Johnson Controls VG7000 Series User manual

Refer to the QuickLIT website for the most up-to-date version of this document.
VG7000 Series Bronze Control Valves Installation Instructions
1
Applications
VG7000 Series Bronze Control Valves are primarily
designed to regulate the flow of water and steam in
response to the demand of a controller in Heating,
Ventilating, andAir Conditioning (HVAC) systems.
Contact the local Johnson Controls® representative for
compatibility concerns before using the VG7000 Series
Bronze Control Valves Technical Specifications table at
the end of this document.
These installation instructions conform to the relevant
and valid European Norm (EN) safety standards, as
well as the current laws and regulations of the
European Union. Qualified personnel are required for
the proper application of these installation instructions.
Qualified personnel are trained in the installation,
mounting, commissioning, operation, and servicing of
pneumatically and electrically actuated VG7000 Series
Bronze Control Valves; they include trainers and
instructors who have the following responsibilities:
• ensure adherence to regional and international
ordinances and requirements
• teach safety standards
• enforce adequate facility safety and protective
operation
• instruct first aid
Location of Valve Data
Each VG7000 Series Bronze Control Valve shipped
from the factory includes a brass tag chained to the
valve bonnet. The tag features technical data about the
valve, including:
•code number of the valve
•flow coefficient Cv of the valve
•maximum allowable fluid temperature of the
controlled media
•manufacturing date code of the valve (as
illustrated in Figure 1)
Installation
Pre-installation Details
Before installing a VG7000 Series Bronze Control
Valves, note the following:
• Be sure to mount the valve in an upright position, in
a conveniently accessible location.
• Protect the electric actuator from dripping water
that could enter the actuator housing and damage
the mechanism or motor.
• Do not cover the actuator with insulating material.
• Allow sufficient clearance to remove the actuator
(see Figure 2, Table 1, and Table 2).
• Pipe the valve with the flow in the direction of the
arrow on the valve body, so that the plug seats
against the flow.
• Wire all electrically actuated valve assemblies in
accordance with applicable electrical code
requirements. Input lines to the actuator must be
wired correctly for the valve to move in the proper
direction.
IMPORTANT: The VG7000 Series Bronze Control
Valves are intended to control saturated steam, hot
water, and chilled water flow under normal
equipment operating conditions. Where failure or
malfunction of the VG7000 Series Valve could lead
to personal injury or property damage to the
controlled equipment or other property, additional
precautions must be designed into the control
system. Incorporate and maintain other devices,
such as supervisory or alarm systems or safety or
limit controls, intended to warn of or protect against
failure or malfunction of the VG7000 Series Valve.
Figure 1: Manufacturing Date Code
Manufacturing Facility
w wy y
M
Week
Year
FIG:mfgd
t
c
d
VG7000 Series Bronze Control Valves
Installation Instructions
VG7000 Part No. 14-1078-6, Rev. M
Release Issued December 2018
*1410786RevM*
14-1078-6 Rev. M

VG7000 Series Bronze Control Valves Installation Instructions
2
Dimensions
IMPORTANT: Take care to prevent foreign material
such as weld slag, thread burrs, metal chips, and
scale from entering the piping system. This debris
can damage or severely impede the operation of the
valve by embedding itself in the seats, scoring the
valve, and ultimately resulting in seat leakage. If the
debris becomes embedded in the seats, subsequent
flushing and filtering of the piping system with the
valve installed does not remedy the problem.
Table 1: Internal National Pipe Thread (NPT) Valve Dimensions, in. (mm)
Valve Size, in. (DN) A B
N.O., N.C., and
Three-Way N.O. N.C. Three-Way
1/2 (DN15) 3 (76) 13/16 (21) 1-9/16 (39) 1-13/16 (46)
3/4 (DN20) 3-7/32 (81) 15/16 (24) 1-5/8 (41) 2-1/8 (54)
1 (DN25) 4-1/8 (104) 1-5/32 (29) 1-3/4 (44) 2-9/16 (65)
1-1/4 (DN32) 4-23/32 (119) 1-11/32 (34) 2 (51) 2-25/32 (70)
1-1/2 (DN40) 5-1/8 (130) 2-5/32 (55) 2-3/4 (70) 3-3/8 (85)
2 (DN50) 5-29/32 (150) 2-1/8 (53) 2-27/32 (72) 3-3/4 (95)
Figure 2: Two-Way Normally Open (N.O.)/Push-Down-to-Close (PDTC),
Two-Way Normally Closed (N.C.)/Push-Down-to-Open (PDTO), and Three-Way Mixing Valve Dimensions,
Fluid Flow Directions, and Port Designations (See Table 1 and Table 2.)
