLECTRIQUE OU D’ÉLECTROCUTION. Cette lampe immergée doit être installée par
un technicien breveté ou certié en accord avec le Code national d’électricité américain (NEC®) et le Code
électrique canadien (CEC) et avec les autres codes et arrêtés locaux applicables. Une installation incorrecte
peut entraîner un risque de problème électrique (choc électrique ou électrocution) pouvant causer des
blessures graves et même la mort des installateurs ou utilisateurs du spa et de la piscine. Lisez et respectez
les instructions détaillées ci-dessous.
AVERTISSEMENT
Avant d’installer la lampe immergée, lisez et respectez toutes les consignes d’avertissement et instructions
incluses avec cette lampe. Toute e󰀨raction à ces consignes de sécurité et instructions peut causer des
blessures graves ou mortelles, ou des dommages matériels. Composez le (+1) [phone] pour recevoir
gratuitement des manuels supplémentaires des consignes de sécurité.
MISE EN GARDE
La lampe doit être installée à l’intérieur de la paroi ou sur la paroi de la piscine de façon à ce que le bord
supérieur du verre de protection soit situé à au moins 18 pouces (457 mm) au-dessous du niveau normal de
l’eau de la piscine, à moins que les lampes de piscine et de spa Jandy ne soient installées dans une partie de
la piscine non utilisée pour la baignade et que les lentilles soient protégées adéquatement pour empêcher toute
personne d’y toucher.
À L’ATTENTION DE L’INSTALLATEUR : ce guide contient des informations importantes
concernant l’installation, le fonctionnement et les consignes de sécurité de ce produit.
Ces informations doivent être données au propriétaire/opérateur de ce matériel.
CONSERVEZ CES DIRECTIVES

Page 20 FRANÇAIS Jandy® Lampes blanches immergées de piscine et de spa | Manuel d’installation et de fonctionnement
Section 2. Description du produit et numéros de modèles
Numéro de modèle
Jandy
Taille de la lampe
blanche Jandy Tension Watts maximum
Longueur
du câble
Matériau de la
bague avant
WPLV100WS30 Piscine 12 Volts CA 100 30 pieds (approx. 9 m) Acier inoxydable
WPLV100WS50 Piscine 12 Volts CA 100 50 pieds (approx.15 m) Acier inoxydable
WPLV100WS100 Piscine 12 Volts CA 100 100 pieds (approx. 30 m) Acier inoxydable
WPLV100WS50C Piscine (Canada) 12 Volts CA 100 50 pieds (approx.15 m) Acier inoxydable
WPLV100WS100C Piscine (Canada) 12 Volts CA 100 100 pieds (approx. 30 m) Acier inoxydable
WPLV300WS30 Piscine 12 Volts CA 300 30 pieds (approx. 9 m) Acier inoxydable
WPLV300WS50 Piscine 12 Volts CA 300 50 pieds (approx.15 m) Acier inoxydable
WPLV300WS100 Piscine 12 Volts CA 300 100 pieds (approx. 30 m) Acier inoxydable
WPLV300WS50C Piscine (Canada) 12 Volts CA 300 50 pieds (approx.15 m) Acier inoxydable
WPLV300WS100C Piscine (Canada) 12 Volts CA 300 100 pieds (approx. 30 m) Acier inoxydable
WPHV300WS30 Piscine 120 Volt CA 300 30 pieds (approx. 9 m) Acier inoxydable
WPHV300WS50 Piscine 120 Volt CA 300 50 pieds (approx.15 m) Acier inoxydable
WPHV300WS100 Piscine 120 Volt CA 300 100 pieds (approx. 30 m) Acier inoxydable
WPHV300WS150 Piscine 120 Volt CA 300 150 pieds (approx. 45 m) Acier inoxydable
WPHV300WS250 Piscine 120 Volt CA 300 250 pieds (approx. 75 m) Acier inoxydable
WPHV300WS50C Piscine (Canada) 120 Volt CA 300 50 pieds (approx.15 m) Acier inoxydable
WPHV300WS100C Piscine (Canada) 120 Volt CA 300 100 pieds (approx. 30 m) Acier inoxydable
WPHV500WS30 Piscine 120 Volt CA 500 30 pieds (approx. 9 m) Acier inoxydable
WPHV500WS50 Piscine 120 Volt CA 500 50 pieds (approx.15 m) Acier inoxydable
WPHV500WS100 Piscine 120 Volt CA 500 100 pieds (approx. 30 m) Acier inoxydable
WPHV500WS150 Piscine 120 Volt CA 500 150 pieds (approx. 45 m) Acier inoxydable
WPHV500WS250 Piscine 120 Volt CA 500 250 pieds (approx. 75 m) Acier inoxydable
WPHV500WS50C Piscine (Canada) 120 Volt CA 500 50 pieds (approx.15 m) Acier inoxydable
WPHV500WS100C Piscine (Canada) 120 Volt CA 500 100 pieds (approx. 30 m) Acier inoxydable
WPLV100WP100 Piscine 12 Volts CA 100 100 pieds (approx. 30 m) Plastique
WPLV300WP100 Piscine 12 Volts CA 300 100 pieds (approx. 30 m) Plastique
WPHV300WP100 Piscine 120 Volt CA 300 100 pieds (approx. 30 m) Plastique
WPHV500WP100 Piscine 120 Volt CA 500 100 pieds (approx. 30 m) Plastique
WSLV100WS30 Spa 12 Volts CA 100 30 pieds (approx. 9 m) Acier inoxydable
WSLV100WS50 Spa 12 Volts CA 100 50 pieds (approx.15 m) Acier inoxydable
WSLV100WS100 Spa 12 Volts CA 100 100 pieds (approx. 30 m) Acier inoxydable
WSLV100WS50C Spa (Canada) 12 Volts CA 100 50 pieds (approx.15 m) Acier inoxydable
WSLV100WS100C Spa (Canada) 12 Volts CA 100 100 pieds (approx. 30 m) Acier inoxydable
WSHV100WS30 Spa 120 Volt CA 100 30 pieds (approx. 9 m) Acier inoxydable
WSHV100WS50 Spa 120 Volt CA 100 50 pieds (approx.15 m) Acier inoxydable
WSHV100WS100 Spa 120 Volt CA 100 100 pieds (approx. 30 m) Acier inoxydable
WSHV100WS150 Spa 120 Volt CA 100 150 pieds (approx. 45 m) Acier inoxydable
WSHV100WS250 Spa 120 Volt CA 100 250 pieds (approx. 75 m) Acier inoxydable
WSHV100WS50C Spa (Canada) 120 Volt CA 100 50 pieds (approx.15 m) Acier inoxydable
WSHV100WS100C Spa (Canada) 120 Volt CA 100 100 pieds (approx. 30 m) Acier inoxydable
WSLV100WP100 Spa 12 Volts CA 100 100 pieds (approx. 30 m) Plastique
WSHV100WP100 Spa 120 Volt CA 100 100 pieds (approx. 30 m) Plastique