John crane 5610vq Guide

5. If the pumped fluid is hazardous or toxic, appropriate precautions

must be taken to ensure that any seal leakage is adequately

contained. Further information on sealing hazardous or toxic fluids

should be obtained from John Crane prior to seal installation.

6. Fluorocarbon components should never be burned or incinerated

as the fumes and residues are highly toxic. If fluorocarbons are

accidentally heated above 400˚C/750˚F, they can decompose.

Protective gloves should be worn as hydrofluoric acid may be present.

7. PTFE components should never be burned or incinerated as the

fumes are highly toxic.

These instructions are for the installation and operation of

a seal as used in rotating equipment and will help to avoid

danger and increase reliability. The information required

may change with other types of equipment or installation

arrangements. These instructions must be read in

conjunction with the instruction manuals for both the

pump and any ancillary equipment.

If the seal is to be used for an application other than that originally

intended or outside the recommended performance limits, John Crane

must be contacted before its installation and use.

Any warranty may be affected by improper handling, installation, or use

of this seal. Contact John Crane for information as to exclusive product

warranty and limitations of liability.

If questions or problems arise, contact your local John Crane representative.

or the original equipment manufacturer, as appropriate.

John Crane mechanical seals are precision products and

must be handled appropriately. Take particular care to

avoid damage to lapped sealing faces and to flexible

sealing rings. Do not excessively compress the seal

before or during installation.

Safety Instructions

1. The following designations are used in the installation instructions to

highlight instructions of particular importance.

NOTE: Refers to special information on how to install or

operate the seal most efficiently.

Refers to special information or instructions directed

towards the prevention of damage to the seal or its

surroundings.

Refers to mandatory instructions designed to

prevent personal injury or extensive damage to the

seal or its surroundings.

2. Installation, removal, and maintenance of the seal must be carried out

only by qualified personnel who have read and understood these

installation instructions.

3. The seal is designed exclusively for sealing rotating shafts. The

manufacturer cannot be held liable for use of the seal for purposes

other than this.

. The seal must only be used in technically perfect condition, and

must be operated within the recommended performance limits in

accordance with its designated use set out in these installation

instructions.

Dry running — often indicated by a squealing noise from

the seal area — will cause overheating and scoring or

other damage to the sealing surfaces, resulting in

excessive leakage or a much shortened seal life.

Before startup, ensure that all personnel and

assembly equipment have been moved to a safe

distance so there is no contact with rotating parts

on the pump, seal, coupling, or motor.

WARNING: Seal installation should be handled only by qualified

personnel. If questions arise, contact the local

John Crane representative. Improper use and/or

installation of this product could result in injury to

the person and/or harmful emissions to

the environment, and may affect any warranty

on the product. Please contact the company for

information as to exclusive product warranty

and limitations of liability.

Before Starting the Equipment

1. Check the pump at the coupling for proper alignment of the driver

or motor.

2. Ensure that the gland plate nuts/bolts are securely tightened

according to the pump manual instructions, and that all screws

are securely fastened.

3. Complete the assembly of the pump, and turn the shaft (by hand if

possible) to ensure free rotation.

. Consult all available equipment operating instructions to check for

correctness of all piping and connections, particularly regarding seal

recirculation/flush, heating or cooling requirements, and services

external to the seal.

This mechanical seal is designed to operate in a liquid

so the heat energy it creates is adequately removed.

Therefore, the following check should be carried out

not only after seal installation, but also after any

period of equipment inactivity.

5. Check that the seal chamber fluid lines are open and free of any

obstruction, and ensure that the seal chamber is properly vented

and filled with liquid — refer to the pump instruction manual.

ATTENTION

TYPE 5610V/5610VQ

SINGLE O-RING CARTRIDGE SEAL

Installation, Operation & Maintenance Instructions

PAGE 1

Foreword

These instructions are provided to familiarize the user with the seal and its

designated use. The instructions must be read and applied whenever work

is done on the seal, and must be kept available for future reference.

General Instructions

1. Study the engineering layout drawing to confirm the proper seal

arrangement for the pump being used. Types 5610V and 5610VQ seals

are designed for versatility and can be assembled in various ways.

The following instructions describe the standard configurations.