A
D
Outlet
Inlet
B
C
Valve + Actuator
A
D
B
C
Valve + Actuator
Clearance Needed
forActuator Mounting
and Removal
N.O.
(PDTC)
N.C.
(PDTO)
Fig:VG7000

VG7000 Series Bronze Control Valves Installation Instructions
3
Table 2: Valve Assembly Dimensions, in. (mm)
Actuator
Type C1D1
1/2 in.
(DN15) 3/4 in. (DN20) 1in. (DN25) 1-1/4 in. (DN32) 1-1/2 in. (DN40) 2in. (DN50)
Brass Trim Valve Assemblies
V-3000-8012 4-3/4
(120) 4-3/4 (120) 5-31/32 (151) 5-7/8 (149) 5-13/16 (147) 6-3/16 (157) 3-9/16 (90)
V-3000-8003 5-11/32
(135) 5-11/32 (135) 6-9/16 (166) 6-19/32 (167) 6-13/32 (162) 6-13/16 (172) 3-9/16 (90)
V-3801-8001 4 (102) 4 (102) --- --- --- --- 2-3/8 (60)
MP82xx,
MP83xx --- --- 12-23/32 (323) 12-27/32 (326) 13-13/32 (341) 13-13/16 (351) 3-1/2 (89)
VA-4233 8-15/32
(215) 8-15/32 (215) 9-7/16 (240) 9-9/16 (243) --- --- 1-1/2 (38)
VA-715x 7-11/16
(195) 7-11/16 (195) 8-21/32 (220) 8-25/32 (223) 9-11/32 (238) 9-3/4 (248) 2-1/2 (64)
VA-720x --- --- 10-7/16
(265) 10-17/32 (268) 11-1/8 (283) 11-1/2 (293) 4-1/2 (114)
VA-8x2x 6-7/16
(164) 6-7/16 (164) --- --- --- --- 1-1/2 (38)
VA78x0 --- --- 11-23/32
(298) 11-27/32 (301) 12-13/32 (315) 12-13/16 (325) 4-1/2 (114)
Stainless Steel Trim Valve Assemblies2
V-3000-8012 5-7/16
(138) 5-7/16 (138) 6 (152) 6-1/4 (158) --- --- 3-9/16 (90)
V-3000-8003 6-1/16
(153) 6-1/4 (158) 6-19/32 (167) 6-27/32 (173) --- --- 3-9/16 (90)
MP82xx 12-3/4
(324) 13-17/64 (337) 13-39/64 (346) 13-27/32 (352) 14-1/32 (356) 14-15/64 (361) 3-1/2 (89)
MP83xx 12-21/64
(313) 12-35/64 (319) 12-7/8 (327) 13-1/8 (333) 13-19/64 (338) 13-1/2 (343) 3-1/2 (89)
MP84xx --- --- --- --- 17-7/32
(437) 17-27/64 (443) 3-1/2 (89)
MP85xx --- --- --- --- 15-61/64
(405) 16-5/32 (410) 3-1/2 (89)
VA-4233 8-23/32
(221) 8-15/16 (227) 9-9/32 (236) 9-13/16 (249) --- --- 1-1/2 (38)
VA-715x 8-13/32
(214) 8-5/8 (219) 8-31/32 (228) 9-7/32 (234) 9-13/32 (239) 9-5/8 (244) 2-1/2 (64)
VA-720x 9-3/32
(231) 9-5/16 (236) 9-21/32 (245) 9-7/8 (251) 10-3/32
(256) 10-9/32 (261) 4-1/2 (114)
VA78x0 11-15/32
(291) 11-11/16 (297) 12-19/32 (320) 12-27/32 (326) 13-1/32 (331) 13-1/4 (336) 4-1/2 (114)
1. Dimension Cis the overall height above the centerline of the valve body, and dimension Dis the clearance required for
actuator removal (as illustrated in Figure 2).
2. An extended bonnet comes as standard equipment on VG7000 Series Bronze Control Valves with stainless steel trim,
to allow for higher fluid temperatures (100 psig [690 kPa] saturated steam at 338°F [170°C]).

