John Lewis Rouen 803/44304 User manual

For product support or spare parts please call
the John Lewis Helpline;
T: 01244 689949
E: [email protected]
Rouen Storage Bed
PRE-ASSEMBLY PREPARATION
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 90 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembl
Do not use power tools to assemble.
y.
If you require any additional information or have any issues with this product please call the
John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
1/8
Thank you for purchasing this Rouen Storage Bed. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
Double
King Size
Stock code: 803/44304
Stock code: 803/44305

Fittings and parts checklist
A
B
C
F
G
D
E
J
H
I
M4 Allen Key x 1 pcs
M5 Allen Key x 1 pcs
Side Plastic Caps x 30 pcs
Spring Washer M8 x 10 pcs
Centre Plastic Caps x 15 pcs
M8 X 16mm Bolt x 8 pcs
M6 X 25mm Bolt x 6 pcs
M6 X 40mm Bolt x 8 pcs
Screw 3.5 x 30mm x 42pcs
Screw 4 x 18mm x 8pcs
Headboard x 1 Footboard x 1 Side Rails x 2
Slats x 30
Bottom Supports x 2 Centre Support x 1 Drawer Sides x 4
Drawer Backs x 2 Drawer Fronts x 2 Drawer Bottoms x 2
Centre Rail x 1 Wooden Legs x 4
Drawer Panels x 2 Drawer Supports x 6
Screw 4 x 50mm x 4pcs
12 3
4 5 6
7 8 9
10 11 12
13 14 15 16
2/8
K
L
M
Spanner M13 x 1 pcs
Nut M8 x 2 pcs
Metal plates x 2 Metal Stopper x 4

Step One
Step Two
Attach Spring Washer M8 (E) and JCBC M8 x 16mm Bolts (F) into the metal fixings onto both Bottom Supports (7)
(only for the top side). Insert the Bottom Supports (7) inside the bed frame as shown in step 2. Next, attach the
Spring Washer M8 (E) and JCBC M8 x 16mm Bolts (F) into the bottom side of metal fixing on the bottom supports.
Loosely tighten the bolts using M5 Allen Key (B).
M8 x 16mm
Bolt
x 8
Spring Washer
M8 x 8
B.
M8 x 16mm
Bolt (F)
Spring Washer
M8 (E)
7
STEP 1
7
3
1
3
7
7
3
2
M5 Allen Key x 1
E. F.
3/8
3
1
2
BRACKET
SIDE RAIL
3
1
BRACKET
SIDE RAIL
2
3
Place metal bracket on Side Rails (3) over pre-inserted bolts in Headboard (1) and Footboard (2) and hand-tighten
to loosely secure parts together. Do not tighten bolts with M5 Allen Key (B) until you have inserted the Centre Rail
in Step Four.
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
STEP FOUR
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
STEP FOUR
3
7
7
Fig 2
M5 Allen Key
(B)
STEP 2

1
5
3
3
2
Screw
4 x 50mm x 4
Step Three
Step Four
1
3
3
2
7
8
7
7
8
7
x1
3
Attach Centre Support (8) to Bottom Supports (7) and secure into place using Screws 4 x 50mm (I) as shown in the
diagram below.
1
M4 Allen Key (A)
M6 x 25mm (G)
M4 Allen Key x 1 M6 x 25mm Bolt x 2
A. G.
AFTER INSERTING CENTRE
RAIL, TIGHTEN ALL FIXINGS
FULLY INCLUDING BOLTS
AT SIDE RAILS (FROM
STEP ONE)
I
Cross head
Screw Driver
Screw 4 x 50mm (I)
Screw 4 x 50mm (I)
4/8
S
T
E
P
1
S
T
E
P
2
Insert Centre Rail (5) into the brackets on the Headboard (1) and Footboard (2). Push down fully and secure in
place using M6 x 25mm Bolts (G). Tighten using M4 Allen Key (A). You can now tighten the bolts with M5 Allen Key (B)
at the Side Rails from Step One so all fastenings are now tightened.

