John Lewis JL Bilbao 820/31102 User manual

1
John Lewis
JL Bilbao Dining Chair
Stock number: 820/31102
Thank you for purchasing this JL Bilbao Dining Chair. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product
Pre-Assembly Preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer from whom
you bought this product.
This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 45 MINUTES to assemble with 1 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
We DO NOT recommend the use of an electric screwdriver whilst assembling this product.

2
Fittings and Parts Checklist
A
Back x 1
G
Cross Bar -3 x 1
B
Textaline Seat x 1
C
Side Chair Left x 1
D
Side Chair Right x 1
E
Cross Bar -1 x 2
F
Cross Bar -2 x 1
Hardware
1
6 x (6x90mm)
4
8 x (6x 20mm)
2
2 x (6x70mm)
5
2 x (6x20mm)
3
2 x (6x45mm)
6
2 x Allen key

3
Step by Step Assembly Instructions
Step One
1. Position the cross bars (2 x E; 1 x F) into the left side of the chair (C)
and attach with 3 x (6x90mm) bolts (1).
2. Fully tighten bolts using the Allen Key (6).
Step Two
1. Position the cross bar (G) into the left side of the chair.
2. Align the right side of chair (D) with cross bars, and attach with 3 x
(6x90mm) bolts (1) as shown in diagram below.
3. Tighten bolts using the Allen Key (6).
NOTE: Do NOT fully tighten the bolts at this stage.
Step Three
1. To attach the Back (A) of the chair, slide into place and align all bolt holes.
2. Use 2 x (6x45mm) bolts(3) to secure the bottom of the back to the seat base
as shown in the diagram below. Only partially tighten bolts at this stage using the
Allen Key (6).
3. Secure the Back (A) to the arm rest using 2 x (6x70mm) bolts (2) and fasten
with 2 x (6x20mm) female part (5).
Step Four
1. Place the Chair frame up-side-down on a clean, dry & smooth surface that will
not scratch the chair frame.
2. Attach the Textaline Seat (B) to the constructed chair using 8 x (6x 20mm)
bolts (4).
IMPORTANT! –When attaching the textaline seat base, partially tighten two bolts
on each side of the chair to hold it in place before securing the Seat Base fully with
the remaining bolts.

4
Step Five
1. Ensure all fittings are fully tightened.
2. Place chair on solid flat surface ensuring all feet are in full contact with the
ground.
3. The Chair is now ready to use
Care and Maintenance
Wood Furniture
This product is made from FSC Eucalyptus and has been painted and sealed with PU paint, suitable for
outside use.
Wood is a natural material and its colour can vary. Wood absorbs and releases moisture so differant
types of weather will greatly influence the long term look of this product.
Wood displays different grain patterns depending on which way they cut - for example, the ‘medullary
ray’ which can appear on oak furniture is a mark of good quality timber - these are just characteristics of
the natural beauty of the wood. Some furniture is also deliberately aged and rustic.
All timber surfaces will change colour and mellow over time. New furniture will initially vary in shade
from items that have been previously purchased.
How to Care for your Wood Furniture
To clean this product you can wash it with a mild detergent, taking care not to scrub too hard to avoid
scratching. Only use a low pressure hose to rinse it, high pressure sprays can encourage the paint to
flake off. Make sure that the product is thoroughly dried with a soft lint free cloth each time you clean it.
Clean up any accidental food or drink spills as quickly as possible to prevent staining.
To extend the product life and appearance it is advisable to store the furniture in a cool dry place over
winter. Ensure that the furniture is clean and completely dry before putting in to storage. Do NOT
enclose the product in a plastic or other non permeable material as this promotes the growth of mildew
and mould. Cover it with a dust sheet or furniture cover allowing the air to circulate around it.

5
Safety Instructions
Never drag furniture when moving it, always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
This furniture has been designed for domestic use only.
Protect furniture from severe weather conditions (e.g. high winds, torrential rain).
Important safety note:
Do NOT stand on the seat of the chair
Do NOT climb on the chair or use as a ladder
Never tilt the chair. Ensure that the chair is always placed on a solid level surface.
This product complies with:
BS EN 581-1: 2006 and BS EN 581-2: 2009-(Domestic Level)
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com