Johnson Controls FX-WRZ Series User manual

Temperature and Relative Humidity
FX-WRZ Series Wireless Room Sensors
Installation Instructions
Application
The Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors are designed to
sense room/zone temperature and transmit wireless temperature control data. Some models also
sense and transmit relative humidity.
In an FX-ZFR Series Wireless Field Bus System application, the sensors communicate with the FX-PC
Controllers through the FX-ZFR18xx Series Router.
In a One-to-One Wireless Room Sensing application, the sensors communicate with an FX-WRZ7860
Wireless Receiver. The FX-WRZ7860 Receiver transfers data to the controller by means of the Sensor
Actuator (SA) communication bus. In a typical application, one FX-WRZ Series Sensor reports to
one FX-WRZ7860 Receiver, but up to five FX-WRZ Series Sensors can be associated with a single FX-
WRZ7860 Receiver for multi-sensor averaging or high/low temperature selection.
FX-WRZ Series sensor models are available with or without an LCD. Depending on the sensor
model, the FX-WRZ Series Sensor can transmit sensed temperature, setpoint temperature, sensed
humidity, and low battery conditions to an associated router or receiver. The FX-WRZ Series Sensors
are designed for indoor, intra-building applications only.
The FX-WRZ Sensors use direct-sequence, spread-spectrum RF technology, and operate on the
2.4 GHz Industrial, Scientific, and Medical (ISM) band. The receiver meets the Institute of Electrical
and Electronics Engineers (IEEE) 802.15.4 standard for low power, low duty cycle RF transmitting
systems.
Important:
Use the FX-WRZ Series Sensors only to provide an input to equipment under normal oper-
ating conditions. Where failure or malfunction of the sensor could lead to personal injury or
property damage to the controlled equipment or other property, additional precautions must
be designed into the control system. Incorporate and maintain other devices, such as super-
visory or alarm systems or safety or limit controls, intended to warn of or protect against fail-
ure or malfunction of the sensor.
North American Emissions Compliance
North American Emissions Compliance
United States
Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Part No. 24-10332-37 Rev. H
2019-03-26 (barcode for factory use only)
FX-WRZTTJ00-0, FX-WRZTTK00-0, FX-WRZTHJ00-0
*241033237H*

Canada
Industry Canada Statement(s)
The term IC before the certification/registration number only signifies that the Industry Canada
technical specifications were met.
Le terme « IC » précédant le numéro d'accréditation/inscription signifie simplement que le produit
est conforme aux spécifications techniques d'Industry Canada.
Installation
Follow these guidelines when installing the FX-WRZ Series Sensors:
• Transport the sensor in the original container to minimize vibration and shock damage.
• Verify that all the parts shipped with the sensor.
• Do not drop the sensor or subject it to physical shock.
• Do not attempt to remove or repair the circuit board from the sensor housing. Other than
battery replacement, the sensor is not user-serviceable.
Parts included
• One FX-WRZ Series Sensor with strips of double-sided adhesive foam tape installed
• One DIP switch overlay for a mesh network application using an FX-ZFR18xx Series Router
• One DIP switch overlay for a One-to-One application using an FX-WRZ7860 Receiver
• One installation instructions sheet
• Two AA alkaline batteries
Dimensions
See Figure 1 for dimensions and physical features of the FX-WRZ Series Sensors.
Figure 1: FX-WRZ Series Sensor; LCD with setpoint adjustment
buttons model shown physical features and dimensions, mm (in.)
Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors Installation Instructions2

