Johnson Controls TEC3010 User manual

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone
Thermostat Controllers with Dehumidification Capability
Installation Instructions
1
Refer to the QuickLIT website for the most up-to-date version of this document.
Applications
The TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers are wireless
networked devices that provide control of the following:
• local hydronic reheat valves
• pressure-dependent variable air volume (VAV) equipment with or without local reheat
• two- or four-pipe fan coils
• cabinet unit heaters
• other individual zone equipment using a proportional 0 to 10 VDC control input
The networked models are compatible with the WNC1800/ZFR182x Pro Series Wireless Field Bus System that
enables remote monitoring and programming for efficient space temperature control.All models include a USB port
configuration that reduces installation time by allowing simple backup and restore features from a USB drive, which
enables rapid cloning of configuration between like units.
Some models have occupancy sensing capability built into the device. These thermostat controllers maximize up to
30% energy savings in high-energy usage commercial buildings, such as schools and hotels, during occupied
times by using additional standby setpoints.
All models feature an intuitive UI with backlit display that makes setup and operation quick and easy. Multiple fan
configurations are supported for fan coil equipment types:
• single-speed
• multi-speed (two or three discrete speeds)
• variable-speed/EC motors (0 to 10 VDC control)
Some models support dehumidification on two-pipe fan coil units with reheat, and four-pipe fan coil units with or
without reheat. When no heating is required, the thermostat controller monitors space humidity and activates
dehumidification control as necessary. Heat and reheat is used as required to maintain the space temperature. For
optimal dehumidification performance, use a fan coil unit that has a multi-speed or variable-speed fan (VSF).
TEC3000 Series Wireless Proportional Fan Coil and
Individual Zone Thermostat Controllers with
Dehumidification Capability
Installation Instructions
TEC3020-xx-xxx, TEC3021-xx-xxx, TEC3022-xx-xxx, TEC3023-xx-xxx
Part No. 24-10788-19, Rev. D
Issued July 2018
*241078819D*
24-10788-19, Rev. D
(barcode for factory use only)

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification
Capability Installation Instructions
2
North American Emissions Compliance
United States
Canada
Installation
Parts Included
• one TEC3000 Series Thermostat Controller with integral mounting base
• one installation instructions sheet
IMPORTANT: The TEC3000 Series Thermostat Controller is intended to provide an input to equipment under
normal operating conditions. Where failure or malfunction of the thermostat controller could lead to personal
injury or property damage to the controlled equipment or other property, additional precautions must be
designed into the control system. Incorporate and maintain other devices, such as supervisory or alarm systems
or safety or limit controls, intended to warn of or protect against failure or malfunction of the thermostat
controller.
IMPORTANT: Le TEC3000 Series Thermostat Controller est destiné à transmettre des données entrantes à un
équipement dans des conditions normales de fonctionnement. Lorsqu'une défaillance ou un dysfonctionnement
du thermostat controller risque de provoquer des blessures ou d'endommager l'équipement contrôlé ou un autre
équipement, la conception du système de contrôle doit intégrer des dispositifs de protection supplémentaires.
Veiller dans ce cas à intégrer de façon permanente d'autres dispositifs, tels que des systèmes de supervision ou
d'alarme, ou des dispositifs de sécurité ou de limitation, ayant une fonction d'avertissement ou de protection en
cas de défaillance ou de dysfonctionnement du thermostat controller.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class (B) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la Classe (B) respecte toutes les exigences du Règlement sur le matériel brouilleur
du Canada.

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification
Capability Installation Instructions
3
Location Considerations
Locate the TEC3000 Series Wireless Thermostat Controller:
• on a partitioning wall, approximately 5 ft (1.5 m) above the floor in a location of average temperature, allowing
for vertical air circulation to the TEC
• away from direct sunlight, radiant heat, outside walls, outside doors, air discharge grills, stairwells, and from
behind doors
• away from steam or water pipes, warm air stacks, unconditioned areas (not heated or cooled), or sources of
electrical interference
• outside of a recessed area, metal enclosure, or shelving unit
• on the same building level as the other wireless devices on the same personal area network (PAN)
• at least 2 in. (51 mm) away from any metal obstruction
• in the direct line of sight to other wireless devices on the same PAN. Signal transmission is best if the path
between the TEC3000 and other wireless devices is direct as possible. Line of sight is desirable but not
required. See Table 1 for recommended and maximum distances.
• away from metal and large solid obstructions (including equipment rooms and elevator shafts and concrete or
brick walls) between the TEC3000 and the ZFR Pro Router/Repeater or ZFR Pro Coordinator Radio
• in a clear path between the integrated passive infrared (PIR) occupancy sensor (if equipped) and the space
being monitored
• within range of two or more wireless devices on the same PAN. Redundancy in the layout provides the best
reliability in wireless installations
• at least 20 ft (6 m) from a microwave oven
The effective transmission range and distance for indoor applications vary because of wireless signal absorption
and reflection due to metal obstructions, walls or floors, and furniture found in typical building interiors.
For integrated passive infrared (PIR) models, ensure that the thermostat controller is located centrally where
occupant movement is frequent, and where the unit is not blocked by a plastic tamper resistant enclosure (such as
the GRD10A-608). The plastic enclosure blocks the occupancy sensing capability.
Note: For more details on using ZFR Pro Series communication devices, refer to the WNC1800/ZFR182x Pro
Series Wireless Field Bus System Technical Bulletin (LIT-12012356).
Table 1: Indoor Line-of-Sight Transmission Ranges
Range Type Transmission Distance
WNC Coordinator Radio,
ZFR Pro Repeater TEC3000 Wireless Thermostat Controller
Recommended 50 ft (15.2 m) 50 ft (15.2 m)
Line of Sight, Maximum 250 ft (76.2 m) 100 ft (30 m)

