Jung BT 1001 Series User manual

Operating instructions
JUNG HOME push-button 1-gang, battery-powered
Art. no. BT..1001
JUNG HOME push-button 2-gang, battery-powered
Art. no. BT..1002
22.09.2023
32405713 J0082405713
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: [phone]
Telefax: [phone]
[email protected]
www.jung.de
Product image non-binding

Table of contents
1 Safety instructions ............................................................................................................ 3
2 Device components .......................................................................................................... 3
3 Intended use..................................................................................................................... 4
4 Product characteristics ..................................................................................................... 5
5 Operation.......................................................................................................................... 5
6 Mounting........................................................................................................................... 6
7 Commissioning ................................................................................................................. 8
8 Resetting the device to the factory setting...................................................................... 10
9 Dismantling..................................................................................................................... 11
10 Technical data ................................................................................................................ 12
11 List of functions and parameters .................................................................................... 13
12 Accessories .................................................................................................................... 14
13 Conformity ...................................................................................................................... 14
14 Warranty ......................................................................................................................... 14
2 / 15
32405713 22.09.2023
J0082405713
JUNG HOME push-button, battery-powered

1 Safety instructions
This device or its accessories are supplied with batteries in the form of button cells.
DANGER! Batteries can be swallowed. This can lead directly to death by suffocation.
Dangerous substances may cause severe internal burns leading to death within 2
hours.
Keep new and used batteries away from children.
Do not use devices if the battery compartment does not close securely and keep
away from children.
If you suspect that a battery has been swallowed or is in any orifice of the body, seek
immediate medical attention.
WARNING! Improper handling of batteries can result in explosion, fire or chemical
burn due to leakage.
Do not heat or throw batteries into fire.
Do not reverse polarity, short-circuit or recharge batteries.
Do not deform or disassemble batteries.
Replace batteries only with an identical or equivalent type.
Remove empty batteries immediately and dispose of in an environmentally friendly
manner.
Remove empty batteries immediately and dispose of in an environmentally
friendly manner. Do not throw batteries into household waste. Consult your
local authorities about environmentally friendly disposal. According to statutory
provisions, the customers are obligated to return used batteries.
Read the instructions in full, observe them and keep them for future reference.
2 Device components
Figure1: JUNG HOME push-button 1-gang, battery-powered
JUNG HOME push-button, battery-powered
3 / 15
32405713 22.09.2023
J0082405713

Figure2: JUNG HOME push-button 2-gang, battery-powered
(1) Base plate
(2) Fastening screws for the base plate
(3) Design frame
(4) Push-button module with battery compartment on rear side
(5) Fastening screws for push-button module
(6) Rocker
(7) Light guide (status LED)
LED indication during operation (display goes out after 5 seconds)
Green* If the output is switched on, the venetian blind, shut-
ter and awning move
Orange* If the output is switched off, the venetian blind, shut-
ter and awning are stationary
Red Disabling function active, e.g. continuously ON/OFF
Flashing green/red Device update is being performed
Slow flashing green Push-button found in configuration mode
Slow triple red flashing, after
pressing button
Low battery charge level
White on a few seconds, then
off
Battery charge level is measured (only after ex-
change of battery)
*Colour adjustable
3 Intended use
– Operation, e.g. of venetian blinds, shutters, awnings, lighting or fans
– Wireless connection to devices from the JUNG HOME system
– Mounting on appliance box with dimensions according to DIN 49073
– Screw fastening on walls or adhesive mounting on smooth surfaces
JUNG HOME push-button, battery-powered
4 / 15
32405713 22.09.2023
J0082405713