Note: Not all features shown on Figure 1 are available on all models.
Special tools needed
• 1.6 mm (1/16 in.) Allen wrench or Johnson Controls® T-4000-119 Allen-Head Adjustment
Tool (order separately) for the tamper-resistant set screw that secures the transmitter to the
mounting base
• straight-blade screwdriver (or coin) for unlocking the sensor housing from the mounting base
locking tab
Mounting
The FX-WRZ Series Sensors can be surface-mounted using the adhesive tape pieces affixed to the
back of the sensors.
Location considerations
Temperature sensor considerations
When locating an FX-WRZ Series Sensor, follow the same best practices used to locate a hard-wired
temperature control, sensor, or thermostat:
• Mount the sensor on an interior wall where it is easily accessible, at least 1.4 m (55 in.) above the
floor, in an area where the temperature is representative of the entire controlled space.
• Avoid enclosed or recessed locations and locations behind curtains, doors, or other obstructions
to the controlled space.
• Avoid locations near entry foyers, doors, windows, supply air ducts, and pipes.
• Avoid locations that are exposed to drafts, direct sunlight, and other sources of heat or cooling.
• Avoid locations where the sensor could be exposed to excessive vibration.
Wireless transmission considerations
In addition to the typical thermostat and temperature control location considerations, follow these
guidelines for locating a sensor in wireless applications:
• Locate the sensor on the same building level as the nearest FX-ZFR18xx Series Router or FX-
WRZ7860 Receiver.
• For best signal transmission, locate the sensor at least 51 mm (2 in.) away from any metal
obstructions.
• Wherever possible, locate the sensor in the direct line of sight to the FX-ZFR18xx Series Router or
FX-WRZ7860 Receiver. Signal transmission is best if the path between the sensor and the router
or receiver is as direct as possible. Line of sight is desirable but not required, as long as the path
is not blocked by large metal objects.
• Avoid metal obstructions (including equipment rooms and elevator shafts) and concrete or brick
walls between the sensor and the FX-ZFR18xx Series Router or FX-WRZ7860 Receiver.
• Do not locate the sensor in recessed areas or metal enclosures.
• In mesh network applications, install the sensors within range of two or more FX-ZFR18xx Series
Routers. Redundancy in the layout provides the best reliability in wireless installations.
• Do not mount the sensor closer than 0.61 m (2 ft) or farther than 30 m (100 ft) from the FX-
ZFR18xx Series Router or 45 m (150 ft) from the FX-WRZ7860 Receiver.
3Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors Installation Instructions

• The recommended indoor line-of-sight transmission range between the sensor and the FX-
ZFR18xx Series Router is 15 m (50 ft).
Installing the FX-WRZ Series Sensor
The FX-WRZ Series Sensor can be surface-mounted using the double-sided adhesive foam tape
factory installed on the back of the device.
Note: The mounting surface, mounting base, and ambient temperature must be at least 10 ° C
(50 ° F) when mounting the sensor base with adhesive foam tape.
To mount the sensor base with adhesive foam tape:
1. Clean the mounting surface to ensure that the adhesive foam tape sticks to the surface.
2. Remove the sensor housing from its mounting base (Figure 2).
Figure 2: Removing the Sensor housing from its mounting
base; LCD Model. Reverse the steps to install the housing)
3. Peel off the protective paper from one side of the factory-installed strips of adhesive foam tape
on the back of the mounting base.
4. When positioned correctly, the arrow between the terminal slots on the inside of the mounting
base should point up. Ensure that the mounting base is upright (tamper-resistant set screw on
top) and press the base firmly onto the clean mounting surface.
5. See Preparing the FX-WRZ Series Sensor for Operation.
Important:
Do not power up the FX-WRZ Series Sensor until a receiver or controller is installed and oper-
ating within the same Radio Frequency (RF) range. If this condition is not met, the sensor
uses a higher-than-normal battery current as it attempts to find a receiver or controller
within range, resulting in reduced battery life.
Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors Installation Instructions4

Removing a mounting base installed with double-sided adhesive foam tape
To remove or relocate a sensor mounted with double-sided adhesive foam tape:
1. Remove the sensor housing from its mounting base (Figure 2).
2. Remove the mounting base from the mounting surface by carefully twisting the base off of the
surface.
3. Remove the adhesive foam tape from the mounting base and clean the mounting base to
remove any leftover adhesive.
Note: New double-sided adhesive foam tape is required to remount the base on the
surface; use Can-Do National Tape (Code No. 99116) adhesive foam tape or its equivalent.
Preparing the FX-WRZ Series Sensor for operation
To prepare the FX-WRZ Series Sensor for operation, and to reinstall the sensor housing on its
mounting base:
1. Place the appropriate DIP switch overlay (based on the application) over the DIP switches. See
Figure 3 through Figure 5.
Figure 3: Mesh Network Application with FX-ZFR18xx series DIP switch overlay
Figure 4: One-to-One Network Application with FX-WRZ7860 DIP Switch Overlay
5Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors Installation Instructions