2. To assure satisfactory operation, handle the seal with care. Take

particular caution to see that the lapped sealing faces are not

scratched or damaged.

Preparing the Equipment

1. Check seal chamber dimensions and finishes:

2. Measure axial end play: Sizes to 3.000" 0.003" FIM max.

3.000" and greater 0.005" FIM

max.

3. Determine squareness of seal chamber face to shaft:

Rotating Mating Ring

Sizes to 3.000" 0.005" FIM max.

3.000" and greater 0.007" FIM max.

Rotating Seal Head

Sizes to 3.000" 0.002" FIM max.

3.000" and greater 0.003" FIM max.

. Measure shaft runout:

Sizes to 3.000" 0.002" FIM max.

3.000" and greater 0.003" FIM

SHAFT OR SLEEVE

0.040 LG. X 20˚ CHAM.

BORE

0D +0.000"

-0.002"

0.040"

20˚

MOVE SHAFT IN AXIAL DIRECTION

BY HAND. NOTE MEASUREMENT

ON DIAL INDICATOR

MOUNT

DIAL INDICATOR

ON SHAFT

TURN SHAFT BY HAND AND NOTE

MEASUREMENT ON DIAL INDICATOR

MOUNT

DIAL INDICATOR

ON SHAFT

TURN SHAFT BY HAND AND NOTE

MEASUREMENT ON DIAL INDICATOR

MOUNT

DIAL INDICATOR

ON SEAL CHAMBER

FACE

Assemble the Type 5610V as follows, referring to the applicable

engineering layout drawing.

NOTE: These instructions apply to a rotating mating ring configuration.

The seal assembly and mating ring positions could be reversed

should an application require.

NOTE: Elastomeric O-rings can be damaged or destroyed if care is not

taken. Prior to assembly of O-ring into groove, make sure groove

is clean and free of foreign materials. Lubricate both groove and

O-ring prior to installation with light lube oil (SAE #10 or #20) or

silicone grease (such as Dow Corning compound #4). For ethylene

propylene elastomers, do not lubricate with petroleum products.

1. Place gland plate on table with gasket side facing up.

2. Install lubricated O-ring into outside diameter (OD) groove of mating

ring.

3. Stand sleeve on its base and slide mating ring over sleeve, align pins,

and press in place.

. Install set screws in collar.

5. Loosely attach the spacers to the collar with cap screws.

6. Set the gland plate assembly gasket side down on table. Install

collar on gland plate assembly and engage spacers into groove,

aligning spacers with pipe taps of gland plate. Uniformly finger

tighten the cap screws.

7. Install lubricated O-ring into OD groove of retainer.

8. Place spring inside retainer.

9. Insert O-ring in retainer, ensuring that the O-ring is past the drive

slots.

10. Align ears on primary ring with slots on the retainer and press into

bore of retainer. Make sure primary ring is engaged into slots and

moves freely.

11. Place gland plate onto table with gasket side up.

12. Insert seal assembly in gland plate, align pins, and press in place.

Turn gland plate over and confirm that retainer is flush with end of

gland plate.

13. Clean faces of primary and mating rings with denatured alcohol

and a lint-free cloth.

1 . Making sure seal face does not fall out, slide gland plate sub-

assembly over sleeve until faces touch.

Part Name

1 Mating Ring 7 Collar 13 Gasket

2 O-ring 8 Set Screws 14 Snap Ring

3 Primary Ring 9 Spacers 15 O-ring

4 O-ring 10 Cap Screws

5 Sleeve Assembly 11 Gland Plate Assembly

6 O-ring 12 Spring

Type 5610V Single O-ring Cartridge Seal Assembly

NOTE: If measured dimensions exceed those values given, correct the equipment to meet specifications prior to seal installation.

