Jason.L Quadro A Legs 3P 120 Degree Workstation with... User manual

Need help!
Call us on
1300 527 665
www.jasonl.com.au
Tools Required: Power screwdriver; Allen key set (provided)
2 persons required for installation
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs
3P 120 Degree
Workstation with Screens
Sizes: 1200x1200x700 mm
Page 1 of 10

Table top x3
Leg Quadro x3
Leg Quadro Loop x3
Connector frame x3
Beam x6
Plastic bracket x24
A
B
C
D
E
F
Allen keyK
M8x20MM CSK x12
M8x20MM Socket head x12
M6x20MM Socket head x24
Washers and chipboard screws x24
G
H
I
J
COMPONENTS
SCREWS
Need help!
Call us on
1300 527 665
www.jasonl.com.au
E
F
G H I J
B
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs
3P 120 Degree
Workstation with Screens
Sizes: 1200x1200x700 mm
A
D
Page 2 of 10
C

Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLED
WORKSTATION
TOP VIEW
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs
3P 120 Degree
Workstation with
Screens
Sizes: 1200x1200x700 mm
E
F
A
B
D
Page 3 of 10

Page 4 of 10
Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs
3P 120 Degree
Workstation with Screens
Sizes: 1200x1200x700 mm
H
STEP 02
I
STEP 01
Using Allen Key provided, attach 4 plastic brackets per leg (F)
(as per picture above) using M6x20MM (I) Socket head screw.
Do the same with Connector frame (D). Connect Loop Legs (C)
to Bottom of Quadro Legs (B) by using 4 bolts per leg
Using Allen Key provided, attach M8x20MM Socket head (H)-
screw socket half way into leg for both legs (B) and into
Connector frame (D).

STEP 03
Adjust extendable beam (E) to
desired length using markers and
secure beam at that length using
screws provided
Need help!
Call us on
1300 527 665
www.jasonl.com.au
800
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs
3P 120 Degree
Workstation with Screens
Sizes: 1200x1200x700 mm
Page 5 of 10

STEP 04
TOP VIEW
Attach beam (E) to legs (B) using nut
insert in legs. See point attached
Frame looks like this. Using Allen Key, attach beam (E) with Socket (G)
STEP 05
Need help!
Call us on
1300 527 665
www.jasonl.com.au
G
G
G
G
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs
3P 120 Degree
Workstation with Screens
Sizes: 1200x1200x700 mm
B
B
D
Page 6 of 10

Need help!
Call us on
1300 527 665
www.jasonl.com.au
Pleace desktop on top of the frame leaving a 25mm gap between
them. Tops will need to be drilled using 30mm chipboard screws.
Please put washers underneath the plastic brackets hole before
drilling the screws into the Tops.
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs
3P 120 Degree
Workstation with Screens
Sizes: 1200x1200x700 mm
STEP 06
TOP VIEW
J
Page 7 of 10

STEP 07
Drop the desk mounted screen in between the two tops (A). Now please
insert 2 rod brackets that will hold each screen to the desks on either side.
Need help!
Call us on
1300 527 665
www.jasonl.com.au
25 mm
AA
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs
3P 120 Degree
Workstation with Screens
120 Degree table top size: 1200x1200x700 mm
Page 8 of 10

Need help!
Call us on
1300 527 665
www.jasonl.com.au
A
STEP 08
Second person to drill 4 holes into the brackets holes with provided wood screws into the underneath desktop. Please check the position of the
rod brackets and bracket holes again before drilling the screws all the way through. Please tighten all the wood screws.
Once the 2 rod brackets are screwed in, you can slide the screen down until it fully rest over the brackets, standing between both table tops.
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs
3P 120 Degree
Workstation with Screens
120 Degree table top size: 1200x1200x700 mm
Page 9 of 10

STEP 09
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Using an allen key, please remove 3 caps from all screens. Bring 3 partitions towards one another and slide the 3-way 120 degree connector
-down between the three screen uprights.
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs
3P 120 Degree
Workstation with Screens
120 Degree table top size: 1200x1200x700 mm
Page 10 of 10