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification
Capability Installation Instructions
4
Note: Allow for sufficient clearance to insert a USB
drive into the USB port.
Use insulating foam pads for installations where wiring
passes through the wall to the thermostat.
Installing the Thermostat Controller
1. Use a 1/16 in. (1.5 mm)Allen wrench or Johnson Controls® T-4000-119 Allen-HeadAdjustment Tool (order
separately) to remove the security screw if it is installed on the top of the thermostat controller cover.
2. Pull the top edge of the cover and open the thermostat controller as illustrated in Figure 2
IMPORTANT: Only connect memory devices to the USB port. Do not use it for charging external devices.
IMPORTANT: The cover is not secured on the bottom. Be careful not to drop the cover.
IMPORTANT: If you are installing more than one thermostat controller, keep track of which cover attaches to
which base. The CPU board number needs to match the Base board number. Otherwise you will encounter an
operation error after you reattach a cover and base that do not belong together as shown in Figure 4. See
Table 2 for TEC3000 model names and code numbers.
IMPORTANT: Use proper Electrostatic Discharge (ESD) precautions during installation and servicing to avoid
damage to the electronic circuits of the thermostat controller.
Figure 1: Thermostat Controller
Shown without Occupancy Sensor,
Dimensions, in. (mm)
FIG:thermostat features
USB Port
Display
Security Screw
1-13/32
(36)
4-23/32
(120)
5-5/8
(143)

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification
Capability Installation Instructions
5
Figure 2: Removing the Security Screw from the Thermostat Controller Cover
(Shown without Occupancy Sensor) (Left) and Removing the Thermostat Controller Cover (Right)
3. Align the thermostat controller mounting base on the wall with the security screw on the top and use the base
as a template to mark the two mounting hole locations. See Figure 3.
Notes:
• If you need to install the thermostat controller on an electrical junction box, use
2-1/2 x 4 in. (63 x 101 mm) square boxes with mud ring covers and avoid smaller 1-1/2 x 4 in.
(38 x 101 mm) square or 3 x 2 in. (76 x 51 mm) boxes. This procedure ensures that you have enough
space for cabling, if needed.
• For surface-mounted applications, use durable mounting hardware, such as wall anchors, that cannot be
easily pulled out of the mounting surface.
4. Pull approximately 6 in. (152 mm) of wire from the wall and insert the wire through the center hole in the
thermostat controller mounting base. See Figure 3.
5. Secure the mounting base to the wall surface using two mounting screws (user supplied) as illustrated in
Figure 3.
Figure 3: Mounting Hole Locations, Dimensions, in. (mm) (Left) and
Securing the Thermostat Controller Mounting Base to the Wall (Right)
FIG:securityscrew
FIG:thermostat cover
4-1/16
(103)
FIG:TEC Backplane2
3-1/4
(83)
FIG:TEC Backplane 1

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification
Capability Installation Instructions
6
Wiring
When an existing thermostat controller is replaced, remove and label the wires to identify the terminal functions.
To wire the thermostat controller:
1. Strip the ends of each wire 1/4 in. (6 mm) and connect them to the appropriate screw terminals as indicated in
Table 3 and Figure 5.
2. Carefully push any excess wire back into the wall.
Note: Seal the hole in the wall with fireproof material to prevent drafts from affecting the ambient temperature
readings.
3. Reattach the wires to the terminal block.
Note: If multiple wires are inserted into the terminals, be sure to properly twist the wires together before
inserting them into the terminal connectors.
Risk of Electric Shock.
Disconnect the power supply before making electrical connections to avoid electric shock.
Risque de décharge électrique.
Débrancher l'alimentation avant de réaliser tout raccordement électrique afin d'éviter tout risque de décharge
électrique.
Risk of Property Damage.
Do not apply power to the system before checking all wiring connections. Short circuited or improperly connected
wires may result in permanent damage to the equipment.
Risque de dégâts matériels.
Ne pas mettre le système sous tension avant d'avoir vérifié tous les raccords de câblage. Des fils formant un
court-circuit ou connectés de façon incorrecte risquent d'endommager irrémédiablement l'équipement.
IMPORTANT: Make all wiring connections in accordance with local, national, and regional regulations. Do not
exceed the electrical ratings of the TEC3000 Series Thermostat Controller.
IMPORTANT: Use proper ESD precautions during installation and servicing to avoid damage to the electronic
circuits of the thermostat controller.

