Jung 4074 TSM Operator's manual

Product documentation
Standard push-button module with BCU, 4-gang
Art.-No.: 4074 TSM
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
D-58579 Schalksmühle
Telefon: +49.23 55.8 06-0
Telefax: +49.23 55.8 06-1 89
E-mail: [email protected]
Internet: www.jung.de
www.jung-katalog.de Issue: 02.09.2008

Art.-No.: 4074 TSM
Content
1 Product definition 3 ................................................................................................................
1.1 Product catalogue 3 ...........................................................................................................
1.2 Function 3 ..........................................................................................................................
2 Installation, electrical connection and operation 4 .............................................................
2.1 Safety instructions 4 ..........................................................................................................
2.2 Device components 5 ........................................................................................................
2.3 Fitting and electrical connection 6 .....................................................................................
2.4 Commissioning 8 ...............................................................................................................
2.5 Operation 10 ......................................................................................................................
3 Technical data 11 ....................................................................................................................
4 Software description 12 .........................................................................................................
4.1 Software specification 12 ...................................................................................................
4.2 Software "Switching 109Bx1" 13 .......................................................................................
4.2.1 Scope of functions 13 .................................................................................................
4.2.2 Object table 14 ...........................................................................................................
4.2.3 Parameters 16 ............................................................................................................
4.3 Software "Dimming 109Bx2" 18 ........................................................................................
4.3.1 Scope of functions 18 .................................................................................................
4.3.2 Object table 19 ...........................................................................................................
4.3.3 Parameters 21 ............................................................................................................
4.4 Software "Blind 109Bx3" 22 ...............................................................................................
4.4.1 Scope of functions 22 .................................................................................................
4.4.2 Object table 23 ...........................................................................................................
4.4.3 Parameters 25 ............................................................................................................
4.5 Software "Value transmitter, scene extension 109Bx4" 26 ...............................................
4.5.1 Scope of functions 26 .................................................................................................
4.5.2 Object table 27 ...........................................................................................................
4.5.3 Parameters 29 ............................................................................................................
5 Appendix 31 .............................................................................................................................
5.1 Index 31 .............................................................................................................................
Product documentation
Page 2 of 32

Art.-No.: 4074 TSM
1 Product definition
1.1 Product catalogue
Product name: Standard push-button module, 4-gang
Use: Sensor
Design: UP (flush-mounting type)
Art.-No.: 4074 TSM
1.2 Function
When a button is pressed, and depending on the loaded application and the parameters pro-
grammed, the push button sensor Standard TSM transmits telegrams to the KNX / EIB. These
can be, for instance, telegrams for switching or momentary-contact control, for dimming or for
shutter control. It is also possible to program value transmitter functions such as dimming value
transmitters or light scene extensions.
The 4x Standard TSM push button sensor consists of four control surfaces. In the "Switching"
application of the ETS, the control concept of one control surface can be configured as a rocker
function or as a button function. The control concept is defined as a rocker in the "Dimming",
"Blind" and "Value transmitter, scene extension" applications. With the rocker function, one con-
trol surface is divided into two actuation pressure points with the same basic function. With the
button function, one control surface is evaluated as two functionally-different actuation pressure
points (two buttons).
The Standard TSM push button sensor is equipped with one status LED per control surface.
One status LED can optionally either be permanently on or off, or otherwise act as a button-
press actuation or status indicator for a button or a rocker.
If necessary, an operation LED can optionally serve as an orientation light. If the push button is
in Programming mode, the operation LED flashes with a frequency of about 8 Hz. If there is no
(suitable) application loaded in the push button, the operation LED flashes to indicate an error at
a frequency of approx. 0.75 Hz and the push button sensor does not work.
A BCU is already permanently integrated in the Standard TSM push button sensor, allowing the
device to be connected directly to the bus cable during commissioning.
Page 3 of 32

Product definition

Art.-No.: 4074 TSM
2 Installation, electrical connection and operation
2.1 Safety instructions
Electrical equipment must be installed and fitted by qualified electricians. The applicable
accident prevention regulations must be observed.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
During installation, adequate insulation between the mains voltage and the bus must be
ensured! A minimum distance of at least 4 mm must be maintained between bus con-
ductors and mains voltage cores.
The device may not be opened or operated outside the technical specifications.
Page 4 of 32

Installation, electrical connection and operation

Art.-No.: 4074 TSM
2.2 Device components
Device components of the 4x Standard TSM push button sensor
picture 1: Device arrangement of the 4x Standard TSM push button sensor
(1) 2 control surfaces configurable as a rocker 1...4 or as buttons 1…8 (buttons only for
"Switching" application).
(2) 4 status LEDs (red)
(3) 1 operation LED (blue)
Dimensions of the Standard TSM push button sensor:
Width (W): 55 mm / Height (H): 55 mm / Depth (D): 20 mm
Dimensions without decorative frame and covers, without supporting plate.
Page 5 of 32