4 Product characteristics
– Commissioning using JUNG HOME app on mobile end device (smartphone or
tablet) via Bluetooth
– Operation of top, bottom and full surface with up to two linked functions per
rocker
– Using buttons to operate the actuator when in use or the wirelessly linked
JUNG HOME actuator
– Using buttons to control central functions or call up scenes
– Multi-colour status display
– Actuator state feedback via status LED
– Message of battery status via LED and app
– Disabling of local operation
– Bluetooth SIG Mesh for fully encrypted wireless communication
– Updating via JUNG HOME app
– Using buttons to trigger disabling function and restraint
5 Operation
All settings and operations can be configured individually using the JUNG HOME
app.
Configuration in the JUNG HOME app: The default setting with the "rocker" operating
concept is described in the table.
Type of operation Brief press Long press
Switching1Switch on alternately at top,
bottom or with full surface
Switch on at top, bottom of
with full surface alternately
Dimming1Switch on at top, bottom of
with full surface to switch-
on brightness / switch off
alternately
Top: dim brighter / bottom:
dim darker
Move venetian blind / shut-
ter / awning2Stop or adjust the slats Top: move up / bottom: move down
Heating1Increase the target temper-
ature at the top by 0.5 °C /
Decrease the target tem-
perature at the top by 0.5
°C
–
Operating scenes1Call up scene at top or bot-
tom
Call up scene at top or bot-
tom
Operating an area
(group)1/2 Depending on the unit, as described for switching,
dimming, venetian blinds
and heating
Depending on the unit, as
described for switching,
dimming, venetian blinds
and heating
JUNG HOME push-button, battery-powered
5 / 15
32405713 22.09.2023
J0082405713

Type of operation Brief press Long press
Disabling function (lock-out
protection, restraint)1– Top: activate / bottom: de- activate
Changing the colour tem-
perature (with DALI insert)
– Top: increase colour tem-
perature / bottom: decrease
colour temperature
1 Brief push-button action < 0.4 s < long push-button action
2 Brief push-button action < 1 s < long push-button action
Configuration in the JUNG HOME app: "button" operating concept
Type of operation Brief press Long press
Switching1Alternately switch on /
switch off
Alternately switch on /
switch off
Dimming1Alternately switch on /
switch off switch-on bright-
ness
Alternately dim brighter /
dim darker
Move venetian blind / shut-
ter / awning2Stop or adjust the slats Alternately move up / move down
Heating1– –
Operating scenes1Recalling scenes Recalling scenes
Operating an area
(group)1/2 Depending on the unit, as described for switching,
dimming, venetian blinds
and heating
Depending on the unit, as
described for switching,
dimming, venetian blinds
and heating
Disabling function (lock-out
protection, restraint)1– –
Changing the colour tem-
perature (with DALI insert)
– Alternately increase colour
temperature / decrease col-
our temperature
1 Brief push-button action < 0.4 s < long push-button action
2 Brief push-button action < 1 s < long push-button action
6 Mounting
The communication of the JUNG HOME devices and linked mobile end devices is
carried out in wireless mode within the range of the Bluetooth Mesh network.
Wireless signals can be affected in their range through:
– Number, thickness, position of ceilings, walls and other objects
– Material type of these objects
– High-frequency interfering signals
Observe the following fitting instructions to maximise the range:
JUNG HOME push-button, battery-powered
6 / 15
32405713 22.09.2023
J0082405713

– Plan the positions and number of JUNG HOME devices to keep the number of
ceilings and walls between two devices as low as possible
– If JUNG HOME devices are installed on both sides of a solid wall, they should
be positioned as close as possible to each other on the opposite sides of the
wall. This keeps the attenuation of the wireless signal through the wall as low
as possible
– When planning, observe that the number of building materials and objects that
attenuate the wireless signal strongly (e.g. concrete, glass, metal, insulated
walls, water tanks, pipelines, mirrors, book cabinets, storage rooms and refri-
gerators) on the connection line between JUNG HOME devices is as low as
possible
– Keep a distance of at least 1 m from devices that emit high-frequency signals
(e.g. microwave, motors) or run with wireless signals at 2.4 GHz (e.g. WLAN
router, baby monitor, IP cameras, wireless loudspeakers etc.)
DANGER!
Electrical shock on contact with live parts in the installation environment.
Electric shocks can be fatal.
When mounting in a multiple combination, disconnect 230 V devices. For this, switch
off all corresponding circuit breakers, secure against being switched on again and
check that there is no voltage.
Prior to mounting, insert battery (see chapter "Commissioning").
￭ Screw or glue the base plate (1) to an even surface. The TOP/OBEN label has
to be at the top.
￭ Attach design-frame (3) to the base plate.
￭ Fasten the push-button module (4) to the base plate with the supplied screws
(5).
￭ Snap on the rocker (6) (see figure 1) and (see figure 2).
Information on gluing mounting
The substrate must be flat and free of dust and grease.
￭ Remove the rear, unpunched film of the enclosed adhesive pad.
￭ Align the adhesive pad, stick it to the surface and smooth it out. Remove air
bubbles.
￭ Remove the two inner segments of the front film.
￭ Align the base plate to the external punching and stick it on.
In the case of multiple combinations, cut off the abutting sides using a ruler
and a cutter. (see figure 3).
JUNG HOME push-button, battery-powered
7 / 15
32405713 22.09.2023
J0082405713

