John Lewis Giorgio Bed User manual

Giorgio Bed
MTO
Thank you for purchasing this Giorgio bed. Please read the instructions carefully before use to ensure safe
and satisfactory operation of this product.
King
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact customer services on 01244 689949 or email
[email protected].
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembl
Do not use power tools to assemble.
y.
1/7
1

Side Caps x 16
Legs x 4
2/7
A
B
C
D
E
F
G
H
I
J
K
L
M5 Allen Key x 1
M4 Allen Key x 1
Wide Side Caps x 16
Centre Caps x 8
Wide Centre Caps x 8
M6 X 25mm Bolt x 2
M6 Spring Washer x 8
M8 Spring Washer x 2
M6 Washer x 8
Fitting and parts checklist
1
2
3
4
5
6
7
8
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 16
Wide Slats x 16
Centre Rail x 1
Pillows x 2
Parts
Fittings
M6 X 40mm Bolt x 8
M8 X 45mm Bolt x 2

Place Legs (7) under the Headboard (1), and Footboard (2). Attach the Legs (7) to both Headboard and
Footboard using M6 x 40mm Bolt (J), M6 Spring Washer (G) and M6 Washer (H). On Footboard,
hand-tighten to loosely secure parts together. Do not Tighten with the M4 Allen Key until you have inserted
the leg’s Bolt to the side rail in the next step. (As per diagram below)
Step by step assembly instructions
L.
M8 Spring Washer
x 2
K.
M8 x 45mm Bolt
x 2
Step One
Step Two
3/7
x2
Fig. 2
Fig. 1
x2
1
3
M8x45mm (K)
(L)
LOOSELY SECURE PARTS TOGETHER
IN ORDER FOR CENTRE RAIL
TO FIT IN NEXT STEP
Bracket
Side Rail
1
2
AND
3
Starting with the Headboard (1) attach the Side Rails (3) using the one pre-inserted M8 x 45mm Bolt (K), M8 Spring
Washer (L). Please do not tighten the bolts yet. Now, place Metal Bracket on Side Rails (3) over pre-inserted in the
Footboard (2). Only then can you proceed to insert the M8 x 45mm Bolt (K), M8 Spring Washer (L) in the Other hole
on the Headboard (1). Do not tighten with M5 Allen Key (B) until you have inserted the Centre Rail in the next step.
M6 X 40mm x 6
M6 Spring Washer
x 6 M6 Washer x 6 Legs x 4
H.G. J. 7.
DO NOT TIGHTHEN THE BOLT ON
THE FOOTBOARD UNTIL YOU
HAVE INSERTED THE LEG’S BOLT
AT THE SIDE RAIL
M6 x 40mm (J)
M6 Spring Washer
(G)
M6 Washer (H)
(Footboard)
Bolt inserted
on Outer Hole ONLY
x 2
7
7
2
7
7
1
3
1
2
3
(HEADBOARD)
M4 (A)
M6 x 40mm (J)
M6 Spring Washer
(G)
M6 Washer (H)
x 2
Bolt inserted
on Outer Hole
ONLY
NOTE: Ensure the Side Rail (3) which has sticker saying ‘HEAD’ is attached on headboard side.
HEAD
HEAD

M6 X 40mm x 2
M6 Spring Washer
x 2 M6 Washer x 2 M4 Allen Key x 1
H.G. J. A.
4/7
Step Three
Step Four
M4 Allen Key x 1
Lower the Centre Rail (6) into the brackets in the centre of the Headboard (1) and Footboard (2) as shown in Fig.3.
Now secure the Centre Rail (6) using the M6x25mm Bolts (I) and tighten with the M4 Allen Key (A) as shown
in Fig.4. You can now tighten the bolts in the Side Rails from the previous step (Step two) with the M5 Allen Key (B)
so that all the fastenings are secure.
M5 Allen Key x 1
M6 x 25mm x 2
I. A. B.
Centre Rail
F
i
g
.
3
6
1
2
And
M4(A)
M6 x 25(I)
F
i
g
.
4
6
1
2
And
AFTER INSERTING CENTRE RAIL,
TIGHTEN ALL FIXINGS FULLY
INCLUDING BOLTS AT SIDE RAILS
(FROM STEP TWO)
2
x2
1
3
M8x45mm (K)
(L)
M5(B)
1
2
3
6
(Footboard)
Bolt inserted
on Outer Hole
ONLY
x 2
M6 x 40mm (J)
M6 Spring Washer
(G)
M6 Washer (H) M4 (A)
From the previous step (Step One), continue to hand-tighten the leg onto the Side Rail (3) to loosely secure the
parts together onto the Footboard (2) using the M6 x 40mm Bolt (J), M6 Spring Washer (G) and M6 Washer (H).
Adjust the leg accordingly, and now you can tighten all the bolts including those from the previous step
(Step One) with the Allen Key M4 (A) so all the fastenings are now tightened. (As per diagram below
AFTER INSERTING SIDE RAIL,
TIGHTEN ALL LEG FIXINGS FULLY
INCLUDING BOLTS AT FOOTBOARD
(FROM STEP ONE)
1
2
3
HEAD
HEAD
HEAD

2 Lines
Normal slats
2 Lines
Normal slat
2 Lines
Wide slats
2 Lines
Wide slats
2 Lines
Normal slats
2 Lines
Normal slats
4 Lines
Wide slats
ZONE 2
ZONE 1
ZONE 5
ZONE 7
ZONE 6
ZONE 4
ZONE 3
Diagram 1
1
D
F
4
5
(x8)
(x8)
4.
5.
C.
D
F.
E.
Side Caps x 16
.
Wide Centre Caps
x 8
Wide Side Caps
x 16
Wide Slats x 16
Slats x 16
With the curved side facing upwards, insert 2 slats into a centre cap then into 2 side caps on either
end(x16). (Please note the Wide Slats (5) must be inserted with the Wide Centre Caps (E) and Wide
Side Caps (F)). Repeat this process for all slats.
Note: Please see the Diagram 1 below to arrange the slat with the correct system).
Centre Caps x 8
E
F
F
D
D
4
4
5
5
C
Step Six
5/7
Step Five
Pillows x 2
8.
Rest the pillows (8) onto the headboard (1) until it reaches the wooden shelf on the headboard.
1
8
8
1
4
4
C
E
5
5

6/7
Step Seven
This bed is now ready to use.
1

Care and Maintenance
Safety Instructions
If you require any additional information or have any issues with this product please call the customer
services helpline on 01244 689949 or email [email protected].
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent
adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
This bed should be cleaned using a soft, damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration
process.
Bolts holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.
7/7