Jung KNX 5071 TSM Operator's manual

Product documentation
Standard push-button module, 1-gang
Art. No. 5071 TSM
Standard push-button module, 2-gang
Art. No. 5072 TSM
Standard push-button module, 3-gang
Art. No. 5073 TSM
Standard push-button module, 4-gang
Art. No. 5074 TSM
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
Telefon: +49.23 55.8 06-0
Telefax: +49.23 55.8 06-2 04
[email protected]
www.jung.de
Service Center
Kupferstr. 17-19
44532 Lünen
Germany
Issue: 09.04.2013
6523x320

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
Contents
1 Product definition 3 ................................................................................................................
1.1 Product catalogue 3 ...........................................................................................................
1.2 Function 3 ..........................................................................................................................
1.3 Accessories 4 ....................................................................................................................
2 Installation, electrical connection and operation 5 .............................................................
2.1 Safety instructions 5 ..........................................................................................................
2.2 Device components 6 ........................................................................................................
2.3 Fitting and electrical connection 8 .....................................................................................
2.4 Commissioning 9 ...............................................................................................................
2.5 Operation 11 ......................................................................................................................
3 Technical data 12 ....................................................................................................................
4 Software description 13 .........................................................................................................
4.1 Software specification 13 ...................................................................................................
4.2 Software "Standard TSM 110x11" 15 ................................................................................
4.2.1 Scope of functions 15 .................................................................................................
4.2.2 Notes on software 16 .................................................................................................
4.2.3 Object table 17 ...........................................................................................................
4.2.3.1 Objects for rocker or button functions 17 ............................................................
4.2.3.2 Objects for status LED 19 ...................................................................................
4.2.3.3 Object for energy saving mode 20 ......................................................................
4.2.4 Functional description 21 ...........................................................................................
4.2.4.1 General settings 21 .............................................................................................
4.2.4.1.1 Operation concept and button evaluation 21 ..............................................
4.2.4.1.2 Operation LED 22 .......................................................................................
4.2.4.2 Rockers and button functions 23 ........................................................................
4.2.4.2.1 Switching function 23 ..................................................................................
4.2.4.2.2 Dimming function 24 ...................................................................................
4.2.4.2.3 Blind function 25 ..........................................................................................
4.2.4.2.4 Value transmitter function 26 ......................................................................
4.2.4.2.5 Scene extension function 27 .......................................................................
4.2.4.3 Status LED 28 .....................................................................................................
4.2.4.4 Energy saving mode 29 ......................................................................................
4.2.4.5 Delivery state 31 .................................................................................................
4.2.5 Parameters 32 ............................................................................................................
5 Appendix 38 .............................................................................................................................
5.1 Index 38 .............................................................................................................................
Product documentation
Page 2 of 39

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
1 Product definition
1.1 Product catalogue
Product name: Standard push-button module, 1-gang / Standard push-button module, 2-gang
/ Standard push-button module, 3-gang / Standard push-button module, 4-
gang
Use: Sensor
Design: FM (flush-mounted)
Art. No. 5071 TSM / 5072 TSM / 5073 TSM / 5074 TSM
1.2 Function
Push button functions
When its buttons are pushed, the standard pushbutton sensor modules send telegrams to the
KNX, depending on the ETS parameter settings. These can be, for instance, telegrams for
switching or push button control, for dimming or for controlling blinds. It is also possible to
program 1-byte value transmitter functions (e.g. dimming value transmitters).
The pushbutton sensor modules consist of several control surfaces. The operation concept can
be configured in the ETS either as a rocker function or alternatively as a push button function
(only "Switching" function). With the rocker function, two neighbouring control surfaces are
combined into one rocker switch. In the pushbutton function, each control surface is evaluated
as single-surface operation.
LED functions
The Standard push-button modules have one red status LED for each rocker switch. The status
LEDs can be switched on or off permanently, or can function as a status indicator. As an
alternative, with the aid of separate communication objects, they can signal widely varying
display information completely independently of the push-button function, e.g. operation states
of lighting systems or room temperature controllers.
An operation LED can optionally serve as an orientation light. The colour of the operation LED
can be configured in the ETS (red, green, blue). In programming operating mode, the operation
LED flashes permanently with a frequency of approx. 8 Hz.
Energy saving mode
The device has an energy saving mode to save electrical energy during operation. If the
function is used, the device switches to the energy saving mode after a preset time without
operation or controlled by an external telegram to a separate object, and switches off the
signalling function of the device. The energy saving mode can be deactivated by an operation or
by a special telegram. Afterwards, the device is fully functional again.
Bus coupling unit
The pushbutton sensor modules contain a bus coupling unit and thus can be connected directly
to the bus line.
Page 3 of 39

