Jimi LL701 User manual

LL701
User Manual
Version: V1.0
Read this manual carefully prior to use to ensure fast
and correct operation of the product. No prior notice
will be given for any changes made to the appearance,
color, or accessories of the product.

Product Overview
Standard Parts List
Item Quantity
LL701 1
Magnetic mount 1
Double-sided tape 1
Batteries 3

Speci󽗉cation
GNSS
Cellular
Positioning system
GPS+LBS+WiFi+Bluetooth
GPS+WiFi+Bluetooth
GPS+WiFi+Bluetooth, LBS (optional)
Frequency GPS L1 C/A supported
QZSS L1 C/A supported
Positioning accuracy < 2.5m CEP
Tracking sensitivity –155dBm
Acquisition sensitivity –145.5 dBm (cold start); –147 dBm (hot start)
TTFF (open sky) Avg. hot start: ≤ 1 second
Avg. cold start: ≤ 36 seconds
Communication network LTE
Frequency bands
LTE CAT-M1:
B1, B2, B3, B4, B5, B8, B12, B13, B14, B18,
B19, B20, B25, B26, B28, B66
LTE CAT-NB1/NB2:
B1, B2, B3, B4, B5, B8, B12, B13, B17, B19,
B20, B25, B26, B28, B66

Product Setup
・Open the socket lid;
・Place the SIM card into the socket (metal side downward);
・Close the socket lid (if the SIM card is incorrectly placed, the lock will fail).
LED Indication
When the device runs in recycling mode, press its function button ⑤ for 3 seconds
and the power LED ② will light on for 4 seconds to tell you the strength of the internal
battery.
Battery Indication
Power
Interface
Working modes
Mode 1: Power-saving mode
Mode 2: Regular GPS mode
Mode 3: Power-o󽗈 mode
Standby time Up to 5 years (one 󽗉x per day)
LED indication GNSS (Blue), Cellular (Green), Power (Red)
SIM Micro-SIM
Tamper proof Light sensor

LED Status Battery Strength Min. standby time
4 LEDs on 80% to 100% 1550 days
3 LEDs on 50% to 79% 950 days
2 LEDs on 30% to 49% 550 days
1 LED on 10% to 29% 190 days
1 󽗊ashing LED 1% to 9% Exhausting
Note:
The min. standby time is estimated on the ground that the device generates
one 󽗉x per day.
The GNSS LED ③ is used to show the working status of the device's GNSS module,
where:
・Flashing rapidly [on–o󽗈 (0.1s–0.1s)]: The device is searching for satellite signals;
・Always on: A position has been 󽗉xed;
・O󽗈: The GNSS module isn't working.
The cellular LED ④ is used to show the network status of the device, where:
・Flashing slowly [on–o󽗈 (0.1s–0.5s)]: The device is identifying the SIM card;
・Flashing rapidly [on–o󽗈 (0.1s–0.1s)]: The device is receiving cellular signals;
・Flashing slowly [on–o󽗈 (0.1s–0.1s)]: The device is online;
・O󽗈: The device fails to receive cellular signals or no SIM card is identi󽗉ed.
GNSS Indication
Cellular Indication

Con󽗉guration
Command: APN,<N>[,U][,P]#
N: Network name
U: User name
P: User password
Note: The parameters "U" and "P" can be left empty. The command is "CMNET#" by
default.
APN adaptation switch: ASETAPN,<SW>#
SW: Switch to enable or disable the APN adaptation feature, whose value is either
"ON" or "OFF".
Note: The default value for "SW" is "ON". Comparing these two setting methods, the
priorities of manually-set APNs are higher than the self-adapted ones. Once an APN is
manually changed (via a command sent by the user), the adaptation feature will turn
invalid (auto switched to OFF). This auto switch-o󽗈 protects the device against failing
to go online in the event of an APN recognizing failure or an incorrect APN.
In recycling mode, the device will disable the cellular and GNSS modules, which
means it will neither 󽗉x positions nor upload location data.
APN Setting (If no network is available, you are advised to set the
APN via the mobile app – JIMI IoT LAB)
Working Modes
Recycling mode (Mode1)

In standby mode, the device uploads a position 󽗉x every 24 hours by default. You
can change the interval and time point of upload via a command delivered by the
platform or via the Jimi IoT LAB mobile app.
Set command:
MODE,2,Time,Interval#
Time: 00:01 to 23:59 (default: 07:00)
Interval: 60 to 1440 (default: 1440 minutes)
Standby mode (Mode2)
In tracking mode, the device uploads a position 󽗉x every minute. You can change the
upload and positioning duration via a command delivered by the platform or via the
Jimi IoT LAB mobile app.
Set command:
MODE,3,interval,Working Time#
Interval: 60 to 360 (unit: seconds; default: 60 seconds)
Working Time: 0 to 1440 (unit: minutes; default: 10 minutes)
Note: If the working time is set to "0", the device will not exist tracking mode.
Tracking mode (Mode3)
Switch by command:
MODE[,A]#
A: 1 for recycling mode, 2 for standby mode, 3 for tracking mode
Query current working mode:
MODE#
Switch by key press:
・If the device is in recycling mode, press the function button ⑤ for 5 seconds to
switch to standby mode;
・If the device is in standby mode, short press the function button ⑤ for 3 times in 5
seconds to switch to recycling mode.
Switching Modes

Troubleshootintg
When a problem arises, you can troubleshoot it by the following solution. If the
problem persists, please don't hesitate to contact your dealer or service provider.

Warranty Instructions
① No prior notice will be given if the product is upgraded due to technological reasons.
② The appearance or color of the product is subject to the actual.
③ The warranty card applies to the services of repair, replacement, and refund of the
product with the following IMEI.
④ Please keep this warranty card and the original purchase receipt together in a safe
place, as these will be needed at time of services.
For damages not caused by human factors, this warranty lasts for 2 (two) years
(including one-year replacement service) from the date of the original purchase.
You can choose to pay for the repair services in any of the following cases:
① The warranty card expires;
② No warranty card or valid proof of purchase;
③ The product, including its accessories, is not in the warranty period;
④ Damage caused by unauthorized repairs, crash, liquid spillage, incident, accident,
modi󽗉cations, or incorrect voltage input; or the label, IMEI, or counterfeit mark of the
product is broken or scribbled;
⑤ Damages caused by installation or use not in accordance with the user manual;
⑥ Damage caused by force majeure such as 󽗉re, 󽗊ood, or lightning;
⑦ The device model is inconsistent with the warranty card or the warranty card has
been altered;
⑧ Other damages caused by force majeure.
Special Statement
Warranty Terms

FCC warning
Any Changes or modi󽗉cations not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o󽗈 and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit di󽗈erent from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment complies with RF radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.