Figure3: Cutting the adhesive pads for multiple combinations
7 Commissioning
Inserting the battery
Observe the safety instructions for the batteries. Keep contacts of batteries
and device free of grease.
￭ With the device mounted, carefully remove the rocker (6) from the push-button
module (4) (see figure 1), (see figure 2) and unscrew the push-button module
(4).
￭ Apply battery to the positive contact on the side of the battery holder. Observe
polarity: the positive pole of the battery must be at the top.
￭ Press gently on battery to snap it in.
￭ Mount the push-button module (4) on the base plate and snap on the rocker
(6).
Commissioning with app
Prerequisite: the JUNG HOME device has not yet been made a participant in a
Bluetooth Mesh network; otherwise reset the device to factory defaults.
If a Bluetooth Mesh network (project) does not yet exist, start by creating a new pro-
ject for the first JUNG HOME device in the JUNG HOME app.
If a Bluetooth Mesh network already exists, the project file for this network must be
opened in order to pair the new device.
This battery-powered JUNG HOME device always requires a mains-supplied
JUNG HOME device as a so-called “Friend node”. The mains-supplied device
must be within range (typ. 30 m) of this device and added to the BT-Mesh net-
work before the battery-powered device.
After inserting the battery, the device is automatically in pairing mode for 2
minutes.
JUNG HOME push-button, battery-powered
8 / 15
32405713 22.09.2023
J0082405713

Figure4: Commissioning
￭ Activate pairing mode manually:
Press the left button over entire surface for longer than 4 seconds.
The status LED flashes slowly in blue. Pairing mode is active for two minutes.
￭ Start the JUNG HOME app.
The app shows all devices in pairing mode.
￭ Select a device in the app.
To identify the selected device, its status LED flashes more quickly in blue.
￭ Add the device to the project.
The status LED lights up in blue for five seconds to confirm that pairing was
successful.
If the status LED flashes red very fast, pairing has failed and needs to be re-
tried.
The JUNG HOME app can then be used to link devices wirelessly and config-
ure the parameters and operation (see list of functions and parameters).
Once the commissioning of the JUNG HOME project has been completed,
hand over the project file to the customer.
JUNG HOME push-button, battery-powered
9 / 15
32405713 22.09.2023
J0082405713

Besides basic commissioning, the JUNG HOME app enables device updates and
convenient operation of further individual configuration options:
– Link: A button, binary input or motion sensor can be controlled by linking it to a
load (e.g. dimmer, socket, switching output, shutter, etc.). Several loads can
be controlled together by linking them to an area or scene.
– Area: Different loads (e.g. dimmer, socket, switching output, shutter, etc.) can
be grouped in an area to allow them to be controlled together.
– Scene: Different loads (e.g. dimmer, socket, switching output, shutter, etc.)
can be grouped in a scene so that, by calling up a scene, each load assumes
the load status stored in the scene.
8 Resetting the device to the factory setting
If local operation is disabled, resetting to the default setting can only be per-
formed within 2 minutes after removing the battery for at least 10 seconds and
reinserting the battery.
If the device has already been added to a project with the JUNG HOME app, it
can be reset also to the default setting in one step with the "Delete device"
function from the app.
If the device cannot be reset to the default settings with the app or the app is not at
hand:
JUNG HOME push-button, battery-powered
10 / 15
32405713 22.09.2023
J0082405713

