John Lewis Simba Hybrid 80355515 Operating instructions

PRE-ASSEMBLY PREPARATION
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembl
Do not use power tools to assemble.
y.
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
1/6
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact customer services on 01244 689949 or email
[email protected].

Fitting and Parts checklist
A
B
C
E
D
M5 Allen Key X 1
M4 Allen Key X 1 Side Plastic Caps x 30
Centre Plastic Caps x 15
M6 X 25mm Bolt x 2
1
2
3
4
5
6
7
Headboard x 1
Footboard x 1
Side Rails x 2
60mm Slats x 20
80mm Slats x 10
Centre Rail x 1
Legs x 4
2/6

3
3
2
1
Step Two
Step by step assembly instructions
Step One
Legs x 4
2
1
2
3
BRACKET
SIDE RAIL
Hook the pre-attached brackets on the Side Rails (3) over the pre-inserted bolts in the head and footboard and
hand-tighten bolts to loosely secure parts together. Do not tighten with the M5 Allen Key (B) until you have
inserted the Centre Rail in Step Three.
Place Wooden Legs (6) into the holes in the underside of the Headboard (1) and Footboard (2) as per
diagram below and twist into place so they are fully secured.
Head/Foot
Board
Pre-inserted Nut
Wooden Leg
BRACKET
SIDE RAIL
3
1
7
7
7
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
STEP THREE
3/6
7.
7
7

1
6
3
3
22
1
2
Step Three
Step Four
M4 Allen Key (A)
M6 x 25mm (E)
M4 Allen Key x 1 M6 x 25mm Bolt x 2
A. E.
AFTER INSERTING CENTRE
RAIL, TIGHTEN ALL FIXINGS
FULLY INCLUDING BOLTS
AT SIDE RAILS (FROM
STEP TWO)
Insert Centre Rail (6) into the brackets in the centre of the Headboard (1) and Footboard (2). Push down
fully and secure in place using M6 x 25mm Bolts (E). Tighten bolts with M4 Allen Key (A). You can now
tighten the bolts at the Side Rails from previous step (Step Two) so all fastenings are now tightened.
S
T
E
P
1
S
T
E
P
2
Side Plastic Caps x 30
Centre Plastic Caps x 15
60mm Slats x 20
5.
4.
C.
D.
D
4
x30
4
4
C
D
D
4
4
x15
C
4/6
With the curved side facing upwards, insert 2 Slats into a Centre Cap (C) followed by a Side Cap (D)
onto the other end of both slats. By placing the slat alternately 5 rows 60mm Slats (4) and 5 rows 80mm
Slats (5), use your palms to push down the centre caps into the centre rail and side caps to the side rails
as shown in diagram below.
80mm Slats x 10
CAUTION
Please ensure that the bigger size of slat placed in the middle of the rail.
This will ensure the best support to hold the load.
{ 5 rows 60mm Slat }
{ 5 rows 60mm Slat } { 5 rows 80mm Slat }

Step Five
The bed is now ready for use.
5/6

Care and Maintenance
Safety Instructions
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent
adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
This bed should be cleaned using a soft damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration
process.
Bolts holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.
6/6