Typical Type 5610V Single O-Ring Cartridge

Seal Arrangement

5 43 12 8

6 2

TYPE 5610V/5610VQ

SINGLE O-RING CARTRIDGE SEAL

Installation, Operation & Maintenance Instructions

PAGE 2

SLOT

WIDTH



Type 5610V Single Cartridge Dimensional Data (inches)

Seal D4

Size/D1 D2 Min. Ma . D26 L12 L23 L39 L56 L90 L91 L92 M N

1.000 1.375 1.445 1.889 4.000 1.989 1.353 1.954 0.531 2.000 0.160 0.035 0.525 2.805

1.125 1.500 N/A 2.015 4.125 2.062 1.446 2.062 0.531 2.125 0.125 N/A 0.525 2.933

1.250 1.625 N/A 2.294 4.250 2.062 1.446 2.062 0.531 2.125 0.125 N/A 0.525 3.213

1.375 1.750 N/A 2.421 4.375 2.062 1.446 2.062 0.531 2.125 0.125 N/A 0.525 3.338

1.500 1.937 2.007 2.680 4.875 2.156 1.487 2.125 0.593 2.187 0.156 0.031 0.525 3.599

1.625 2.062 2.132 2.812 5.000 2.156 1.487 2.125 0.593 2.187 0.156 0.031 0.562 3.766

1.750 2.170 2.240 2.918 5.250 2.156 1.487 2.125 0.593 2.187 0.156 0.031 0.562 3.875

1.875 2.312 2.382 2.918 5.250 2.156 1.487 2.125 0.593 2.187 0.156 0.031 0.562 3.875

2.000 2.437 2.507 3.015 5.500 2.375 1.601 2.312 1.063 2.375 0.187 0.062 0.562 4.000

2.125 2.562 2.632 3.360 5.859 2.375 1.601 2.312 1.593 2.375 0.187 0.062 0.687 4.469

2.250 2.687 2.757 3.485 6.500 2.375 1.601 2.312 0.593 2.375 0.187 0.062 0.687 4.566

2.375 2.812 2.882 3.610 6.500 2.484 1.717 2.466 0.625 2.528 0.143 0.018 0.687 4.719

2.500 3.062 N/A 3.891 6.750 2.484 1.717 2.562 0.625 2.625 0.125 N/A 0.687 5.000

2.625 3.312 N/A 4.062 6.750 2.500 1.625 2.500 0.625 2.562 0.125 N/A 0.687 5.170

2.750 3.312 N/A 4.062 6.750 2.500 1.625 2.500 0.625 2.562 0.125 N/A 0.687 5.170

2.875 3.375 N/A 4.186 7.000 2.500 1.725 2.500 0.625 2.562 0.125 N/A 0.687 5.312

3.000 3.625 N/A 4.469 7.750 2.500 1.787 2.562 0.685 2.625 0.125 N/A 0.812 5.720

3.125 3.750 3.853 4.600 7.875 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.812 5.845

3.250 3.750 3.853 4.600 7.437 2.562 1.593 2.510 N/A 2.635 0.177 0.052 0.812 5.845

3.375 4.000 4.125 4.850 8.125 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.812 6.095

3.500 4.125 4.250 4.975 8.250 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.812 6.220

3.625 4.218 4.343 5.100 8.375 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.687 6.250

3.750 4.343 4.468 5.199 8.750 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.687 6.770

3.875 4.468 4.593 5.375 8.750 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.812 6.636

4.000 4.593 4.718 5.500 9.000 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.812 6.761

4.125 4.718 4.843 5.625 9.000 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.812 6.886

4.250 4.843 4.968 5.750 9.250 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.812 7.011

4.500 5.093 5.218 6.000 9.500 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.812 7.261

4.750 5.343 5.468 6.313 10.375 2.562 1.593 2.562 N/A 2.687 0.125 N/A 0.812 7.574

5.000 5.843 5.968 7.260 12.000 2.953 1.749 3.043 N/A 3.168 0.125 N/A 0.812 10.000

5.250 6.093 6.218 7.510 12.250 2.953 1.749 3.043 N/A 3.168 0.125 N/A 0.812 10.250

5.500 6.343 6.468 8.000 12.687 2.953 1.749 3.043 N/A 3.168 0.125 N/A 0.937 10.500

Type 5610VQ Single Cartridge Dimensional Data (inches)

Seal D4

Size/D1 D3 Min. Ma . D26 L12 L23 L39 L56 L90 L91 L92 M N

1.000 1.564 1.625 1.889 4.000 2.575 1.353 1.954 0.531 2.000 0.746 0.621 0.525 2.805