Figure5: Factory reset
￭ Press the left button over its entire surface for longer than 20 seconds until the
status LED quickly flashes red.
￭ Release the button and press it briefly once again within 10 seconds.
The status LED flashes in red more slowly for approx. five seconds. The
device has been reset to the default setting.
After resetting the device to the default setting, it must be removed from the
JUNG HOME app provided it has not already been deleted from the app.
9 Dismantling
The rockers can be dismantled using a dismantling wedge or a screwdriver.
The recesses are intended for a blade width of up to 4 mm.
JUNG HOME push-button, battery-powered
11 / 15
32405713 22.09.2023
J0082405713

Figure6: Dismounting the rocker from the side
Figure7: Dismounting the rocker from above
10 Technical data
Rated voltage DC 3 V
Ambient temperature -5 ... +45°C
Storage/transport temperature -25 ... +70°C
Battery type 1 x lithium CR 2450N (recommended) or CR
2450
Radio frequency 2.402 ... 2.480 GHz
Transmission capacity max. 10 mW, Class 1.5
Transmission range (inside building) Typ. 30 m
JUNG HOME push-button, battery-powered
12 / 15
32405713 22.09.2023
J0082405713

11 List of functions and parameters
The JUNG HOME app can be used to configure all functions of the JUNG HOME
device and its behaviour in the Bluetooth Mesh project for the respective individual
purposes.
All devices created in the JUNG HOME app can be used independently and set sep-
arately.
To reach the configuration mode:
￭ Select the battery-powered push-button in the app.
￭ Press any button on the device in order to activate the configuration mode.
Parameters Setting options,
Default setting
Explanations
Operating
concept
Rocker, button
Default setting: rocker
Rocker: The operation of the button at the
top or button applies to the same load,
same area or same disabling function.
Operation at the top or bottom usually
leads to directly opposite reactions. (E.g.
light on/off, brighter/darker, move up/
down)
Button: Operation of the button at the top
or bottom applies to different loads, areas
or scenes. When controlling loads or
areas, renewed operation of the same
pressure point will lead to opposite reac-
tions (e.g. light on/off, brighter/darker, up/
stop/down).
Behaviour of the
status LED
when switched
on or moving
Colour selection
Default setting: green
LED colour and brightness**: when load
is switched on, venetian blind / shutter /
awning moves.
Behaviour of the
status LED
when switched
off or stationary
Colour selection
Default setting: orange
LED colour and brightness** when a load
is switched off or a venetian blind / shut-
ter / awning is stationary.
JUNG HOME push-button, battery-powered
13 / 15
32405713 22.09.2023
J0082405713

Parameters Setting options,
Default setting
Explanations
Operating lock No lock, factory reset
lock, operating lock
Default setting: no lock
Factory reset lock: prevents resetting on
the device and hence the removal from a
project and pairing again by unauthorised
persons. After the mains voltage returns,
the factory reset lock is deactivated for
two minutes.
Operating lock: prevents normal opera-
tion on the device and hence the load
from being controlled. This lock can be
used, for example, to restrict manual ac-
cess temporarily.
Operation via the app remains possible.
The operating lock cannot be deactivated
on the device.
** Available by update in the future: You can find notes on updates and dates at
www.jung.de/JUNGHOME
12 Accessories
1-gang rocker Art. no. ..101 KO5..
2-gang rocker Art. no. ..102 KO5..
13 Conformity
Albrecht Jung GmbH & Co. KG hereby declares that the radio system type art. no.
BT..1001 and BT..1002 meets the directive 2014/53/EU. You can find the full article
number on the device. The complete text of the EU Declaration of Conformity is
available under the Internet address:
www.jung.de/ce
14 Warranty
The warranty is provided by the specialist trade in accordance with statutory require-
ments.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: [phone]
Telefax: [phone]
[email protected]
JUNG HOME push-button, battery-powered
14 / 15
32405713 22.09.2023
J0082405713

www.jung.de
JUNG HOME push-button, battery-powered
15 / 15
32405713 22.09.2023
J0082405713