Jung KNX RF Series User manual

KNX RF radio transmitter module
KNX RF radio transmitter module 1-gang
Art. No. : 4071 RF TSM
KNX RF radio transmitter module 2-gang
Art. No. : 4072 RF TSM
KNX RF radio transmitter module 3-gang
Art. No. : 4073 RF TSM
KNX RF radio transmitter module 4-gang
Art. No. : 4074 RF TSM
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Keep button cells out of reach of children! If button cells are swallowed, get medical help
immediately.
Risk of explosion! Do not throw batteries into fire.
Risk of explosion! Do not recharge batteries.
The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1: 4-gang radio pushbutton module
(1) Base plate
(2) Fastening screws for the base plate
(3) Design frame
(4) Pushbutton module with adapter frame (see adapter frame assembly instructions)
(5) Fastening screws
(6) Buttons
1/6
32591013
j0082591013 18.01.2016

Figure 2: Pushbutton assignment 1-gang, 2-gang, 3-gang and 4-gang
(7) Acknowledgement/transmission LED, blue
(8) Status LED per button pair, red
3 Function
System information
This device is a product of the KNX system and complies with the KNX directives. Detailed
technical knowledge obtained in KNX training courses is a prerequisite to proper understanding.
The range of a radio system depends on various external circumstances. The range can be
optimised by the choice of installation location. The product documentation for this device
contains application basics for the KNX radio system.
This device meets the requirements of the R&TTE directive 1999/5/EC and may be operated in
all EU and EFTA countries.
The function of this device depends upon the software. Detailed information on loadable
software and attainable functionality as well as the software itself can be obtained from the
manufacturer´s product database. Planning, installation and commissioning of the device are
carried out with the aid of KNX-certified software of version ETS5 or higher. You can find the
up-to-date product database, technical descriptions and declaration of conformity on our
website.
Intended use
- Radio operation of loads, e.g. light on/off, dimming, Venetian blinds up/down, brightness
values, calling up and saving light scenes.
- Operation in cabled KNX systems via media coupler (see chapter Accessories)
Product characteristics
- Pushbutton functions switching, dimming, Venetian blind control, value transmitter, scene
recall
- One, two, three or four button pairs for pushbutton function or rocker function
- Status indicator via status LED
- Battery-powered device
Energy saving mode
The device switches to the energy saving mode after a preset time. In energy saving mode, the
LEDs remains switched off. During operation, the energy saving mode is exited.
iOperations from the energy saving mode are executed immediately.
2/6
32591013
j0082591013 18.01.2016
KNX RF radio transmitter module

4 Operation
Operating a function or load
oSwitch: Short press on button.
oDim: Long press on the button.
oMove Venetian blind: Long press on button.
oStop or adjust Venetian blind: Short press on button.
oCall up light scene: Short press on button.
oSave light scene: Press button for longer than 5 seconds.
oSet value: Press button briefly.
LED function
Acknowledgement/transmission LED (7) lights up after pressing a button and goes out as soon
as the feedback has been received from the actuator. After the acknowledgement/transmission
LED goes out, the status LED (8) displays the actuator feedback. The display duration can be
changed by the programming or can be dispensed with entirely.
The acknowledgement/transmission LED flashes rapidly if a transmission error occurs.
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
Fitting the device
To ensure good transmission quality, keep a sufficient distance from any possible sources of
interference, e.g. metallic surfaces, microwave ovens, hi-fi and TV systems, ballasts or
transformers.
iPerform commissioning procedures before installation (see chapter Commissioning).
oChange the battery (see chapter Changing the battery).
oScrew or glue the base plate (1) to an even surface. The TOP/OBEN label has to be at the
top.
oAttach design-frame (3) to the base plate.
oScrew wall transmitter module (4) to base plate.
iScrewing the screws too tightly could impair functions of the wall transmitter.
oSnap covers (6) on (figure 1).
Information on gluing mounting
To be able to fasten the pushbutton safely, the substrate must be flat and free of dust and
grease.
oRemove the rear, unpunched film of the enclosed adhesive pad.
oAlign the adhesive pad, stick it to the surface and smooth it out. Remove air bubbles.
oRemove the two inner segments of the front film.
oAlign the base plate to the external punching and stick it on.
iIn the case of multiple combinations, the abutting sides of the adhesive pads must be cut
along the external punching using a ruler and a cutter (figure 3).
3/6
32591013
j0082591013 18.01.2016
KNX RF radio transmitter module