1.125 1.689 1.750 2.015 4.125 2.651 1.446 2.062 0.531 2.125 0.714 0.589 0.525 2.933

1.250 1.812 1.875 2.294 4.250 2.728 1.446 2.062 0.531 2.125 0.791 0.666 0.525 3.213

1.375 1.939 2.000 2.421 4.375 2.728 1.446 2.062 0.531 2.125 0.791 0.666 0.525 3.338

1.500 2.187 2.250 2.680 4.875 2.744 1.487 2.125 0.593 2.187 0.744 0.619 0.525 3.599

1.625 2.312 2.375 2.812 5.000 2.744 1.487 2.125 0.593 2.187 0.744 0.619 0.562 3.766

1.750 2.406 2.480 2.918 5.250 2.744 1.487 2.125 0.593 2.187 0.744 0.619 0.563 3.875

1.875 2.549 2.625 2.918 5.250 2.744 1.487 2.125 0.593 2.187 0.744 0.619 0.563 3.875

2.000 2.673 2.750 3.015 5.500 2.963 1.601 2.312 1.032 2.375 0.775 0.650 0.562 4.000

2.125 2.798 2.875 3.360 5.859 2.963 1.601 2.313 0.593 2.375 0.775 0.650 0.687 4.469

2.250 2.923 3.000 3.485 6.500 2.963 1.601 2.313 0.593 2.375 0.775 0.650 0.687 4.566

2.375 3.048 3.125 3.610 6.500 3.063 1.717 2.466 0.625 2.528 0.722 0.597 0.687 4.719

2.500 3.301 3.375 3.891 6.750 2.980 1.717 2.563 0.625 2.625 0.542 0.417 0.687 5.000

2.625 3.551 3.625 4.062 6.750 3.088 1.625 2.500 0.625 2.562 0.713 0.588 0.687 5.170

2.750 3.551 3.625 4.062 6.750 3.088 1.625 2.500 0.625 2.562 0.713 0.588 0.687 5.170

2.875 3.614 3.687 4.186 7.000 3.088 1.725 2.500 0.625 2.562 0.713 0.588 0.687 5.312

3.000 3.864 3.934 4.469 7.750 3.088 1.787 2.562 0.685 2.625 0.651 0.526 0.812 5.720

3.125 4.022 4.125 4.600 7.875 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.812 5.845

3.250 4.022 4.125 4.600 7.437 3.093 1.593 2.510 N/A 2.635 0.708 0.583 0.812 5.845

3.375 4.246 4.375 4.850 8.125 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.812 6.095

3.500 4.371 4.500 4.975 8.250 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.812 6.220

3.625 4.500 4.625 5.100 8.375 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.687 6.250

3.750 4.625 4.724 5.199 8.750 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.687 6.770

3.875 4.750 4.875 5.375 8.750 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.812 6.636

4.000 4.875 5.000 5.500 9.000 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.812 6.761

4.125 5.000 5.125 5.625 9.000 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.812 6.886

4.250 5.125 5.250 5.750 9.250 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.812 7.011

4.500 5.375 5.500 6.000 9.500 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.812 7.261

4.750 5.625 5.750 6.313 10.375 3.156 1.593 2.562 N/A 2.687 0.719 0.594 0.812 7.574

5.000 6.125 6.250 7.260 12.000 3.609 1.749 3.043 N/A 3.168 0.691 0.566 0.812 10.000

5.250 6.375 6.500 7.510 12.250 3.609 1.749 3.043 N/A 3.168 0.691 0.566 0.812 10.250

5.500 6.625 6.750 8.000 12.687 3.609 1.749 3.043 N/A 3.168 0.691 0.566 0.937 10.500

15. Carefully rotate the gland plate until through holes in sleeve are lined

up with the collar set screws.

16. Carefully press down on gland plate and install snap ring over the end

of sleeve. This sets the axial spacing of the cartridge. Do not over-

compress gland plate or this may damage the seal.

17. Tighten set screws until they start to enter the sleeve ID.

18. Uniformly tighten cap screws on spacers.

19. Install gasket and sleeve O-ring. Apply a small amount of compatible

adhesive to gasket to hold it in place.