Installation, electrical connection and operation

Art.-No.: 4074 TSM
2.3 Fitting and electrical connection
DANGER!
Electrical shock on contact with live parts in the fitting environment.
Electrical shocks can be fatal.
Before working on the device, disconnect the supply voltage and cover up live
parts in the working environment.
DANGER!
Danger of electrical shock!
When installing with 230 V socket outlets under a common cover there is a
danger of electrical shocks in the event of a fault!
Use only the supplied plastic screws for fixing to the supporting ring.
Snapping on the adapter frame
An adapter frame is required for the CD design. The adapter frame must be snapped onto the
push button sensor module, before the push button sensor is connected and fastened to the
wall.
o With the adapter frame (6) in the right orientation, snap it from the front onto the push but-
ton module (7) (see chapter 2.4. Commissioning). Note marking TOP = top/front.
Installing the push button sensor and connecting it
picture 2: Installation of the push button sensor
(4) Supporting ring
(5) Decorative frame
(6) Adapter frame (only for the CD design)
(7) Push button module
(8) Fastening screws
Page 6 of 32

Installation, electrical connection and operation

Art.-No.: 4074 TSM
(9) Decorative control surfaces
(10) KNX connection terminal
i The installation of the support ring depends on the design used.
Supporting ring side "A" from the front for switch design range "FD-Design" (frame height 6
mm).
Supporting ring side "B" from the front for switch design range "CD-Design" and "A-Design"
(frame height 11 mm).
o Mount supporting ring (4) in the right orientation on an appliance box. Note marking TOP;
marking "A" or "B" in front. Use the supplied box screws.
o Position the decorative frame (5) on the supporting ring.
o Connect the push button module (7) with KNW connection terminal (10), which is connec-
ted to the KNX bus cable, to the rear side of the module. Run the connection cable down-
wards from the push button module and then into the accessory socket from the rear.
o Push the push button module (7) onto the supporting ring (4).
o Fasten the push button module (7) to supporting ring using the supplied plastic screws (8).
Tighten the plastic screws only lightly.
o Before mounting the control surfaces (9), load the physical address into the device (see
chapter 2.4. Commissioning).
Page 7 of 32

Installation, electrical connection and operation

Art.-No.: 4074 TSM
2.4 Commissioning
After connecting the standard push button sensor TSM to the bus and mounting it on the wall, it
can be put into operation. The start-up procedure is basically confined to programming with the
ETS and attaching the decorative operating areas.
Assignment of the physical address
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before working on the device, disconnect the supply voltage and cover up live
parts in the working environment.
The standard push button sensor TSM is equipped with an integrated BCU. The push button
sensor has no separate programming key or LED. Programming mode is activated by a defined
and time-delayed press on the first rocker and signalled by the operation LED. To program the
physical address, the design operating areas must not be in placed on the device.
The physical address is programmed as described below...
picture 3: Buttons for activating Programming mode
o Activate Programming mode. Press button at the top left (11) and keep it depressed (see
picture 3). Then push the second button of rocker 1 at the bottom right (12).
Programming mode is activated. The operation LED (12) flashes quickly (approx. 8 Hz).
i Use suitable objects to push the buttons (e.g. thin screwdriver, tip of a ballpoint pen, etc.)
i To exclude any inadvertent activation of Programming mode during a 'normal' use of the
control surface in later operation, the time between the first and the second button actu-
ation must be at least 200 ms. Pressing both buttons simultaneously (time between first
and second actuation < 200 ms) will not result in an activation of Programming mode.
i In Programming mode, the flashing rate remains the same until the mode is ended. The
state of the LED defined by Programming mode will always prevail.
o Program the physical address with the help of the ETS.
o Programming mode ends:
- Automatically after adoption of the physical address
- By pressing a button
i If Programming mode is to be activated or deactivated in a device which is already pro-
grammed with a valid application, there is the possibility that telegrams will be transmitted
to the bus at the time the button is pressed. The telegram transmitted depends on the but-
ton function programmed.
Page 8 of 32

Installation, electrical connection and operation

Art.-No.: 4074 TSM
Programming the application
Program the application into the device with the help of the ETS. The ETS3.0 from version "d"
onwards detects automatically whether a valid application has already been programmed into
the device before. To reduce the programming time, the ETS3 downloads the whole application
only if the device was programmed beforehand with another application or with no application at
all. In all other cases, the ETS makes a time-optimised partial download in which only the modi-
fied data is loaded into the device.
Depending on the programming command, the ETS2 programs the application for the push but-
ton sensor either completely or partially for parameters and group addresses. The time-optim-
ised download procedure of the ETS3.0d is not available in this version.
For start-up purposes, it is recommended to use the ETS3.0 from version "d" onwards.
Installing the decorative control surfaces
The decorative control surfaces are available as a complete set of buttons. Individual buttons or
the complete set of buttons can be replaced using buttons with symbols.
The decorative control surfaces are not included in the scope of delivery of the push button
sensor. These must be ordered specially according to the required design.
The physical address of the push button sensor must be programmed in the device in advance.
o Place control surfaces on the push button sensor in the right orientation and snap in with a
short push. Note marking TOP.
i To simplify installation, a complete set of buttons is fitted with a mounting spider at the fact-
ory. This mounting spider is not essential for installing the decorative control surfaces,
meaning that it is not required when adding symbol buttons to the button panel.
Page 9 of 32