Figure 5: Back of FX-WRZ Series Sensor Showing DIP Switches and Batteries
2. Set the DIP switches located on the back of the sensor.
For a mesh network application using an FX-ZFR18xx Series Router (Figure 3 and Figure 6),
set the DIP switches as indicated. See Commissioning Multiple FX-WRZ Sensors for information
on commissioning multiple FX-WRZ Series Sensors in an FX-ZFR Series Wireless Field Bus Sys-
tem.
a. Set the POWER switch to OFF.
b. Set the MODE switch to MESH.
c. Set the PAN OFFSET switches according to the job or system plans.
Important:
Ensure that the PAN OFFSET is the same for each FX-ZFR18xx Series Coordinator, FX-
ZFR18xx Series Router, and FX-WRZ Series Sensor in a mesh network. See Figure 6.
Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors Installation Instructions6

Figure 6: Sample DIP switch settings
d. Set the ZONE DIP switches according to the job or system plans.
e. Set the MS/TP ADDRESS DIP switches to match the MS/TP address of the controller with
which the sensor is intended to communicate.
f. Set the TRANSMIT LEVEL switch to 10 mW.
For a One-to-One network application with an FX-WRZ7860 Receiver (Figure 4), set the
DIP switches as indicated, ensuring that the AREA and TRANSMITTER ID switches on the FX-
WRZ7860 Receiver and the FX-WRZ Series Sensors are set to the same value.
a. Set the POWER switch to OFF.
b. Set the MODE switch to 1-to-1.
7Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors Installation Instructions

c. Set the SENSOR# to 199 for applications with only one sensor for each controller. Use the
other settings for additional sensors in applications with a single controller performing
temperature averaging or high/low selection within a zone. Refer to the FX-WRZ7860
One-to-One Wireless Sensing System Technical Bulletin (LIT-12011663) for information on
commissioning multiple FX-WRZ Series Sensors in an FX-WRZ Series One-to-One Wireless
Room Sensing System.
d. Set the AREA switches to match the AREA switch on the FX-WRZ7860 Receiver.
e. Set the Transmitter ID switches to match the Transmitter ID on the FX-WRZ7860
Receiver.
3. Install two AA alkaline batteries (supplied) into the battery compartment on the back of the
sensor. Ensure that the batteries are installed in the proper polarity (Figure 5).
4. If the address DIP switches are set to the correct positions and the temperature sensing
system is ready for operation or testing, set the POWER DIP switch to the ON position (Figure 3
or Figure 4).
Five seconds after the power is applied, the red LED flashes to indicate the firmware revision.
For example, the red LED flashes three times to indicate firmware revision 3.
5. Align the tabs on the bottom edge of the mounting base with the slots on the bottom edge
of the sensor housing, and rotate the sensor assembly onto its mounting base. (Reverse the
procedure shown in Figure 2.)
6. Use a 1.6 mm (1/16 in.) Allen wrench or Johnson Controls T-4000-119 Allen-Head Adjustment
Tool to tighten the tamper-resistant set screw and secure the sensor assembly onto its
mounting base (Figure 2).
Testing signal strength
Once the FX-WRZ sensor is communicating with the FX-ZFR18xx Series Router of FX-WRZ7860
Receiver, press and release the manual occupancy override button to display signal strength.
Press and hold the manual occupancy override button on the FX-WRZ Series Sensor (Figure 1) for
5 seconds or more to place the sensor into Rapid Transmit Mode and initiate a signal strength test
with the associated FX-ZFR18xx Series Router or FX-WRZ7860 Receiver. See Rapid Transmit Mode.
Table 1: FX-WRZ Sensor to FX-ZFR18xx Series Router or FX-WRZ7860 Receiver Wireless Signal
Strength
Flashes Signal strength
3Excellent/Sensor has joined network
2Good/Sensor has joined network
1Weak/Sensor has joined network
0None/Sensor has not joined network
Fast Flash Rate
(8)
Unable to locate associated wireless enabled controller
On LCD models, the signal strength is shown on the display on the face of the sensor (callout in
Figure 7).
Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors Installation Instructions8