VG7000 Series Bronze Control Valves Installation Instructions
4
Table 3: Two-Way N.O./PDTC and Two-Way N.C./PDTO Union Globe Valve Dimensions, in. (mm)1
Valve Size, in. (DN) E F G
1/2 (DN15) N.O./PDTC 1-1/2 (38) 2-21/32 (68) 13/16 (20)
1/2 (DN15) N.C./PDTO 1-1/2 (38) 2-21/32 (68) 1-17/32 (39)
3/4 (DN20) N.O./PDTC21-9/16 (40) 3-3/32 (79) 15/16 (24)
1 (DN25) N.O./PDTC22-1/16 (53) 4-1/32 (102) 1-5/32 (29)
1-1/4 (DN32) N.O./PDTC22-3/8 (60) 4-19/32 (117) 1-11/32 (34)
1-1/2 (DN40) N.O./PDTC22-9/16 (65) 4-27/32 (123) 2-5/32 (55)
1. See Table 2 for overall assembly height Cand clearance Ddimensions.
2. Sizes greater than 1/2 in. (DN15) are available in N.O./PDTC only.
Figure 3: Two-Way N.O./PDTC and Two-Way N.C./PDTO Union Globe Valve Dimensions (See Table 3.)
E
F
G
Fig:unionglobe
Figure 4: Two-Way N.O./PDTC Union Angle Valve Dimensions (See Table 4.)
E
F
G
Fig:unionangle
Table 4: Two-Way N.O./PDTC Union Angle Valve Dimensions, in. (mm)1
Valve Size, in. (DN) E F G
1/2 (DN15) N.O./PDTC 1-23/32 (44) 2-21/32 (68) 1-7/8 (48)
3/4 (DN20) N.O./PDTC 1-9/16 (40) 3-3/32 (79) 2-1/8 (54)

VG7000 Series Bronze Control Valves Installation Instructions
5
Repair Information
If the VG7000 Series Bronze Control Valve fails to
operate within its specifications, refer to the VG7000
Series Bronze Control Valves Product Bulletin
(LIT-977140) fora list of repair parts andreconditioning
kits available. For a replacement valve, contact the
nearest Johnson Controls representative.
1 (DN25) N.O./PDTC 2-1/16 (53) 4-1/32 (102) 2-9/16 (65)
1-1/4 (DN32) N.O./PDTC 2-3/8 (60) 4-19/32 (117) 2-25/32 (70)
1-1/2 (DN40) N.O./PDTC 2-9/16 (65) 4-27/32 (123) 3-3/8 (85)
1. See Table 2 for overall assembly height Cand clearance Ddimensions.
Table 4: Two-Way N.O./PDTC Union Angle Valve Dimensions, in. (mm)1
Valve Size, in. (DN) E F G
Table 5: Two-Way N.O./PDTC, Two-Way N.C./PDTO, and Three-Way Mixing Union Sweat Valve
Dimensions, in. (mm)1
Valve Size, in. (DN) A B
Two-Way N.O./
PDTC Two-Way N.C./ PDTO Three-Way Mixing
1/2 (DN15), 3/8 in. Tubing 4-3/16 (106) 13/16 (20) 1-17/32 (39) 2-17/32 (64)
1/2 (DN15), 1/2 in. Tubing 4-3/16 (106) 13/16 (20) 1-17/32 (39) 2-17/32 (64)
1/2 (DN15), 3/4 in. Tubing 4-25/32 (122) 13/16 (20) 1-17/32 (39) 2-17/32 (64)
3/4 (DN20) 5-1/16 (129) 15/16 (24) 1-9/16 (40) 3-1/4 (82)
1 (DN25) 6-3/32 (155) 1-5/32 (29) 1-3/4 (44) 3-23/32 (94)
1-1/4 (DN32) 7-9/32 (185) 1-11/32 (34) 2 (51) 4-3/32 (104)
1-1/2 (DN40) 8-19/32 (218) 2-5/32 (55) 2-3/4 (70) 4-29/32 (125)
2 (DN50) 9-7/16 (240) 2-1/8 (53) 2-27/32 (72) 5-19/32 (142)
1. See Table 2 for overall assembly height Cand clearance Ddimensions.
Figure 5: Two-Way N.O./PDTC, Two-Way N.C./PDTO, and Three-Way Mixing Union Sweat Valve
Dimensions (See Table 5.)