Product definition

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
1.3 Accessories
Cover kit 1-gang, complete Art. No. ..501 TSA..
Cover kit 2-gang, complete Art. No. ..502 TSA..
Cover kit 3-gang, complete Art. No. ..503 TSA..
Cover kit 4-gang, complete Art. No. ..504 TSA..
Page 4 of 39

Product definition

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
2 Installation, electrical connection and operation
2.1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons. The
applicable accident prevention regulations must be observed.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Danger of electric shock. Make sure during the installation that there is always sufficient
insulation between the mains voltage and the bus. A minimum distance of at least 4 mm
must be maintained between bus conductors and mains voltage cores.
Use only the enclosed plastic screws for fastening to the supporting frame! Otherwise
safe operation cannot be ensured. Electrostatic discharges can cause defects in the
device.
Do not open device or operate it beyond the technical specification.
Page 5 of 39

Installation, electrical connection and operation

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
2.2 Device components
Device components of standard push-button sensors TSM
1 2
(1)
(1)
(2)
(4)
(3)
Figure 1: Front view, standard pushbutton sensor module, 1-gang
(1) 2 control surfaces configurable as rocker 1 or as buttons 1…2.
(2) Labelling field (white)
(3) 1 operation LED (red, green, blue)
(4) 1 status LEDs (red)
1 2
3 4
(5)
(5)
(7)
(6)
(8)
(8)
Figure 2: Front view, standard pushbutton sensor module, 2-gang
(5) 4 control surfaces configurable as rocker 1...2 or as buttons 1…4.
(6) Labelling field (white)
(7) 1 operation LED (red, green, blue)
(8) 2 status LEDs (red)
Page 6 of 39

Installation, electrical connection and operation

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
1
2
3
4
5
6
(9)
(9)
(9)
(11)
(10)
(12)
(12)
(12)
Figure 3: Front view, standard pushbutton sensor module, 3-gang
(9) 6 control surfaces configurable as rocker 1...3 or as buttons 1…6.
(10) Labelling field (white)
(11) 1 operation LED (red, green, blue)
(12) 3 status LEDs (red)
1
2
3
4
5
6
7
8
(15)
(14)
(13) (13)
(16)
Figure 4: Front view, standard pushbutton sensor module, 4-gang
(13) 8 control surfaces configurable as rocker 1...4 or as buttons 1…8.
(14) Labelling field (white)
(15) 1 operation LED (red, green, blue)
(16) 4 status LEDs (red)
i The pushbutton sensor modules can be integrated into the switch programs A500, LS990
or CD500.
Page 7 of 39

Installation, electrical connection and operation

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
2.3 Fitting and electrical connection
Installing the push button sensor and connecting it
2x (20)
2x (23)
(17) (18) (21)
(22)
(23)
(19) (20)
Figure 5: Installing the push-button module
(17) Supporting frame
(18) Design frame
(19) Button sensor module
(20) Fastening screws
(21) Design control surfaces
(22) KNX connection terminal
(23) Box screws
o Mount supporting frame (17) in the right orientation on an appliance box. Note the TOP
marking. Use the enclosed box screws (23).
o Position the decorative frame (18) on the supporting frame.
o Connect the push button module (19) with KNX connection terminal (22), which is
connected to the KNX bus line, on the rear side of the module. Run the connection cable
downwards from the push button module and then into the accessory socket from the rear.
o Attach the push button module onto the supporting frame.
o Fasten push button module to supporting frame using the enclosed plastic screws (20).
Tighten the plastic screws only lightly.
o Before mounting the control surfaces (21), load the physical address into the device (see
page 9-10).
Page 8 of 39