Step Five
Step Six
Insert the Front Legs (6)x2 into the pre-drilled holes on the underside of the Headboard (1) and twist to secure, as
shown in the diagram below.
Legs x 2
G.
6.
Nut M8 (2)
Spanner M13 (1)
Screw
3.5 x 30mm (2) M6 X 25mm Bolt (4)
6
Legs (2)
15.
Metal plates (2)
Spring
Washer M8 (2)
A.
M4 Allen Key (1)
F
o
r
H
e
a
d
b
o
a
r
d
O
n
l
y
5/8
3
1
J.K.L.
Attach the Metal Plate (15) to the bottom of the Footboard (2) using Bolts M6 X 25mm (G)x2. Do not tighten the bolts
until you make adjustment for the screw hole at the Side Rail (3). Insert Wooden Leg (6) into the bottom of the
Metal Plate (15) using Spring Washer M8 (E) and Nut M8 (K). Hold the Nut M8 (K) using Spanner M13 (L) and twist
the Wooden Leg (6) to secure in place. Repeat for other leg.
E. 6.
x2
For Footboard Only
M6 x 25mm (G)
1
7
M4 (A)
M6 x 25mm (G)
M6 x 25mm (G)
1
M4 (A)
M6 x 25mm (G)
7
3.5 x 30mm (J)
3.5 x 30mm (J)
Spanner M13 (L)
Nut M8 (K)
Spring
Washer M8 (E)
15
6
1
STEP 1
STEP 2
Yellow sticker
face down
AFTER INSERTING BOLT M6 x 25MM,
MAKE ADJUSTMENT FOR SCREW HOLE,
THEN INSERT THE SCREW 3.5 X 30MM.
TIGHTEN THE BOLT M6 x 25MM
FIXINGS FULLY.
TWIST WOODEN LEG ONLY
WITHOUT MOVING THE M8 NUT,
SPRING WASHER AND SPANNER
Twist the wooden leg
3
3
3

Step Seven
6/8
Side Plastic Caps (30 pcs)
Centre Plastic Caps (15 pcs)
Slats (30pcs)
4.
C.
D.
4
4
x15
4
4
C
D
D
With the curved side facing upwards, insert 2 Slats (4) into a Centre Plastic Cap (C) followed by a Side
Plastic Cap (D) onto the other end of both slats. Use your palms to push down the centre plastic caps
into the centre rail followed by the side plastic caps into the side rail as shown in diagram below.
Step 1
C
D
4
x30
Step 2
Step Eight
Attach Metal Stopper (16) to the Bottom Support (7) using screw 4 x 18mm (M).
Screw 4 x 18 (8)
16.M.
7
16
9
4x
Metal Stopper x 4

Step Ten
7/8
Attach Drawer Panel (13) to drawer and tighten together using M6 x 40mm Bolt (H). Tighten with
M4 Allen Key (A). Slide drawers into both sides of the bed frame. The bed is now ready for use.
M6 x 40mm x 8
M4 Allen Key x 1
A. H.
13
x2
13
Step Nine
3.5 x 30mm(40)
Cross Head
Screw Driver
J.
To construct the drawers, fix Drawer Back (10) with one end of each Drawer Support (14) using
Screws 3.5 x 30mm (J) as shown in Fig.1, then fix the Drawer Sides (9) to the Drawer Back (10). Next,
insert Drawer Bottom (12) and then fix Drawer Front (11) using Screws 3.5 x 30mm (J) as shown in Fig.2.
Finally, secure the other end of the Drawer Supports (14) to the other side of the drawer and tighten using
a cross head screw driver.
(x2) (x2)
10
10
9
11
12
14
9
(x2)
9
9
14
14
14
Fig. 1 Fig. 2 Fig. 3

Care and Maintenance
Safety Instructions
If you require any additional information or have any issues with this product please call
the John Lewis Helpline on 01244 689949 or email [email protected]
John Lewis Partnership 171 Victoria Street, London, SW1E 5NN.
www.johnlewis.com
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent
adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
8/8
This Rouen Storage Bed should be cleaned using a soft damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration
process.
Bolts holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.