20. Pressure test according to John Crane standard QA-5-0568.

21. Plug pipe taps with plastic plugs.

Type 5610V Single O-ring Cartridge Seal Assembly (continued)

Typical Type 5610VQ Installation Dimensions

Typical Type 5610V Installation Dimensions

*MIN. TURN DIAM.

L12

L23

L39L91 MIN.

BOX DEPTH

L92

L90 MIN. NEAREST OBSTRUCTION

D26

L56

L12

L23

L39L91 MIN.

BOX DEPTH

L92

L90 MIN. NEAREST OBSTRUCTION

D26

L56

*MIN. TURN DIAM.

TYPE 5610V/5610VQ

SINGLE O-RING CARTRIDGE SEAL

Installation, Operation & Maintenance Instructions

PAGE 3

Installing the Seal

1. Before starting the installation, read the following instructions carefully.

2. Remove the seal from its packaging, inspect for any damage and wipe

clean.

3. The equipment should be clean and meet the specifications noted in

the “Preparing the Equipment” section. Lubricate sleeve O-ring with

lubricant recommended in chart below. Lubricate shaft sparingly.

Lubricate gland plate bolts/nuts as required.

Type 5610V Oversize Bore Single Cartridge

Dimensional Data (inches)

Seal D4 Min.

Size/D1 D2 Min. Ma . D26 L12 L23 L39 L56 L90 L91 L92 M N Turn Diam.

1.375 1.750 2.875 3.023 5.375 2.062 1.446 2.062 0.625 2.125 0.250 0.125 0.562 4.062 3.268

1.750 2.170 3.500 3.925 6.500 2.156 1.487 2.125 0.656 2.187 0.250 0.125 0.687 5.093 3.885

1.875 2.312 3.625 3.734 6.500 2.156 1.316 1.954 0.485 2.017 0.327 0.202 0.687 5.093 *

2.125 2.562 3.875 4.250 7.250 2.375 1.570 2.282 0.749 2.407 0.219 0.094 0.687 5.687 4.264

2.500 3.062 4.750 5.078 8.000 2.484 1.697 2.407 0.749 2.625 0.204 0.079 0.687 6.062 5.139

2.625 3.312 4.625 4.740 8.000 2.500 1.619 2.329 0.578 2.454 0.296 0.171 0.687 6.062 **

2.750 3.312 4.750 4.875 8.000 2.500 1.697 2.407 0.656 2.532 0.218 0.093 0.687 6.062 5.139

*Seal cartridge is OD registered on the Turn Diam. of 4.125".

**Seal cartridge is OD registered on the Turn Diam. of 5.125".

ELASTO ER LUBRICANT

Fluoroelastomer Vegetable Oil, Animal Oil, ineral-Hydrocarbon Oils,

(i.e., Viton®) Soap Solution, Parker ‘Super-O-Lube,’ Silicone Grease

Ethylene Propylene Vegetable Oil, Polywater®, Soap Solution, Glycerine,

Propylene Glycol, Silicone Grease

Perfluoroelastomer Vegetable Oil, Animal Oil, ineral-Hydrocarbon Oils

(i.e., Kalrez®)

NOTE: Always use a lubricant that is compatible with your machinery and product.

Use lubricant sparingly, only enough to install seal with ease.

Viton and Kalrez are registered trademarks of DuPont.

Polywater is a registered trademark of American Polyware Co.

GLAND BOLTS

SPACERS

CAP SCREWS

Type 5610VQ Oversize Bore Single Cartridge

Dimensional Data (inches)

Seal D4 Min.

Size/D1 D3 Min. Ma . D26 L12 L23 L39 L56 L90 L91 L92 M N Turn Diam.