Installation, electrical connection and operation

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
2.4 Commissioning
After connection and mounting, the pushbutton sensor module can be put into operation. The
start-up procedure is basically confined to programming with the ETS and attaching the
decorative control surfaces.
i The extension module does not receive any physical address of its own. It is activated by
the application program loaded in the basic module.
Programming the physical address
The pushbutton sensor does not have a separate programming button or LED. Programming
mode is activated by a defined and time-delayed press of the upper left and lower right of the
pushbutton. Programming mode is signalled by flashing operation LED. To program the
physical address, the decorative control surfaces can be snapped onto the device.
(26)
(27)
Figure 6: Buttons for activating Programming mode
i If the device does not receive any application software, or the wrong application software,
then the operation LED (Colour: blue) flashes slowly.
For commissioning, the pushbutton sensor module must be connected and the bus voltage
switched on.
o Activate Programming mode. Press button at the top left (26) and keep it depressed
(figure 6). Then press second push-button at the lower right (27).
Programming mode is activated. The operation LED (26) flashes quickly (approx. 8 Hz).
i Use suitable objects to push the buttons (e.g. thin screwdriver, tip of a ballpoint pen, etc.)
i To exclude any inadvertent activation of Programming mode during a 'normal' use of the
control surface in later operation, the time between the first and the second button
actuation must be at least 200 ms. Pressing both buttons simultaneously (time between
first and second actuation < 200 ms) will not result in an activation of Programming mode.
i In programming mode, the operation LED flashes steadily in the colour blue. The flashing
rate remains the same until the operating mode is ended. The state of the LED defined by
Programming mode will always prevail.
o Program the physical address with the help of the ETS.
o Programming mode ends:
- Automatically after adoption of the physical address
- By pressing a button
Page 9 of 39

Installation, electrical connection and operation

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
i If Programming mode is to be activated or deactivated in a device which is already
programmed with a valid application, there is the possibility that telegrams will be
transmitted to the bus at the time the button is pressed. The telegram transmitted depends
on the button function programmed.
Programming the application program
Program the application into the device with the help of the ETS. For commissioning it is
recommended to use the ETS4 or ETS3.0 from Version "d" onwards.
The ETS detects automatically whether a valid application has already been programmed into
the device before. To reduce the programming time, the ETS downloads the whole application
only if the device was programmed beforehand with another application or with no application at
all. In all other cases, the ETS makes a time-optimised partial download in which only the
modified data is loaded into the device.
Installing the decorative control surfaces
The decorative control surfaces are available as a complete set of buttons. Individual buttons or
the complete set of buttons can be replaced using buttons with icons.
The decorative control surfaces are not included in the scope of delivery of the push button
sensor module. These must be ordered specially according to the required design.
o Place control surfaces on the pushbutton sensor module in the right orientation and snap in
with a short push.
Page 10 of 39

Installation, electrical connection and operation

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
2.5 Operation
Control surfaces
The standard pushbutton sensor modules consist of several control surfaces. The operation
concept can be configured in the ETS either as a rocker function or alternatively as a push
button function (only "Switching" function). With the rocker function, two neighbouring control
surfaces are combined into one rocker switch. In the pushbutton function, each control surface
is evaluated as single-surface operation.
The number of control surfaces depends on the push-button sensor used.
The Standard push-button modules have one red status LED for each rocker switch. The status
LEDs can be switched on or off permanently, or can function as a status indicator. As an
alternative, with the aid of separate communication objects, they can signal widely varying
display information completely independently of the push-button function, e.g. operation states
of lighting systems or room temperature controllers.
The operation LED can also signal the switching state of its own object, flash or be permanently
on or off. Besides functions that can be set using the ETS, the operation LED also indicates that
the push button sensor is in the programming mode for commissioning or diagnosis purposes.
i Configuration of the control surfaces (button or rocker function) is described in detail in the
chapter "Software description"
Page 11 of 39

Installation, electrical connection and operation

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
3 Technical data
General
Protection class III
Mark of approval KNX/EIB
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
KNX/EIB supply
KNX medium TP 1
Commissioning mode S-mode
Rated voltage KNX DC 21 ... 32 V SELV
Power consumption KNX max. 150 mW
Connection mode KNX Connection terminal
Page 12 of 39