A
B
Fig:unionsweat

VG7000 Series Bronze Control Valves Installation Instructions
6
Pre-servicing Details
Before servicing a VG7000 Series Bronze Control
Valve, isolate or disconnect the pneumatic supply or
electricalpowertotheactuatorand note the following:
Valve Removal Details
In addition to observing general mounting guidelines
and National Code Standards, be sure to note the
following before removing a valve from a piping
system:
• Allow hot water or steam systems to cool down
thoroughly before proceeding.
• Drain the piping system to provide a pressure-free
work environment.
• Vent all piping systems that are used in conjunction
with corrosive or aggressive fluids.
• Be sure all work is performed by qualified
personnel only.
Risk of Electric Shock.
Disconnect or isolate all power supplies before
making electrical connections. More than one
disconnection or isolation may be required to
completely de-energize equipment. Contact with
components carrying hazardous voltage can cause
electric shock and may result in severe personal injury
or death.
Risque de décharge électrique.
Débrancher ou isoler toute alimentation avant de
réaliser un branchement électrique. Plusieurs
isolations et débranchements sont peut-être
nécessaires pour -couper entièrement l'alimentation
de l'équipement. Tout contact avec des composants
conducteurs de tensions dangereuses risque
d'entraîner une décharge électrique et de provoquer
des blessures graves, voire mortelles.
Risk of Personal Injury.
Shut off the liquid supply and relieve pressure in the
line before servicing the valve. Contents of liquid lines
could be under pressure and the release of liquid
under pressure may cause severe personal injury.
Risque de blessure.
Couper l'alimentation en liquide et évacuer la
pression présente dans la conduite avant toute
intervention sur la vanne. Les liquides à l'intérieur des
conduites peuvent être sous pression et la libération
soudaine de liquide sous pression risque de
provoquer des blessures graves.
Risk of Property Damage.
Do not apply power to the system before checking all
wiring connections. Short circuited or improperly
connected wires may result in permanent damage to
the equipment.
Risque de dégâts matériels.
Ne pas mettre le système sous tension avant d'avoir
vérifié tous les raccords de câblage. Des fils formant
un court-circuit ou connectés de façon incorrecte
risquent d'endommager irrémédiablement
l'équipement.
IMPORTANT: Make all wiring connections in
accordance with local, national, and regional
regulations. Do not exceed the electrical ratings of
the VG7000 Series Bronze Control Valve.
This product can expose you to chemicals
including lead, which is known to the State
of California to cause cancer, birth defects,
or other reproductive harm. For more infor-
mation, go to www.P65Warnings.ca.gov.
This product is made of copper alloy, which
contains lead. The product is therefore not
to be used on drinking water.

VG7000 Series Bronze Control Valves Installation Instructions
7
Technical Specifications
VG7000 Series Bronze Control Valves (Part 1 of 2 )
Service1Hot Water, Chilled Water, 50/50 Glycol Solutions, or Steam for HVAC
Systems (Fluid Group 1 According to 67/548/EEC)
Valve Body Size/Cv (kv) 1/2 in. 0.73 (0.63), 1.8 (1.6), and 4.6 (4.0)
3/4 in. 7.3 (6.3)
1 in. 11.6 (10)
1-1/4 in. 18.5 (16)
1-1/2 in. 28.9 (25)
2 in. 46.2 (40)
Valve Stroke 5/16 in. (8 mm) for 1/2 or 3/4 in. Valves
1/2 in. (13 mm) for 1 and 1-1/4 in. Valves
3/4 in. (19 mm) for 1-1/2 and 2 in. Valves
Valve Body Rating Meets Requirements of ANSI B16.15, Class 250 (EN 12360).