Figure 3: Cutting the adhesive pads for multiple combinations
iIf necessary, after mounting the wall transmitter in the CD program, carefully remove the
excess adhesive film in the corners.
5.2 Commissioning
Insert battery
WARNING!
Risk of chemical burns.
Batteries can burst and leak.
Replace batteries only with an identical or equivalent type.
oCarefully remove buttons (6) from the pushbutton sensor (figure 1).
oUnscrew pushbutton from the base plate (1).
iKeep contacts of batteries and device free of grease.
oApply battery to the positive contact of the battery holder. Observe polarity: the positive
pole of the battery must be at the top.
oPress gently on battery to snap it in.
oMount pushbutton onto the base plate and snap covers on.
The pushbutton is ready for operation.
Loading the physical address and application software
Project design and commissioning with ETS5 or a more recent version.
The device is connected and ready for operation.
The buttons are not mounted yet.
iIf the device does not contain any application software, or contains the wrong application
software, then the acknowledgement/transmission LED flashes slowly for
approx. 3 seconds.
4/6
32591013
j0082591013 18.01.2016
KNX RF radio transmitter module

Figure 4: Activating programming mode
oActivate programming mode: Press and hold push-button at the upper left (9). Then press
push-button at the lower right (10).
The acknowledgement/transmission LED (7) flashes rapidly.
oLoad the physical address and domain address into the device.
The acknowledgement/transmission LED (7) returns to its previous state – off, on, or
flashing slowly.
oWrite the physical address and domain address on the device label.
oLoad the application software into the device.
iBefore updating the system software or before a later correction of the programming,
replace a battery with a new, unused battery.
Installing the buttons
The buttons are available as a complete set of buttons. Individual buttons or the complete set of
buttons can be replaced using buttons with icons.
iThe mounting spider is not required to mount the buttons.
The physical address and domain address are loaded into the device.
oPlace the buttons on the device in the correct orientation and snap in with a short push.
Note the marking.
6 Appendix
Remove empty batteries immediately and dispose of in an environmentally friendly
manner. Do not throw batteries into household waste. Consult your local authorities
about environmentally friendly disposal. According to statutory provisions, the end
consumer is obligated to return used batteries.
The icon confirms the conformity of the product to the relevant guidelines.
6.1 Technical data
KNX medium RF1.R
Commissioning mode S-mode
Rated voltage DC 3V
Battery type 1×Lithium CR 2450N
Ambient temperature -5 ... +45°C
Degree of protection IP 20
Radio frequency 868.3MHz
Transmitting power max. 20mW
Transmitting range in free field typ. 100m
5/6
32591013
j0082591013 18.01.2016
KNX RF radio transmitter module

6.2 Troubleshooting
After a button has been pressed, the acknowledgement/transmission LED (7) flashes
slowly for 3 seconds.
Cause: Battery in the pushbutton is almost empty.
Change the battery (see chapter Commissioning - Inserting the battery).
Receiver does not respond, acknowledgement/transmission LED flashes rapidly for
3 seconds.
Cause: The pushbutton could not send the telegram, e.g. due to a missing group address.
Correct the programming.
Receiver does not react, actuator feedback is not displayed.
Cause 1: Radio range exceeded. Structural obstacles reduce the range.
Use of the media coupler as a radio repeater.
Cause 2: Receiver or media coupler is not ready for operation.
Check the receiver, mains voltage or media coupler.
Cause 3: There are radio faults, e.g. through outside radio.
Eliminate radio interference.
6.3 Accessories
Cover kit 1-gang, complete Art. No. ..401 TSA..
Cover kit 2-gang, complete Art. No. ..402 TSA..
Cover kit 3-gang, complete Art. No. ..403 TSA..
Cover kit 4-gang, complete Art. No. ..404 TSA..
KNX RF radio converter Art. No. MK100RF
KNX RF radio USB stick Art. No. USB2130RF
6.4 Warranty
The warranty follows about the specialty store in between the legal framework as provided for
by law
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: [phone]
Telefax: [phone]
[email protected]
www.jung.de
6/6
32591013
j0082591013 18.01.2016
KNX RF radio transmitter module