Technical data

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
4 Software description
4.1 Software specification
ETS search paths: Push-button / Push-button, 1-gang / Standard push-button
module, 1-gang
Push-button / Push-button, 2-gang / Standard push-button
module, 2-gang
Push-button / Push-button, 3-gang / Standard push-button
module, 3-gang
Push-button / Push-button, 4-gang / Standard push-button
module, 4-gang
Configuration: S-mode standard
PEI type: "00"Hex / "0" Dec
PEI connector: no connector
Application for standard pushbutton sensor module, 1-gang:
No. Short description Name Version from mask
version
1 Standard push button sensor
application:
Two control surfaces, alternatively as a
rocker or push-button function (only
switching possible with push-button
function).
Standard TSM
110A11
1.1
for ETS3.0
Version d
onwards
and ETS4
705
Application for standard pushbutton sensor module, 2-gang:
No. Short description Name Version from mask
version
1 Standard push button sensor
application:
Four control surfaces, alternatively as a
rocker or push-button function (only
switching possible with push-button
function).
Standard TSM
110B11
1.1
for ETS3.0
Version d
onwards
and ETS4
705
Page 13 of 39

Software specification

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
Application for standard pushbutton sensor module, 3-gang:
No. Short description Name Version from mask
version
1 Standard push button sensor
application:
Six control surfaces, alternatively as a
rocker or push-button function (only
switching possible with push-button
function).
Standard TSM
110C11
1.1
for ETS3.0
Version d
onwards
and ETS4
705
Application for standard pushbutton sensor module, 4-gang:
No. Short description Name Version from mask
version
1 Standard push button sensor
application:
Eight control surfaces, alternatively as
a rocker or push-button function (only
switching possible with push-button
function).
Standard TSM
110D11
1.1
for ETS3.0
Version d
onwards
and ETS4
705
Page 14 of 39

Software specification

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
4.2 Software "Standard TSM 110x11"
4.2.1 Scope of functions
Scope of functions
- Each control surface can be used as independent button or – when linked with the opposite
button – as a rocker function.
- Each rocker can be used for the functions 'switching', 'dimming', 'blind/shutter', '1-byte
value transmitter' and 'scene extension'.
- Each button can be used for the switching functions.
- The switching function permits the following settings: reaction after pressing and/or
releasing, switch on, switch off, and toggle.
- Dimming permits the following settings: times for short and long presses.
- The shutter control permits the following settings: command on pressing (up, down,
TOGGLE), setting of times for short and long press and slat adjustment.
- The 1-byte value transmitter function permits the following settings: selection of the value
range (0 … 100 %, 0 … 255), value on pressing.
- Scene control permits the following settings: calling up or saving of external scenes using a
settable scene number (1...64).
- Each rocker has one status LED of its own available. The Status LEDs are configured
independently of one another and can be switched on permanently, for orientation
purposes, or controlled for switching via a 1-bit communication object. The status LEDs can
also function as an operation indication as an option.
- The operation LED can be switched permanently on or off. When the operation LED is
used, its colour can be configured in the ETS (red, green, blue).
- To save energy, an energy-saving mode can be activated. If the energy-saving mode is
used, the signalling function of the device is switched off after a preset time without
operation or by an external telegram. The energy saving mode can be deactivated by an
operation or by a special telegram. Afterwards, the device is fully functional again.
Page 15 of 39
Software "Standard TSM 110x11"
Scope of functions

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
4.2.2 Notes on software
ETS configuration and commissioning
Configuration and commissioning of the device with the following ETS versions...
- ETS3.0 Version d or higher
- ETS4.0.7 or higher
The necessary product database is offered in the *.VD4 format. No product database is
available for ETS2 and older versions of ETS3.
Page 16 of 39
Software "Standard TSM 110x11"
Notes on software

