Jason.L Quadro Loop Legs 6P 120 Degree Workstation with... User manual

Page 1 of 10
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Tools Required: Power screwdriver; Allen key set (provided)
2 persons required for installation
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs 6P
120 Degree Workstation
with Screens
Sizes: 1200x1200x700 mm

Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs 6P
120 Degree Workstation
with Screens
Sizes: 1200x1200x700 mm
Table top x6
Leg Quadro x4
Leg Quadro Loop x6
Connector frame x7
Beam x12
Plastic bracket x48
A
B
C
D
E
F
Allen keyK
M8x20MM CSK x24
M8x20MM Socket head x24
M6x20MM Socket head x48
Washers and chipboard screws x48
G
H
I
J
COMPONENTS
SCREWS
E
F
G H I J
B
D
Page 2 of 10
C
A

Page 3 of 10
Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLED
WORKSTATION
TOP VIEW
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs 6P
120 Degree Workstation
with Screens
Sizes: 1200x1200x700 mm
E
F
A
B
D

Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs 6P
120 Degree Workstation
with Screens
Sizes: 1200x1200x700 mm
Page 4 of 10
H
STEP 02
I
STEP 01
Using Allen Key provided, attach 4 plastic brackets per leg (F)
(as per picture above) using M6x20MM (I) Socket head screw.
Do the same with Connector frame (D). Connect Loop Legs (C)
to Bottom of Quadro Legs (B) by using 4 bolts per leg
Using Allen Key provided, attach M8x20MM Socket head (H)-
screw socket half way into leg for both legs (B) and into
Connector frame (D).

STEP 03
Please set extendable beam (E) to
800mm length and secure beam at
that length using screws provided
Page 5 of 10
Need help!
Call us on
1300 527 665
www.jasonl.com.au
800
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs 6P
120 Degree Workstation
with Screens
Sizes: 1200x1200x700 mm

Need help!
Call us on
1300 527 665
www.jasonl.com.au
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs 6P
120 Degree Workstation
with Screens
Sizes: 1200x1200x700 mm
STEP 04
TOP VIEW
Attach beam (E) to legs (B) using nut
insert in legs. See point attached
Frame looks like this. Using Allen Key, attach beam (E) with Socket (G)
STEP 05
G
G
G
G
B
E
B
D
Page 6 of 10

Page 7 of 10
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Pleace desktop on top of the frame leaving a 25mm gap between
them. Tops will need to be drilled using 30mm chipboard screws.
Please put washers underneath the plastic brackets hole before
drilling the screws into the Tops.
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs 6P
120 Degree Workstation
with Screens
Sizes: 1200x1200x700 mm
STEP 06
I
TOP VIEW

STEP 07
Drop the desk mounted screen in between the two tops (A). Now please
insert 2 rod brackets that will hold each screen to the desks on either side.
Need help!
Call us on
1300 527 665
www.jasonl.com.au
25 mm
AA
Page 8 of 10
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs 6P
120 Degree Workstation
with Screens
120 Degree table top size: 1200x1200x700 mm

Need help!
Call us on
1300 527 665
www.jasonl.com.au
A
STEP 08
Page 9 of 10
Second person to drill 4 holes into the brackets holes with provided wood screws into the underneath desktop. Please check the position of the
rod brackets and bracket holes again before drilling the screws all the way through. Please tighten all the wood screws.
Once the 2 rod brackets are screwed in, you can slide the screen down until it fully rest over the brackets, standing between both table tops.
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs 6P
120 Degree Workstation
with Screens
120 Degree table top size: 1200x1200x700 mm

STEP 09
Need help!
Call us on
1300 527 665
www.jasonl.com.au
Using an allen key, please remove 3 caps from all screens. Bring 3 partitions towards one another and slide the 3-way 120 degree connector
-down between the three screen uprights.
Page 10 of 10
ASSEMBLY INSTRUCTIONS
Quadro Loop Legs 6P
120 Degree Workstation
with Screens
120 Degree table top size: 1200x1200x700 mm