1.375 1.939 2.875 3.023 5.375 2.062 1.446 2.062 0.625 2.125 0.791 0.666 0.562 4.062 3.268

1.750 2.406 3.500 3.925 6.500 2.156 1.487 2.125 0.656 2.187 0.744 0.619 0.687 5.093 3.885

1.875 2.549 3.625 3.734 6.500 2.156 1.316 1.954 0.485 2.017 0.915 0.790 0.687 5.093 *

2.125 2.798 3.875 4.250 7.156 2.375 1.570 2.282 0.749 2.407 0.806 0.681 0.687 5.687 4.264

2.500 3.301 4.750 5.078 8.000 2.484 1.697 2.407 0.656 2.532 0.698 0.573 0.687 6.062 5.000

2.625 3.551 4.625 4.740 8.000 3.088 1.619 2.329 0.578 2.454 0.884 0.759 0.687 6.062 **

2.750 3.551 4.750 4.875 8.000 2.500 1.697 2.407 0.656 2.532 0.806 0.681 0.687 6.062 5.139

*Seal cartridge is OD registered on the Turn Diam. of 4.125".

**Seal cartridge is OD registered on the Turn Diam. of 5.125".

. Make sure that gland plate gasket is properly positioned, and that

collar set screws do not extend past sleeve ID. Slide complete

cartridge seal assembly onto shaft. For ANSI pumps, position gland

plate so pipe connection #1 is at or near top dead center. For DIN

pumps, position gland plate so slot between pipe connections #2

and #3 is at or near top dead center. Slide cartridge onto studs (if

applicable) until gasket is flush against the face of seal chamber.

Hand tighten gland plate bolts/nuts.

5. Reassemble pump and make all necessary impeller adjustments.

6. Continue tightening gland plate bolts/nuts in an alternating pattern

until secure (1/4 turns, 180˚ apart), with gland plate and face of

pump seal chamber metal to metal. Do not over-stress or distort

gland plate.

7. Tighten collar set screws evenly (1/4 turns, 180˚ apart), securing

cartridge seal to shaft.

8. Remove spacers and save.

9. Make appropriate piping connections to seal assembly.

SET SCREWS

O-RING

TYPE 5610V/5610VQ

SINGLE O-RING CARTRIDGE SEAL

Installation, Operation & Maintenance Instructions

PAGE 4

Installing the Seal (continued)

It is recommended that the seal cavity be vented through the pump’s lantern

ring connection located at top dead center. It is always recommended that a

flush injection be utilized. The flush should be piped into the seal gland to

ensure maximum efficiency.

For DIN pumps rotate gland 135˚ CCW. Use port #2 as flush.

NOTE: For CCW (counter clockwise) rotation pumps,

consult John Crane engineering.

Clockwise

Rotation

Drain “D”

Type 5610V

Port #1 - Not Drilled

Port #2 - Flush

Port #3 - Not Drilled

Port #4 - Not Drilled

Flush “F”

Quench “Q”

Clockwise

Rotation

Port #1 - Quench

Port #2 - Flush

Port #3 - Drain

Port #4 - Not Drilled

Type 5610VQ

Flush “F”

Decommissioning the Equipment

1. Ensure that the equipment is electrically isolated.

If the equipment has been used on toxic or ha ardous

fluids, ensure that the equipment is correctly decontami-

nated and made safe prior to commencing work.

Remember, fluid is often trapped during draining and

may exist outside the seal. The equipment instruction

manual should be consulted to check for any special pre-

cautions.

2. Ensure that the equipment is isolated by the appropriate valves.

Check that the fluid is drained and pressure is fully released.

Maintenance

No maintenance of a seal is possible while installed. Therefore, it is

recommended that a spare seal unit be held in stock to allow immediate

replacement of a removed seal.

It is recommended that used seals are returned to a John Crane service

location, as rebuilding to as-new specifications must be carried out by

qualified personnel.

It is the responsibility of the equipment user to ensure that any

parts being sent to a third party have appropriate safe

handling instructions externally attached to the package.

Quality Assurance

This seal has been assembled in accordance with John Crane quality

assurance standards and with proper maintenance and use will give safe

and reliable operation to the maximum recommended performance as

shown in any relevant approved John Crane publication.

TYPE 5610V/5610VQ

SINGLE O-RING CARTRIDGE SEAL

Installation, Operation & Maintenance Instructions

PAGE 5

Ordering Information

1. Cartridge seal size solid shaft or sleeve outside diameter (OD).

2. Select single (5610V) or single with quench (5610VQ) arrangement.

3. Determine whether standard or enlarged seal chamber configuration

is required.

. Choose seal drawing number from chart below.

5. For other material combinations or size considerations, consult your

local John Crane representative.

