John Lewis Match 81610115 User manual

Please check the pack contents before attempting to assemble this product. A full checklist of compo-
nents is given in this leaflet. If any components are missing, please contact the John Lewis Helpline.
his product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE
WHEN LIFTING to avoid personal injury and (or) damage to the product.
his product takes approximately 60 MINUTES to assemble with 2 PEOPLE.
he fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
If you are missing some fittings please contact our spare parts helpline on 0330 005 9435.
Opening hours are 9am - 5pm Monday to Friday.
Jo n Lewis
Stock Code: 81610115 - 81610114 - 81610113
Matc tall storage unit
hank you for purchasing this Match tall storage unit. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
PRE-ASSEMBLY PREPARATION
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
00203040506070809000 020304050
023456
Ruler/tape
measure Small hammer
Drill Eye protection
Spirit level
Screwdriver
MAT 01/14 rev. 02 - 02/10/14
Page 1

Metal dowel x 8 Cam lock x 8 Wooden dowel x 8
30mm
Wedgex housing x 20 Wedgex dowel x 20
1
13mm Euroscrew x 4
Wall xing set x 2
25mm Nail x 30
27mm Connector x 2
Nail guide x 1
4MAx15 Connect. screw x 2
A B C
G
H I
P P1P2
D E F
L
M N O
Support foot x 4
30mm Screw x 8 Spacer x 4
GI
Levelling Wedge x 2
Page 2
MAT 01/14 rev. 02 - 02/10/14
Fittings checklist

1
1
2
2
3
3
3
3
3
4
Page 3
MAT 01/14 rev. 02 - 02/10/14
Parts checklist

A
A
1x 2
Page 4
Step by step assembly instructi ns
Step One
Attac 4x metal dowels (A) into t e pre-drilled oles on top/bottom panels (1) as s own.
Use a screwdriver to turn fitting (A) clockwise to fix.
1.
D
D
3x 5
Step Two
Attac 4x wedgefix ousing (D) into t e pre-drilled oles on s elves(3) as s own.1.
MAT 01/14 rev. 02 - 02/10/14

B
Right side
left side
Bottom
Bottom
2
2
B
B
B
B
C
C
C
C
D
D
D
D
D
D
D
D
Page 5
MAT 01/14 rev. 02 - 02/10/14
Step by step assembly instructi ns
Step Three
Place 8x cam lock (B) into t e oles on side panels (2) as s own, arrow pointing towards t e bolt.
Attac 8x wooden dowels (C) into t e pre-drilled oles on side panels (2) as s own.
Attac 20x s elf support (D) into t e oles on side panels (2) as s own.
1.
2.
3.

1
1
2
2
12
B
B
A
4
Bottom
Top
Page 6
Step by step assembly instructi ns
Step Four
Attac side panels (2) to top/bottom panels (1) as s own. Ensure metal dowels (A) and wooden dowels
(C) are aligned correctly wit t e oles of matc ing parts before attac ing.
Secure side panels (2) to top/bottom panels (1) using a screwdriver to turn fitting (B) clockwise to fix.
1.
2.
Step Five
Position back panel (4) as s own, back panel oles indicate upper part.1.
MAT 01/14 rev. 02 - 02/10/14

F
F
F
4
Important:
The cabinet MUST
be ‘square’ when the
back is attached.
G
Page 7
MAT 01/14 rev. 02 - 02/10/14
Step by step assembly instructi ns
Step Seven
Attac 4x support foot (L) to bottom wit 8x screw(M).
1.
Step Six
Attac back panel (4) onto back side of t e unit using 30x nails (F), wit t e elp of t e nail guide (G).1.
LM
M
M
M
L
L
L

Ø5mm
I
H
GI
GI
Page 8
Step by step assembly instructi ns
Step Eight
Wit elp of an assistant, carefully stand up t e unit uprig t.1.
Step Ten
Fittings ave been supplied in order to join units toget er.
Place units toget er in t eir final positon.
Decide position w ere to drill t roug using a Ø5 mm bit.
Pus t e Connector (H) into t e ole and t en screw Bolt (I)
in from t e ot er side, tig ten wit a screwdriver.
1.
2.
3.
Step Nine
Use 2x levelling wedge (GI) to level t e unit. 1.
MAT 01/14 rev. 02 - 02/10/14

Page 9
MAT 01/14 rev. 02 - 02/10/14
Step by step assembly instructi ns
O
P
P
P
4
1
2
N
Wall plug and screw not included.
Please see Guide to wall mounting
3
P1
5
P2
Spacer (N) are to be used on both
wall and base units to allow for the
depth of skirting boards, allowing
all of the units to sit flush with one
another.
Step Eleven
To prevent possible overbalancing we recommend t at t is unit is secured to a suitable wall by use of two ‘L’
Brackets (P) fitted to t e top side of t e unit.
Attac t e 2x brackets (P) onto t e top side of t e unit using 4x euroscrew (O).
Pre-fix brackets (P) to wall, Wall plug and screw not included.
Adjust position using (P1), t en fix it.
Insert cap (P2)
! IMPORTANT !
Take care w en drilling t e wall t at you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Wall plug and screw not included. See wall fixing guide at page 11.
1.
2.
3,4.
5

Page 10
MAT 01/14 rev. 02 - 02/10/14
Step by step assembly instructi ns
E
E
3
3
3
3
3
3
Step Twelve
Position t e s elves (3) on t e s elf support (E) as s own.1.