John Lewis Charlotte Bed 80371707 User manual

1/6
Charlotte Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
Double
John Lewis
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Thank you for purchasing this Charlotte Bed. Please read the instructions carefully before use to ensure
safe and satisfactory operation of this product.
Not included in hardware list

2/6
A
B
C
D
E
F
G
H
I
J
M5 Allen Key x 1
M4 Allen Key x 1
Side Caps x 14
Centre Caps x 7
M6 X 25mm Bolt x 10
M8 Spring Washer x 4
1
2
3
4
5
6
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 14
Centre Rail x 1
Legs x 4
Parts
Fittings
M13 Spanner x 1
7
Metal Plates x 4
M8 Nut x 4
Screw 3.5 X 30mm x 4
Wide Centre Caps x 8
Wide Side Caps x 16
8
K
Wide Slats x 16
Fittings and parts checklist

3/6
1
3
3
2
Hook the pre-attached metal fixings on the Side Rails (3) over the pre-inserted bolts in the Headboard (1)
and Footboard (2) and hand-tighten to loosely secure parts together. Do not tighten with M5 Allen Key (B)
until you have inserted the Centre Rail in the next step.
Step by step assembly instructions
Step One
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
NEXT STEP
Step Two
BRACKET
SIDE RAIL
3
1
2
AND
Bracket
Side Rail
1
2
3
AND
M5 Allen Key
x 1
M4 Allen Key
x 1
M6 x 25mm x 2
Centre Rail
(6)
S
T
E
P
1
M4 (A)
M6 x 25mm (G)
S
T
E
P
2
G. A.
Insert Centre Rail (6) into the brackets in the centre of the Headboard (1) and Footboard (2).
Push down fully and secure in place using M6 x 25mm bolt (G) and tighten with M4 Allen Key (A). You can
now tighten the bolts at the Side Rails from previous step (Step One) with M5 Allen Key (B) so all fastenings
are now tightened.
B.
1
S
T
E
P
3
Bracket
Side Rail
3
M5
6
AFTER INSERTING CENTRE RAIL,
TIGHTEN ALL FIXINGS FULLY
INCLUDING BOLTS AT SIDE RAILS
(FROM STEP ONE)

4/6
Step Three
Step Four
For Footboard
Next attach the legs to the Headend (1) Footend (2) as shown in diagram using Bolt M6x25mm (G) and
Screw 3.5x30mm (J). Tighten the bolts with Allen Key M4 (A).
Attach Metal Plate (8) and Leg (7) together as shown in Step 1. Attach together Leg (7) and Metal Plate (8) using
M8 Spring Washer (H) and M8 Nut (I) then tighten with M13 Spanner (K).
2
3
8
3.5 x30mm (J)
M6 X 25mm (G)
M6 X 25mm (G)
M4(A)
2
1
8
3.5 x30mm(J)
M6 X 25mm (G)
M6 X 25mm (G)
M4(A)
M4(A)
x2
F
o
r
H
e
a
d
b
o
a
r
d
M6 X 25mm (G)
7
7
7
3
8
3.5 x30mm (J)
G. J.
M6 X 25mm x 8
1.
M4 Allen Key x 1 3.5 x 30mm x 4
STEP 2
M8 Nut (I)
M13 Spanner (K)
M8 Spring Washer (H)
6
7
STEP 1
x4
7
6
STEP 2
7
8
STEP 1
x4
8
7
I.
K.
M8 Nut x 4
M13 Spanner
x 1
Legs x 4
8.
Metal plate x 4
H.
M8 Spring
Washer x 4
7.
NOT INCLUDED
3

5/6
Step Six
This bed is now ready to use.
2 Lines
Normal slats
1 Line
Normal slat
2 Lines
Wide slats
2 Lines
Wide slats
2 Lines
Normal slats
2 Lines
Normal slats
4 Lines
Wide slats
ZONE 2
ZONE 1
ZONE 5
ZONE 7
ZONE 6
ZONE 4
ZONE 3
Diagram 1
D
F
4
5
(x8)
(x7)
4.
5.
C.
D
F.
E.
Side Caps x 14
.
Wide Centre Caps
x 8
Wide Side Caps
x 16
Wide Slats x 16
Slats x 14
Step Five
With the curved side facing upwards, insert 2 slats into a centre cap then into 2 side caps on either
end(x15). (Please note the Wide Slats (5) must be inserted with the Wide Centre Caps (E) and Wide
Side Caps (F)). Repeat this process for all slats.
Note: Please see the Diagram 1 below to arrange the slat with the correct system).
4
4
C
E
5
5
Centre Caps x 7
E
F
F
D
D
4
4
5
5
C