Materials of Construction - Standard

Primary Ring Carbon Graphite

Silicon Carbide (optional)

Nickel Binder Tungsten Carbide (optional)

Mating Ring Silicon Carbide

Nickel Binder Tungsten Carbide (optional)

Cartridge Hardware 316 Stainless Steel*

Secondary Seal Fluoroelastomer*

Operating Limits

Pressure: Sizes up to 3.000" — 21 bar g/300 psig max.

Sizes over 3.000" — 13 bar g/200 psig

Temperature: -29˚C to 204˚C/-20˚F to 400˚F

Speed: To 25 m/s/5,000 fpm

*Various options.

Type 5610V/5610VQ Cartridge Drawing Numbers

Standard Bore Layouts

Seal Size 5610V 5610VQ

1.000 H-SP-1030362 H-SP-1030394

1.125 H-SP-1030363 H-SP-1030395

1.250 H-SP-1030364 H-SP-1030396

1.375 H-SP-1030365 H-SP-1030397

1.500 H-SP-1030366 H-SP-1030398

1.625 H-SP-1030367 H-SP-1030399

1.750 H-SP-1030368 H-SP-1030400

1.875 H-SP-1030369 H-SP-1030401

2.000 H-SP-1030370 H-SP-1030402

2.125 H-SP-1030371 H-SP-1030403

2.250 H-SP-1030371 H-SP-1030404

2.375 H-SP-1030373 H-SP-1030405

2.500 H-SP-1030374 H-SP-1030406

2.625 H-SP-1030375 H-SP-1030407

2.750 H-SP-1030376 H-SP-1030408

2.875 H-SP-1030377 H-SP-1030409

3.000 H-SP-1030378 H-SP-1030410

3.125 H-SP-1030379 H-SP-1030411

3.250 H-SP-1030380 H-SP-1030412

3.375 H-SP-1030381 H-SP-1030413

3.500 H-SP-1030382 H-SP-1030414

3.625 H-SP-1030383 H-SP-1030415

3.750 H-SP-1030384 H-SP-1030416

3.875 H-SP-1030385 H-SP-1030417

4.000 H-SP-1030386 H-SP-1030418

4.125 H-SP-1030387 H-SP-1030419

4.250 H-SP-1030388 H-SP-1030420

4.500 H-SP-1030389 H-SP-1030421

4.750 H-SP-1030390 H-SP-1030422

5.000 H-SP-1030391 H-SP-1030423

5.250 H-SP-1030392 H-SP-1030424

5.500 H-SP-1030393 H-SP-1030425

Type 5610V/5610VQ Cartridge Drawing

Numbers

Oversize Bore Layouts

Seal Size 5610V 5610VQ

1.375 H-SP-1032553 H-SP-1032554

1.750 H-SP-1032556 H-SP-1032557

1.875 H-SP-1032559 H-SP-1032560

2.125 H-SP-1032562 H-SP-1032563

2.500 H-SP-1032565 H-SP-1032566

2.625 H-SP-1032568 H-SP-1032569

2.750 H-SP-1032571 H-SP-1032572

TYPE 5610V/5610VQ

SINGLE O-RING CARTRIDGE SEAL

Installation, Operation & Maintenance Instructions

PAGE 6

TYPE 5610V/5610VQ

SINGLE O-RING CARTRIDGE SEAL

Installation, Operation & Maintenance Instructions

PAGE 7

TYPE 5610V/5610VQ

SINGLE O-RING CARTRIDGE SEAL

Installation, Operation & Maintenance Instructions

PAGE 8

If the products featured will be used in a potentially dangerous and/or hazardous process, your John Crane representative should be consulted prior to

their selection and use. In the interest of continuous development, John Crane Companies reserve the right to alter designs and specifications without

prior notice. It is dangerous to smoke while handling products made from PTFE. Old and new PTFE products must not be incinerated. ISO 9001 and

ISO14001 Certified, details available on request.

North Amer ca

nited States of America

Tel: 1-847-967-2400

Fax: 1-847-967-3915

Europe

nited Kingdom

Tel: 44-1753-224000

Fax: 44-1753-224224

Lat n Amer ca

Brazil