Jet 1/2DS-3C-10 User manual

jettools.com
DS ELECTRIC HOIST
STOCK NO. 900474
10M 07/05
©2005 WMH TOOL GROUP, Inc. All Rights Reserved.
Designed for commercial and industrial applications the
JET Dual Speed Electric Hoists are easy to install, inspect,
and maintain. Each comes equipped with a heavy duty
ventilated motor available in a range of HP from 1-1/5 to
2-1/7. Gear trains feature lifetime lubrication eliminating
the need for oil changes. All models come standard with slip
clutch overload protection, chain containers, and drop forged,
heat treated hooks that swivel 360 degrees for easy rigging.
Quick connect wiring for power and push button controls allow
for quick set-up while the DC electromagnetic brake secures
loads even if power is interrupted.
For added convenience and versatility equip the DS Series
Electric Hoists with a JET ET series Electric Trolley.
Available in a variety of capacities the ET Electric Trolley
features the same quick-connect cords as the DS Electric
Hoists allowing for fast set-up and installation.

jettools.com
DS ELECTRIC HOIST
1 HP Totally Enclosed
Fan cooled Motor
Front Mounted Table
Adjustment Dials
DS DUAL SPEED ELECTRIC HOIST
• Designed for commercial and industrial applications
• 1/2-ton to 5-ton capacities, single or three phase models
• 10', and 20' lifts standard, custom length lifts available
• Slip clutch design overload protection
• Easy to install, inspect and maintain
• Totally enclosed steel plate construction with a durable powder coat finish
• Gear train features lifetime lubrication, no oil changes required
• Heavy-duty ventilated motor
• All models feature reverse phase protection and thermal overload protection
• Can be operated on 50Hz power with 20% reduction in lifting speed
• All hoists come standard with chain container
• Drop forged, heat treated hooks swivel 360° for easy rigging
• Reliable DC electro-magnetic brake holds the load even if power is interrupted
• Quick-connect wiring for power and push button controls
• Upper and lower limit switches prevent over-travel
• Durable low voltage 24V push button control station with cable strain relief
• Proof tested with test certificate
• Compliance: OSHA, ANSI / ASME B30.16 and HST-1 standards.
• All models rated H3 with 25% duty cycle rating for 1-phase and 30% duty cycle rating
for 3-phase models
• 15% duty cycle rating = 9 minutes continuous in 1 hour, or 1 minute on, 7 minutes off
• 25% duty cycle rating = 12 minutes continuous in 1 hour, or 1 minute on,
4 minutes off
• 30% duty cycle rating = 18 minutes continuous in 1 hour, or 1 minute on,
4 minutes off
STOCK
NUMBER
MODEL
NUMBER
STANDARD
LIFT
HEADROOM
(IN)
DUTY
CYCLE
DUTY
CYCLE
RATING
LIFTING
SPEED/FT PER
MINUTE
MOTOR
OUTPUT
(HP)
RATED
AMPS
230V
RATED
AMPS
460V
LOAD CHAIN
DIAMETER
(MM)
NUMBER
OF
FALLS
GROSS
WEIGHT
(LBS)
503100 1/2DS-3C-10 10ft 20-3/16 30%,15% H3 31.5, 10.5 1-1/5 3.5, 1.8 4.7, 2.4 8x24 1 108
503200 1/2DS-3C-20 20ft 20-3/17 30%,15% H3 31.5, 10.5 1-1/5 3.5, 1.8 4.7, 2.4 8x24 1 114 1/2
103100 1DS-3C-10 10ft 24-7/16 30%,15% H3 24.8, 8.3 2-1/7 5.9, 3 6.9, 3.5 8x24 1 169 1/2
103200 1DS-3C-20 20ft 24-7/16 30%,15% H3 24.8, 8.3 2-1/7 5.9, 3 6.9, 3.5 8x24 1 180 1/2
203100 2DS-3C-10 10ft 28-1/8 30%,15% H3 12.4, 4.1 2-1/7 5.9, 3 6.9, 3.5 8x24 2 185
203200 2DS-3C-20 20ft 28-1/8 30%,15% H3 12.4, 4.1 2-1/7 5.9, 3 6.9, 3.5 8x24 2 205
303100 3DS-3C-10 10ft 31-1/2 30%,15% H3 8.3, 2.8 2-1/7 5.9, 3 6.9, 3.5 8x24 3 216
303200 3DS-3C-20 20ft 31-1/2 30%,15% H3 8.3, 2.8 2-1/7 5.9, 3 6.9, 3.5 8x24 3 244 1/2
531010 5DS-3C-10 10ft 30-11/16 30%,15% H3 6.2, 2.1 2-1/7 5.9, 3 6.9, 3.5 8x24 4 236
532020 5DS-3C-20 20ft 30-11/16 30%,15% H3 6.2, 2.1 2-1/7 5.9, 3 6.9, 3.5 8x24 4 275 1/2