Jason.L Just Right User manual

Just Right height
adjustable corner desk

2
1
3
45
6
7
9
10
1
2
3
A
E
8
11
12
14
Cx6
AB
x1 D
x7
x18
F
x8 x1
Wrench
G
M6
5x5 2.5x2.5 M8
ST4.2
M4
4x4
Ex12
M6
Ex12
A
5x5 8
1A
4
F
3
2
2
x7
F
4x4
A
5x5
1
5
Right Column X1 Middle Column X1 Left Column X1 Long Supporting
Beam X1
Long Transmission
Rod X1
Short Transmission
RodX1
Table Leg X3
Short Supporting
Beam X1
Baffle X4 Control Box X1
6 7 8 11
9
1 2 3 4 5
11
10
11
13 14
Handset X1
Long Supporting
Plate X2
11
11
Short Supporting
Plate X1
11
12
Power Cable X1
13
A
4
15
Cable Tie X4
15
8
8
F
F
E
E
100KG
25mm/s
100-240V
710mm
1210mm
0~40°C
2
1020-1600mm
1075-1575mm
Technical data
Column Number
Maximum Load
Max Speed
Input Voltage
Lowest Position
Highest Position
Width Range
Duty Cycle
Applicable Temperature
10%(Pause 18 minutes for each
continuous 2-minute operation )
Accessory List
Attention: The drawings below are only for reference which might be slightly different from the physical objects, please refer to the actual product. If there are
any tools missing or installation problems, please contact customer service.
Part List
STEP1
STEP2
Installation Instruction
Assemble Table Legs
Connect the table legs (8) to the columns (1), (2), and (3), fix them with
screws (E), and tighten them with the 5 x 5 allen key (A).
Install Supporting Beam
Unscrew
Stretch
Loose screws on the long supporting beam (4) with the 4x4
allen key (A), then stretch supporting beam.
The operation of the short beam (5) is the same as above.
Install supporting beams (4)(5) on the column(1) (2)(3),
tighten the screw (F) with the 5x5 allen key (A).

C
A
2
3
Cx6
A
5x5
1
9
2.5x2.5
A
7
6
14
13
Dx16
D
12
54
2
10
2 4
3
13
A
A
9
STEP3 STEP4
STEP5-A
STEP5-B
Install Transmission Rod
Unscrew
Insert
Tighten
Spin
Unscrew
Insert
Insert
Insert
Tighten
Spin
The rotation angle should not exceed
one third of a turn.
Insert the long and short transmission rods (6) (7) into the left, middle
and right columns (1) (2) (3) respectively, and use the 2.5 x 2.5 allen
key (A) to screw the long and short transmission rods (6) (7) .
Install Supporting Plates
Connect the long supporting plate (9) to the columns (1) (3), connect the short
supporting plate(10) to the column(2). fix them with the screw (C) and tighten the
screw by 5X5 allen key(A).
Install Tabletop, Control Box
and Handset
Not provided
Adjust the length of the beam (4) (5) according
to the size of the table board
The distance between the two sides
shall not be longer than 200 mm
Connect the tabletop and the handset (13) with screws (D),
fix the control box (12)on the tabletop with its own screws,
and tighten it with a pistol drill.
The control box shall be placed
near the middle of the table to
ensure that the motor wire can be
connected to the control box.
Self-owned
screw
Attach connector plates (a) to return top (b) by tightening wooden screws (c)

A
4x4
G
A
54
A
7
6
G
G
STEP6 Tighten the Beam Screw and the
Drive Rod Nut
Use the 4 x 4 allen key (A) to tighten the 8 screws on the long
and short beams (4) (5), and use the nut wrench (G) to tighten
the nuts on the long and short transmission rods (6) (7).
14
12
13
Bx8
A
2.5x2.5
15
15
15
15
A
11 B
5
11
4
STEP7
STEP8
Install Baffle
Install the baffle (11) on the long and short beams (4) (5)
with screws (B), and tighten it with a 2.5 x 2.5 allen key(A).
Connect all Cable on to the Control Box
Do not connect the power before the wiring is completed.
You can use the cable tie (15) to
sort out the cables on the table
to keep the cables tidy.
Tear off Manage cable Fix
Port for
handset
Power port
Port for cable
connected to the
lifting column
Attention
1. Power supply: AC100V-240V,50/60Hz
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet
dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose
the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so
dispose of it in accordance with each country's environmental legislation, not the
general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the product because of unforeseen action when
playing, so any dangerous consequences caused by this improper action will not be on
manufacturers.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not
have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure
that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g.,
do not litter the tools around. Always be careful to treat the packaging materials in order
to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in
transportation.
Common fault treatment
The following tips will help you detected and eliminate the common
fault and error. If the error you meet is not on the list, please contact
our customer service.
Error Method
No response while pressing
The desktop moving towards
the opposite direction as ordered
Rising in a low speed
The desk moving downwards
without any operation
Automatically Self-Reset
Overload Operation
Can’t reach the min or max height
Check if all the cables well connected;
Reset;
Check if overloaded, max loading: 100kg;
Check if overloaded, max loading: 100kg;
Check if overloaded, max loading: 100kg;
Restart after suspend for 18mins while
connecting with power;
Reposition;