Valve Ambient Operating
Temperature Limits 35 to 150°F (2 to 65°C)
Valve Assembly Maximum
Allowable Pressure/Temperature Steam Brass Trim: 35 psig (241 kPa) Saturated Steam at 281°F (138°C)
SS Trim: 100 psig (690 kPa) Saturated Steam at 338°F (170°C)
Water Brass Trim: 400 psig (2,756 kPa) up to 150°F (66°C), Decreasing to 365
psig (2,515 kPa) at 248°F (120°C)
SS Trim: 400 psig (2,756 kPa) up to 150°F (66°C), Decreasing to 308 psig
(2,122 kPa) at 338°F (170°C)
Leakage Brass Trim 0.01% of Maximum Flow per ANSI/FCI 70-2, Class 4
SS Trim 0.05% of Maximum Flow
Inherent Flow Characteristics Two-Way
Valves Equal Percentage
Three-Way
Mixing Valves Linear
Rangeability2> 25:1 for the 1/2 in. size, Cv 0.73, valve bodies
> 100:1 for all other VG7000 series valves
Spring Range Pneumatic
Actuators 3 to 6 psig (21 to 41 kPa) for All Except MP8000; 3 to 7 psig (21 to 48 kPa) for MP8000 Only;
4 to 8 psig (28 to 55 kPa);
9 to 13 psig (62 to 90 kPa)
Maximum Recommended
Operating Pressure Drop Steam Brass Trim: 15 psig (103 kPa) for All Valve Sizes
SS Trim: 100 psig (690 kPa) for All Valve Sizes
Water Brass and SS Trim: 35 psig (241 kPa) for 1/2 through 1-1/4 in. Valves; 30
psig (207 kPa) for 1-1/2 and 2 in. Valves
Maximum Actuator Supply
Pressure (Pneumatically
Actuated Valves Only)
25 psig (172 kPa) Maximum
Materials Body: Cast Bronze
Bonnet: Brass
Brass Trim Stem: Stainless Steel
Plug: Brass
Seat: Brass Against Molded Elastomeric Disk
Packing: Self-Adjusting Ethylene Propylene Rubber (EPR) Ring Pack
U-Cups
SS Trim Stem: Stainless Steel
Plug: Stainless Steel
Seat: Stainless Steel
Packing: Spring Loaded Polytetrafluoroethylene (PTFE) and Elastomer
V-Rings

Published in U.S.A. www.johnsoncontrols.com
VG7000 Series Bronze Control Valves Installation Instructions
8
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls
All other marks herein are the marks of their respective owners. © 2018 Johnson Controls
Building Technologies & Solutions
507 E. Michigan Street, Milwaukee, WI 53202
Valve Fluid Operating
Temperature Limits Brass Trim Valve with
Pneumatic
Actuator
For V-3801-8001 and V-3000-8003 Actuators:
35 to 248°F (2 to 120°C) Water; 15 psig (103 kPa) Saturated Steam
For MP82 and V-3000-8012 Actuators:
35 to 284°F (2 to 140°C) Water; 38 psig (262 kPa) Saturated Steam
Brass Trim
Valve with
Electric
Actuator
For VA-8x2x Actuators:
195°F (91°C) Maximum Water; Actuators are not rated for steam.
For VA-4233-xGx-2 Actuators:
35 to 250°F (2 to 121°C) Water; 15 psig (103 kPa) Saturated Steam
For All Other Electric Actuators:
35 to 284°F (2 to 140°C) Water; 38 psig (262 kPa) Saturated Steam
SS Trim Valve
with
Pneumatic
Actuator
All Pneumatic Actuators:
35 to 338°F (2 to 170°C) Water; 100 psig (690 kPa) Saturated Steam
SS Trim Valve
with Electric
Actuator
For VA-4233-xGx-2 Actuators:
35 to 250°F (2 to 121°C) Water; 15 psig (103 kPa) Saturated Steam
For All Other Electric Actuators:
35 to 338°F (2 to 170°C) Water; 100 psig (690 kPa) Saturated Steam
Actuator Ambient Operating
Temperature Limits Refer to the appropriate actuator or linkage kit product bulletin.Ambient operating temperature or other service limitations vary by selected actuator.
Compliance 1/2, 3/4, and
1 in. Valves Pressure Equipment Directive (PED) 97/23/EC: Paragraph 3, Comma 3 (CE Marking not Applicable.)
1-1/4, 1-1/2,
and 2 in.
Valves
Pressure Equipment Directive (PED) 97/23/EC:
Category 1, Mod. A (Subject to CE Marking)
All Valve
Sizes CRN: C1099.9087YTN
1. Proper water treatment is recommended; refer to VDI 2035 Guideline.
2. Rangeability is defined as the ratio of maximum flow to minimum controllable flow.
European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact:
JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY
JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA
JOHNSON CONTROLS
C/O CONTROLS PRODUCT
MANAGEMENT
NO. 22 BLOCK D NEW DISTRICT
WUXI JIANGSU PROVINCE 214142
CHINA
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or
misuse of its products.
VG7000 Series Bronze Control Valves (Part 2 of 2 )
WARNING: BRASS MAY CONTAIN LEAD
To fulfill our obligations towards Article 33, in accordance to the European REACH Regulation No 1907/2006 EC, we hereby inform you that this article contains
the following Substances of Very High Concern mentioned on the Candidate list:
• Lead