Jenn-Air JGD3430W Parts list manual

30" (76.2 CM) AND 36" (91.4 CM) GAS DOWNDRAFT COOKTOP
PRODUCT MODEL NUMBERS CUTOUT DIMENSIONS
JGD3430W
JGD3536W
AB
CD
E
F
G
H
I
J
30" (76.2 cm) Cooktop
A. 21½" (54.6 cm)
B. 19
¹¹⁄₁₆ " (50.0 cm)
C. Model/serial rating plate location
C
A
B
A. 30" (76.2 cm)
B. 12
¹⁵⁄₁₆ " (32.9 cm) centerline of
cooktop to centerline of gas
manifold pipe
C. 4" (10.2 cm)
D. 6
¹⁹⁄₃₂ " (16.8 cm)
E. 18
⁷⁄₁₆ " (46.8 cm)
F. 1
¹¹⁄₁₆ " (4.3 cm) recommended
minimum cabinet to motor
clearance
G. 12
¹⁄₂
" (31.8 cm)
H. 14" (35.6 cm)
I. 28¼" (71.4 cm)
AB
C
D
E
F
GH
I
PRODUCT DIMENSIONS
GAS SUPPLY
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local codes
and ordinances. In the absence of local codes, installation must
conform with American National Standard, National Fuel Gas Code
ANSI Z223.1 - latest edition or CAN/CGA B149 - latest edition.
Type of Gas
Natural Gas:
This cooktop is design-certified by CSA International for use with
Natural gas or, after proper conversion, for use with LP gas.
● This cooktop is factory set for use with Natural gas. If converting to
LP gas, see the “LP Gas Conversion” instructions provided in the
package containing literature. The model/serial rating plate located on
the underside of the cooktop base has information on the types of
gas that can be used. If the types of gas listed do not include the
type of gas available, check with the local gas supplier.
LP Gas Conversion:
Conversion must be done by a qualified service technician. No attempt
shall be made to convert the cooktop from the gas specified on the
model/serial rating plate for use with a different gas without consulting
the serving gas supplier. See the Gas Conversion instructions provided
in the package containing literature.
● A120 volt, 60 Hz, AC only, 15-amp, fused electrical circuit is
required. A time-delay fuse or circuit breaker is also recommended. It
is recommended that a separate circuit serving only this cooktop be
provided.
ELECTRICAL
Ref. W10197058A

CABINET DIMENSIONS
B
D
A
EF
H
I
K
L
K
M
M
C
G
N
J
A. 30" (76.2 cm) on 30" (76.2 cm) models
36" (91.4 cm) on 36" (91.4 cm) models
B. Combustible area above countertop (shown by dashed box above)
C. 30" (76.2 cm) minimum clearance between top of cooktop platform and
bottom of uncovered wood or metal cabinet (24" [61.0 cm] minimum
clearance if bottom of wood or metal cabinet is covered by not less
than ¹⁄₄" [0.6 cm] flame retardant millboard covered with not less than
No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless steel, or 0.024"
[0.06 cm] aluminum or 0.020" [0.05 cm] copper)
D. 13" (33.0 cm) recommended upper cabinet depth
E. 2¹⁄₈" (5.4 cm)
F. 19¹⁵⁄₁₆" (50.6 cm)
G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop
within minimum horizontal clearances to cooktop
H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of
countertop
I. Junction box or outlet; 10" (25.4 cm) from right-hand side of
cabinet
J. 28⁵⁄₈" (72.7cm) on 30" (76.2 cm) models
34³⁄₄ (88.3 cm) on 36" (91.4 cm) models
K. 6" (15.2 cm) minimum distance to nearest left and right side
combustible surface above cooktop
L. 1" (2.5 cm) minimum clearance between back wall and countertop
M. Gas line opening - Wall: anywhere 6" (15.2 cm) below underside of
countertop. Cabinet floor: anywhere within 6" (15.2 cm) of rear wall
is recommended.
N. 25" (63.5 cm) depth of countertop
NOTES: After making the countertop cutout, some installations may require
notching down the base cabinet side walls to clear the cooktop base. To avoid this
modification, use a base cabinet with sidewalls wider than the cutout.
● A minimum side clearance of 6" (15.2 cm) is recommended between side of
cooktop and side wall for maximum ventilation performance.
● A minimum clearance of 2" (5.1 cm) is recommended between the motor/blower
and cabinet for proper cooling. A 6" (15.2 cm) clearance is recommended for
servicing access.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice. Ref. W10197058A
08-14-2009
36" (91.4 cm) Cooktop
B. 19 ¹¹⁄₁₆ " (50.0 cm)
C. Model/serial rating plate location
A. 36" (91.4 cm)
cooktop to centerline of gas
manifold pipe
C. 4" (10.2 cm)
D. 6
¹⁹⁄₃₂ " (16.8 cm)
E. 18
⁷⁄₁₆ " (46.8 cm)
F. 1 0
³⁄₈ " (26.4 cm)
recommended minimum
cabinet to motor clearance
G. 12
¹⁄₂ " (31.8 cm)
H. 13" (33.0 cm)
I. 34
³⁄₈ " (87.3 cm)
C
A
B
AB
D
C
E
FI
GH