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification
Capability Installation Instructions
7
4. Reattach the thermostat controller cover to the mounting base (bottom side first).
Figure 4: Installing the Thermostat Controller Cover (Left) and Error Code Indicating Mismatched Boards
(Right)
5. Use a 1/16 in. (1.5 mm)Allen wrench or Johnson Controls T-4000-119 Allen-Head Adjustment Tool (order
separately) to reinstall the security screw on the top of the thermostat controller cover. See Figure 2 for security
screw placement.
6. Remove the protective plastic cover sheet from the display.
IMPORTANT: Make sure you reattach the cover that corresponds to its correct base. The CPU board number
needs to match the base board number. Otherwise you will encounter an operation error after you reattach a
cover and base that do not belong together as shown in Figure 4. See Table 2 for TEC3000 model names and
code numbers.
Table 2: TEC3000 Model Names and Code Numbers
Name Code Number Name Code Number
TEC3010 20 TEC3021 25
TEC3011 21 TEC3022 26
TEC3012 22 TEC3023 27
TEC3013 23 TEC3030 28
TEC3020 24 TEC3031 29
IMPORTANT: If the display is dirty, gently wipe it clean with isopropyl alcohol or ethyl alcohol. Do not scrub
hard as to avoid damaging the surface. Do not use other cleaners such as water, ketones, and aromatic
solvents, as they may damage the polarizer.
FIG:close thermostat cover
CPU Board Base Board

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification
Capability Installation Instructions
8
Table 3: Terminal Identification (See Figure 5 for Wiring Diagram)
Terminal Label Function
TEC3020, TEC3021, TEC3022, TEC3023, Proportional FC/VAV
24 V 24 VAC hot from transformer
NC No connect
FAN H Fan high
FAN M Fan medium
FAN L Fan low and fan on
AUX Auxiliary binary output
AUX Auxiliary power
COM124 VAC common from transformer
CLG Cooling command (configurable 0 to 10 V range)
NC No connection
HTG Heating command (configurable 0 to 10 V range)
COM1Common
VSF Variable speed fan command (configurable 0 to 10 V range)
BI2 Configurable binary input 2
BI1 Configurable binary input 1
COS Changeover sensor
R SEN Zone temperature sensor
1. The common terminals are connected and can be used for all inputs, outputs, and 24 VAC power.

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification
Capability Installation Instructions
9
Note: Only one transformer is required for each TEC.
Figure 5: Proportional Wiring Diagram (See Table 3 for Terminal Identification)
Zone Temp
Thermistor
SupplyTemp
Switch
FIG:Model 2 Wiring_output
24 V
R SEN
24V
COS
VSF
COM
SupplyTemp
Thermistor
Vin
Common
EC Motor
or

TEC3000 Series Wireless Proportional Fan Coil and Individual Zone Thermostat Controllers with Dehumidification
Capability Installation Instructions
10
Note: For VAV and 2-pipe systems, connect the valve to the heating output.
Figure 6: Proportional 0 to 10 VDC Control
(Pressure-Dependent VAV)
Figure 7: Proportional 0 to 10 VDC Control
(Pressure-Dependent VAV with Changeover Sensor/Switch)
Figure 8: Proportional 0 to 10 VDC Control
(Pressure-Dependent VAV with Changeover Sensor/Switch and Reheat)
Note: Power to the AUX contact comes from the reheat coil.
Room Temperature Control Thermostat
(Minimum and Maximum Position
Adjusted onActuator)
Proportional
Actuator
FIG:model_2_clng_only
0 to 10
VDC
COS
COM
HTG
FIG:model_2_htng_clng_chngvr
Changeover
Sensor
Room Temperature Control Thermostat
(Minimum and Maximum Position
Adjusted onActuator)
Proportional
Actuator
Supply Air
Temperature Sensor
0 to 10
VDC
COS
24V
HTG
FIG:model_2_htng_clng_chngvr_rht
Changeover
Sensor
Room Temperature Control Thermostat
(Minimum and Maximum Position
Adjusted onActuator)
Heating/Cooling
and On/Off
Duct Heater
Proportional
Actuator
Supply Air
Temperature Sensor
1
C
0 to 10
VDC
COS
COM
24V
HTG
AUX*
AUX*
*The Reheat Installed parameter
must be set to True.