John Lewis Midcentury Sweep Bed User manual

Midcentury Sweep Bed
MTO
Thank you for purchasing this Midcentury Sweep Bed. Please read the instructions carefully before use to
ensure safe and satisfactory operation of this product.
Double
Please check the pack contents before attempting to assemble this product. A full checklist of components is
given in this leaflet. If any components are missing, please contact customer services on 01244 689949 or email
[email protected].
PRE-ASSEMBLY PREPARATION
This product is HEAVY. It should be assembled as near as possible to the point of use. TAKE CARE WHEN
LIFTING to avoid personal injury and (or) damage to the product.
This product takes approximately 40 MINUTES to assemble with 2 PEOPLE.
The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG CHILDREN.
Read this leaflet in full before commencing assembly.
Please ensure instructions are read in full before attempting to assemble this product.
Necessary Tools
1/6
1
1

Fitting and parts checklist
A
B
C
D
F
G
H
I
L
M
K
J
E
M5 Allen Key x 1
Side Caps x 14
Centre Caps x 7
1
2
3
4
5
6
Headboard x 1
Footboard x 1
Side Rails x 2
Slats x 14
Wide Slats x 16
Centre Rails x 1
Legs x 4
Parts
Fittings
Two-Ways Bolt x 4
M8 X 45mm Bolt x 8
7
M8 Washer x 4
2/6
1
M8 Nut x 4
M13 Spanner x 1
M8 Spring Washer x 8
M6 X 25mm Bolt x 2
M4 Allen Key x 1
Wide Centre Caps x 8
Wide Side Caps x 16

Legs x 4
7.
Step by step assembly instructions
E. F.I.
Step One
Step Two
3/6
To attach the Side Rail (3) with the Headboard (1), start with inserting the Two-Ways Bolt (I) into the pre-drilled holes
on the Siderail (3) as shown in Fig. 1.
Next, you can start to attach the Side Rail (3) and the Headboard (1) with M8 Washer (E) and M8 Nut (F) by opening
the zip at the back of the Headboard (1) as shown in Fig 2.
Do not tighten with M13 Spanner (B) until you have inserted the Centre Rail in the next step.
STEP 2
1
3
Two-Ways Bolt
x 4 M8 Washer x 4 M8 Nut x 4
Two-Ways Bolt (I)
3
Short
Long
Fig.1
STEP 1
PLEASE SCREW A SHORT HEAD
OF THE BOLT TO THE SIDE RAILS
IN ORDER TO ATTACH THE SIDE
RAILS WITH THE HEADBOARD
1
*Open the zip
Fig.2
3
3
Insert the Legs (7) into the pre-drilled holes on the Siderail (3). Twist the legs (7) to secure in place.
(As per diagram below)
3
3
7
7
7
7
3
M8 Washer (E)
M8 Nut (F)
STEP 3
x4

1
1
Lower the Centre Rail (6) into the pre-drilled holes of the Headboard (1) and Footboard (2) and attach with
M6 x 25mm Bolt (M) and fully tighten bolts with M4 Allen Key (L) as shown in Fig.3.
You can now tighten the bolts at the Side Rails from previous step (Step Two) with the M5 Allen Key (A) and
M13 Spanner (B) so all fastenings are now tightened.
Step Three
Step Four
4/6
AFTER INSERTING CENTRE RAIL,
TIGHTEN ALL FIXINGS FULLY
INCLUDING BOLTS AT SIDE RAILS
(FROM STEP TWO)
1
1
3
3
2
1
6
M4 Allen Key
x 1
M5 Allen Key
x 1
A. L.
M6 x 25mm
x 2
M.
B.
M13 Spanner
x 1
Centre Rail
F
i
g
.
3
61
2
And
M4(L)
M6 x 25(M)
F
i
g
.
4
6
1
2
And
M5 Allen Key (L)
F
i
g
.
1
3
1
M5 Allen Key (L)
2
2
3
F
i
g
.
2
Starting with the Headboard (1) attach the Side Rails (3) using the M8 x 45mm Bolt (G) and M8 Spring Washer (H)
into the pre-drilled holes on the Siderail (3). Please do not tighten the bolts yet.
Repeat the step with the Footboard (3). Do not tighten with M5 Allen Key (A) until you have inserted the Centre Rail
in the next step.
M8 X 45mm Bolt
x 8
Fig.1
x2
M8 x 45mm (G) M8 Spring
Washer (H)
H.
M8 Spring Washer
x 8
G.
1
3
3
2
LOOSELY SECURE PARTS
TOGETHER IN ORDER FOR
CENTRE RAIL TO FIT IN
NEXT STEP
2
2
3
F
i
g
.
2
M8 Washer (E)
M8 Nut (F)
M13 Spanner (B)
M8 x 45mm (G)
M8 Spring
Washer (H)

1
1
2 Lines
Normal slats
1 Line
Normal slat
2 Lines
Wide slats
2 Lines
Wide slats
2 Lines
Normal slats
2 Lines
Normal slats
4 Lines
Wide slats
ZONE 2
ZONE 1
ZONE 5
ZONE 7
ZONE 6
ZONE 4
ZONE 3
Diagram 1
D
K
4
5
(x8)
(x7)
4.
5.
C.
D
K.
J.
Side Caps x 14
.
Wide Centre Caps
x 8
Wide Side Caps
x 16
Wide Slats x 16
Slats x 14
5/6
Step Five
Step Six
This bed is now ready to use.
With the curved side facing upwards, insert 2 slats into a centre cap then into 2 side caps on either
end(x15). (Please note the Wide Slats must be inserted with the Wide Centre Caps (J) and Wide
Side Caps (K)). Repeat this process for all slats.
Note: Please see the Diagram 1 below to arrange the slat with the correct system).
4
4
C
J
5
5
Centre Caps x 7
J
K
K
D
D
4
4
5
5
C
1
1

Care and Maintenance
Safety Instructions
If you require any additional information or have any issues with this product please call the customer
services helpline on 01244 689949 or email [email protected].
Never drag furniture when moving it. Always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Any assembly should be carried out by a competent
adult.
No liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
During assembly, children should be kept away from the product due to possible risk of injury.
Do not use this item if any components are missing or damaged.
It is recommended that care is taken when moving heavy objects to a new location to avoid
personal injury or damage to the furniture. Please be careful to retain all fittings when doing this.
This bed should be cleaned using a soft, damp cloth and dried immediately.
Do not use a very wet cloth or allow any liquid contact for a long period of time as this can permanently
damage the surface.
Do not use detergents and do not rub as this can cause permanent damage.
Always protect your bed from direct sunlight as this may accelerate the natural ongoing discolouration
process.
Bolts holding together the bed frame should be tightened regularly.
Please retain this information leaflet for future reference.
This product complies with BS EN 1725:1998.
6/6