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
4.2.3 Object table
Number of communication objects: max. 17 objects (4-gang variant)
Number of addresses (max): 254
Number of assignments (max): 255
4.2.3.1 Objects for rocker or button functions
Objects for rocker or button function:
Function: Switching
Object
h0,
1, ...
7
Function
Switching
Name
Rocker/button 1 1,2
Type
1-bit
DPT
1.xxx
Flag
C, W, T,
(R) 3
Description 1-bit object for transmission of switching telegrams (ON, OFF).
Function: Dimming
Object
h0, 2,
4, 6
Function
Switching
Name
Rocker 1 1,2
Type
1-bit
DPT
1.xxx
Flag
C, W, T,
(R) 3
Description 1-bit object for the transmission of switching telegrams (ON, OFF) for the
dimming function.
Function: Dimming
Object
h18,
20,
22,
24
Function
Dimming
Name
Rocker 1 1,2
Type
4-bit
DPT
3.007
Flag
C, W, T,
(R) 3
Description 4-bit object for the transmission of relative dimming telegrams.
1: The number of rockers or buttons depends on the planned device variant.
2: The objects have been described for rocker 1 or button 1 as an example. The objects for the
other rockers/buttons are defined in the same way by shifting the object number and changing
the object name.
3: For reading, the R-flag must be set. The last value written to the object via the bus will be
read.
Page 17 of 39
Software "Standard TSM 110x11"
Object table

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
Function: Venetian blind
Object
h0, 2,
4, 6
Function
Short time operation
Name
Rocker 1 1,2
Type
1-bit
DPT
1.007
Flag
C, -, T, (R)
3
Description 1-bit object for the transmission of telegrams with which a Venetian blind or
shutter drive motor can be stopped or with which the blind slats can be
adjusted by short time operation.
Function: Venetian blind
Object
h18,
20,
22,
24
Function
Long-time operation
Name
Rocker 1 1,2
Type
1-bit
DPT
1.008
Flag
C, W, T,
(R) 3
Description 1-bit object for the transmission of telegrams with which a Venetian blind or
shutter drive motor can be can be moved upwards or downwards.
Function: 1-byte value transmitter
Object
h0, 2,
4, 6
Function
Value
Name
Rocker 1 1,2
Type
1 byte
DPT
5.xxx
Flag
C, W, T,
(R) 3
Description 1-byte object for the transmission of values from 0 to 255 (corresponding to
values from 0 % to 100 %).
Function: Scene extension
Object
h0, 2,
4, 6
Function
Scene extension
Name
Rocker 1 1,2
Type
1 byte
DPT
18.001
Flag
C, -, T, (R)
3
Description 1-byte object for recalling or for storing one of 64 external scenes max.
1: The number of rockers or buttons depends on the planned device variant.
2: The objects have been described for rocker 1 or button 1 as an example. The objects for the
other rockers/buttons are defined in the same way by shifting the object number and changing
the object name.
3: For reading, the R-flag must be set. The last value written to the object via the bus will be
read.
Page 18 of 39
Software "Standard TSM 110x11"
Object table

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
4.2.3.2 Objects for status LED
Objects for status LED:
Function: Status LED (control via separate LED object)
Object
h36,
38,
40,
42
Function
Switching
Name
Status LED 1 1
Type
1-bit
DPT
1.xxx
Flag
C, W, -, (R)
2
Description 1-bit object for activation of the status LED.
1: The objects have been described for status LED 1 as an example. The objects for the other
status LED are defined in the same way by shifting the object number and changing the object
name.
2: For reading, the R-flag must be set. The last value written to the object via the bus will be
read.
Page 19 of 39
Software "Standard TSM 110x11"
Object table

Art. No. 5071 TSM
Art. No. 5072 TSM
Art. No. 5073 TSM
Art. No. 5074 TSM
4.2.3.3 Object for energy saving mode
Object for energy saving mode:
Function: Energy saving mode
Object
h154
Function
Activate / deactivate
Name
Energy saving
mode
Type
1-bit
DPT
1.001
Flag
C, W, -, (R)
1
Description 1-bit object for activating or deactivating the energy saving mode.
The function (only activate, only deactivate, activate and deactivate) and the
telegram polarity are configurable.
If the transmission flag is set, then other devices can be informed of the
deactivation of energy-saving mode through operation on the local device,
causing them also to leave energy-saving mode (precondition: all the devices
are linked to the same group address and the deactivation via an object must
be possible in the parameterisation of the other devices). When energy-saving
mode is deactivated when the transmission flag is set, the device sends an
"Energy-saving mode deactivated" telegram to the bus, according to the
inverted activated telegram polarity.
1: For reading, the R-flag must be set. The last value written to the object via the bus will be
read.
Page 20 of 39
Software "Standard TSM 110x11"
Object table