John Lewis Wardrobe 80313215 User manual

Pre-assembly preparation
Please ensure instructions are read in full before attempting to assemble this product
Necessary Tools
St. Ives 2 door 2 drawer wardrobe
Thank you for purchasing St. Ives 2 door 2 drawer wardrobe. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this product.
Stock number: 80313215 ·80313315

This product takes approximately 60 MINUTES to assemble with 2 PEOPLE.
Read this leaflet in full before commencing assembly.
Fittings and parts checklist
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
Please check the pack contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the number
on the front of this assembly instruction.
This product is HEAVY, it should be assembled as near as possible to the point of use.
TAKE CARE WHEN LIFTING to avoid personal injury or damage to the product.
If you are missing some fittings please contact our spare parts helpline on 01691 770 157

Step by step assembly instructions
Step One
Fittings ( E ) must be screwed in to the shelf (04) and (07) holes pridrilled by using screwdriver
and 4x screws ( C )
Lay parts (01) & (10), (02) & (03) and add cams (A). PLEASE PLACE THE PARTS ON A
SMOOTH SURFACE, in order not to scratch the paint.

Step Two
Step Three
Please take part part (07) add two fottings as per picure below.
Part (09) connect with part (07) as per diagram.
Lay part (11) on the ground. PLEASE PLACE THE PARTS ON A SMOOTH SURFACE, in
order not to scratch the paint. All fittings (A)must be screwed into the pre fitted cams on the
front panel (11).

Step Four
Two persons required.
Please attach base (10) as shown per picture. Tighten the base (10) with a screwdriver.
Step Five
Two persons required.
Please position the assembled wardrobe components vertically on the base of the wardrobe as
shown in the picture. Front (11) must attach to wardrobe frame according to the arrows
direction shown. Tighten with a screwdriver.
Please position (02), (03), (04) and (07) parts as shown in the picture. All fittings (A) must go
into prepared holes with the cam. Side panels (02) and (03) must attach to the shelves (04)
and (07) according to the arrows direction shown. If cams don’t lock into place, please use
screwdriver to adjudt them. After all pieces are gathered, please use a screwdriver to tighten
up.

Step Six
Two persons required.
Please attach top (01) as shown. Tighten the top (01) with a screwdriver.
To remove the supporting door systmem please uscrew the middle screw as shown below.
This is a two man job - the other person should secure the other side. Insert drawers (08) to
their place and push the wooden dowels to secure it.

Step Seven
Hanging rail (05) must be placed to pre screwed (Step One) 2x fittings (B) on side panels.
The magnets can be adjusted by hand by turning the front section (see diagram)
Please screw 2x handles (G) into the front doors and secure them with 2x crews (H). Attach
the back panel to the wardrobe, use 32x screws (F) to tighten the panel to the wardrobe.

Care and Maintenance
How to care for your furniture
Safety Instructions
General warnings:
Specific warnings for heavy items:
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
John Lewis Partnership 171 Victoria Street London SW1E 5NN
www.johnlewis.com
Never drag furniture when moving it always lift it. Periodically check all fixings to ensure none
have come loose and re-tighten where necessary. Please take care when handling or moving
the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a
competent person. No liability will be accepted for damage or injury caused by incorrectly
installed or assembled furniture.
It is recommended that before moving heavy objects to a new location they are completely
disassembled to avoid personal injury or damage to the furniture. Please be careful to retain all
fittings when doing this.
St. Ives range is a timeless painted bedroom range in white with brushed metal knob handles
and grey with solid aok flat tops and brushed metal knob handles. Each piece has been
carefully constructed to ensure it will give you years of pleasure.
The natural characteristics of oak may include small cracks, knots, blemishes and grain
pattern variations wich all add to the natural charm and beauty of this furniture product. Each
piece is unique and for this reason, no two pieces within the range will perfectly match.
However there will be harmony between all the pieces you may have purchased.
All timber surfaces will change colour and mellow over time. New furniture will initially vary in
shade from items that have been previously purchased.
Try to avoid prolonged exposure to direct sunlight as this may alter the colour and tone of your
furniture over time.
Any spillages that do happen should be wiped up immidiately with a clean dry lint free cloth to
avoid marking the surface of the furniture.