Figure 7: Sensor LCD(FX-WRZTHJ, FX-WRZTTJ, FX-WRZTTK Models)
Note: For FX-WRZ Series Sensors with an LCD display, the humidity value may appear as 0.0%
when the sensor is joining a network. This condition is transitory and does not transfer to the
Building Automation System (BAS).
An optional FX-WRZSST-120 Wireless Sensing System Tool can also be used with any FX-WRZ Series
Sensor prior to installation as a site survey tool to determine potential locations for system devices
and the wireless signal strength between the system devices in the application.
Refer to the FX-WRZSST-120 Wireless Sensing System Tool Installation Instructions (Part No. 24-10563-71)
for more information on testing signal strength. For additional location consideration details, also
refer to the following documents:
•FX-ZFR Series Wireless Field Bus System Technical Bulletin (LIT-12011660)
•FX-WRZ7860 One-to-One Wireless Sensing System Technical Bulletin (LIT-12011663)
Temperature setpoint adjustment
You can use the temperature setpoint adjustment buttons on the face of the network sensor to
adjust the temperature setpoint. Press the up arrow button to increase the setpoint or the down
arrow to decrease it. The new setpoint stops flashing and becomes fixed after a few seconds.
°C/°F temperature mode selection
All models include a °C/°F pushbutton on the face of the network sensor to provide temperature
scale options for display. Pressing the pushbutton toggles the temperature mode between
Fahrenheit and Celsius on the LCD.
Rapid transmit mode
Rapid Transmit Mode forces wireless transmissions between the sensor and the parent FX-ZFR18xx
Series Router or FX-WRZ7860 Receiver, and indicates wireless signal strength between the devices.
To force the FX-WRZ Series Sensor into rapid transmit mode:
9Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors Installation Instructions

1. Press and hold the manual occupancy override button on an FX-WRZ Series Sensor for 5 or
more seconds. In rapid transmit mode, the sensor transmits once every 10 seconds for 5
minutes, for a total of 30 update messages. After each transmission, the sensor’s occupancy
LED flashes to indicate the wireless signal strength between the sensor and the associated
parent FX-ZFR18xx Series Router.
2. In addition, when a sensor is in rapid transmit mode, the target FX-ZFR18xx Series Router’s LED
blinks to indicate the received signal strength:
3. If there is a poor signal or no signal, determine why the signal strength between the sensor
and router is not adequate for your application.
4. If there is a good or average signal, the sensor and router are communicating.
Use the sensor’s rapid transmit mode in conjunction with the FX-WRZSST-120 Wireless Sensing
System Tool to perform a site survey, test the wireless signal strength between potential device
locations, and adjust FX-ZFR device locations before installing the devices. For more information on
using the sensor’s rapid transmit mode with the tool, refer to the FX-WRZSST-120 Wireless Sensing
System Tool Installation Instructions (Part No. 24-10563-71).
Manual occupancy override button
Pressing the manual occupancy override button, located on the left side of the sensor, serves
two main functions. First, it temporarily sets the space to an occupied state. Second, it checks the
wireless signal strength of the sensor. The LED on the sensor flashes 3 times to indicate a strong
signal, 2 times to indicate a good signal, or 1 time to indicate a marginal signal. For sensors with an
LCD display, a number of bars on the display indicates wireless signal strength (3 bars for a strong
signal, 2 bars for a good signal, or 1 bar for a marginal signal).
Commissioning multiple FX-WRZ Sensors
Mesh mode
You can add up to nine FX-WRZ Series Sensors for each FX-PCG, FX-PCA, or FX-PCV in mesh mode.
The Zone DIP switches on the FX-WRZ Sensor relate to the Zone Netsensor (SA Bus device) address
configured for the sensor in the Controller Configuration Tool (CCT). For example, if you set the
Zone DIP switches to a value of 3 (that is, DIP switch 1 and 2 are set to ON), you must use Zone
Netsensor address 202 in the CCT. You can add up to nine FX-WRZ Sensors for each controller. You
can use any nine of the sixteen available Zone Netsensor address settings at a time.
The meshmode of operation is intended for use with the FX-ZFR18xx Series Coordinator and FX-
ZFR18xx Series Router. Table 2describes the Zone DIP switch settings for the wireless applications in
mesh mode.
Table 2: Zone switch and SA bus settings when using multiple FX-WRZ Sensors 1
Zone DIP switch ON Zone Netsensor (SA Bus Device) address setting
None (All OFF) 199
1200
2201
1 and 2 202
4203
1 and 4 204
2 and 4 205
1, 2, and 4 206
Temperature and Relative Humidity FX-WRZ Series Wireless Room Sensors Installation Instructions10