John Lewis 803/43703 User manual

Jamie Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use.TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
Stock Code : 803/43703
Single
John Lewis
For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
Thank you for purchasing this Jamie Bed. Please read the instructions carefully before use to ensure safe
and satisfactory operation of this product.
1/6
Not included in hardware list

Fittings and parts checklist
A
B
C
D
E
F
H
I
G
M5 Allen Key x 1
M4 Allen Key x 1
Side Caps x 30
M6 X 25mm Bolt x 4
1
2
3
4
5
6
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 15
Wooden Legs x 4
Metal Plates x 2
2/6
Fittings
Parts
Headboard Legs
Footboard Legs
L R
Nut M8 x 2
Spanner M13 x 1
Spring Washer M8 x 2
Screw 3.5 X 30mm x 2
Screw 3.5 X 18mm x 2

Step Two
Hook the pre-attached metal fixing on the Side Rails (3) over the pre-inserted bolts in the Headboard (1) and
Footboard (2) then tighten the bolts with M5 Allen Key (B) to secure.
Step by step assembly instructions
Step One
M5
M5
Bracket
Side Rail
3
1
1
3
3
2
Bracket
Side Rail
2
3
3/6
B.
Starting with the Headboard (1) insert the Front Legs (5) into the pre-drilled holes on the underside of the
Headboard (1) and twist to secure, as shown in the diagram below.
Leg x 2
5.
1
5
3
F
o
r
H
e
a
d
b
o
a
r
d
O
n
l
y

Step Three
F. D.E.G.
Nut M8 x 2Spanner M13 x 1
STEP 2
For Footboard Only
Screw
3.5 x 30mm x 2 M6 x 25mm x 4
I.
Screw
3.5 x 18mm x 2
Attach Metal Plate (6) with Wooden Leg (5) together as shown in Step 1. Make sure the arrow on the metal plate and
wooden leg line up. Attach together Wooden Leg (5) and Metal Plate (6) using Spring Washer (H) and Nut M8 (E)
then tighten with Spanner M13 (G) and Screw 3.5x18mm (I). Next attach the leg to the Footboard (2) and Side Rail (3)
as shown in Step 3 using Bolt M6x25mm (D) and Screw 3.5x30mm (F). Tighten the bolt with Allen Key M4 (A).
Nut M8 (E)
Spanner M13 (G)
Spring
Washer M8 (H)
3.5 x 18mm (I)
5
6
STEP 1
Legs x 2
RL
6.
Metal plates x 2
H. 5.
Spring
Washer M8x2
2
3
5
6
3.5 x 30mm (F)
M6 x 25mm (D)
A.
M4 Allen Key x 1
M4(A)
x2
6
5
STEP 3
R
2
3
5
6
3.5 x 30mm (F)
M6 x 25mm (D)
M4 (A)
L
4/6

5/6
Bed is ready to use.
4. C.
Step Five
Step Four
4
C
C
C
4
x30
With the curved side facing upwards, insert end of Slats (4) into a Side Cap (C). Use your palms to push
down the Side Caps (C) into the Side Rails (3), as shown in diagram below.
Slats (15 pcs) Side Caps (30pcs)

This Jamie bedstead should be cleaned using a soft damp cloth and dried immediately. Do not
use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural on-going discolouration
process.
Screws holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.
6/6
Care and Maintenance
Safety Instructions
If you require any additional information or have any issues with this product please call
the John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis Partnership 171 Victoria Street, London, SW1E 5NN.
www.johnlewis.com
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.