Installation, electrical connection and operation

Art.-No.: 4074 TSM
2.5 Operation
Control surfaces
The 4x Standard TSM push button sensor consists of four control surfaces. In the "Switching"
application of the ETS, the control concept of one control surface can be configured as a rocker
function or as a button function. The control concept is defined as a rocker in the "Dimming",
"Blind" and "Value transmitter, scene extension" applications. With the rocker function, one con-
trol surface is divided into two actuation pressure points with the same basic function. With the
button function, the control surface is evaluated in two functionally-different actuation pressure
points (two buttons).
The buttons are always arranged "vertically" on a control surface (pressure points at top and
bottom).
Next to each control surface, there is a red LED, which can be connected to the control function,
according to the function of the rocker or buttons. However, it can also be switched permanently
on or off.
The operation LED of the push button sensor can be switched permanently on or off. Besides
functions programmed in the ETS, the operation LED also indicates that the push button sensor
is in Programming mode for commissioning or diagnosis purposes.
Page 10 of 32

Installation, electrical connection and operation

Art.-No.: 4074 TSM
3 Technical data

Technical data
General
Protection class IP 20
Safety class III
Mark of approval KNX
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
KNX / EIB supply
KNX medium TP 1
Commissioning mode S mode
Rated voltage KNX DC 21 V ... 32 V SELV
Power consumption KNX typ. 150 mW
Connection mode KNX Terminal
Page 11 of 32

Technical data

Art.-No.: 4074 TSM
4 Software description
4.1 Software specification
ETS search paths: Push-button / Push-button, 4-gang / Standard push-button mod-
ule, 4-gang
BAU used: ASIC FZE 1065 + µC
KNX/EIB type class: 3b device with cert. physical layer + stack
Configuration: S-mode standard
PEI type: "00"Hex / "0" Dec
PEI connection: No connector
Applications:
No. Short description Name Version from screen
version
1 Touch sensor application to send
switching telegrams.
Switching 109B01
Switching 109B11
0.1
for ETS 2
and ETS
3.0a…c
1.1
from ETS 3
from
Version d
705
705
2 Touch sensor application to send dim-
ming telegrams.
Dimming 109B02
Dimming 109B12
0.2
for ETS 2
and ETS
3.0a…c
1.2
from ETS 3
from
Version d
705
705
3 Touch sensor application to send blind
telegrams.
Blind 109B03
Blind 109B13
0.3
for ETS 2
and ETS
3.0a…c
1.3
from ETS 3
from
Version d
705
705
4 Touch sensor application to send value
or scene telegrams.
Value transmitter,
scene extension
109B04
Value transmitter,
scene extension
109B14
0.4
for ETS 2
and ETS
3.0a…c
1.4
from ETS 3
from
Version d
705
705
Page 12 of 32

Software specification

Art.-No.: 4074 TSM
4.2 Software "Switching 109Bx1"
4.2.1 Scope of functions
Scope of functions
- Function of operation LED and status LED configurable
- Rocker or button function.
- Command on actuating the buttons configurable (ON, OFF, TOGGLE).
Page 13 of 32
Software "Switching 109Bx1"
Scope of functions

Art.-No.: 4074 TSM
4.2.2 Object table
Number of communication objects: 8
Number of addresses (max): 100
Number of assignments (max): 100
Dynamic table management: No
Maximum table length: ---
Objects for rocker function:
Function: Switching
Object
h0
Function
Switching
Name
Rocker 1
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h2
Function
Switching
Name
Rocker 2
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h4
Function
Switching
Name
Rocker 3
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h6
Function
Switching
Name
Rocker 4
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Objects for button function:
Function: Switching
Object
h0
Function
Switching
Name
Button 1
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Page 14 of 32
Software "Switching 109Bx1"
Object table

Art.-No.: 4074 TSM
Function: Switching
Object
h1
Function
Switching
Name
Button 2
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h2
Function
Switching
Name
Button 3
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h3
Function
Switching
Name
Button 4
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h4
Function
Switching
Name
Button 5
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h5
Function
Switching
Name
Button 6
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h6
Function
Switching
Name
Button 7
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h7
Function
Switching
Name
Button 8
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Page 15 of 32
Software "Switching 109Bx1"
Object table

Art.-No.: 4074 TSM
4.2.3 Parameters
Description Values Comment
h General
Light period of status
LED for button-press in-
dicator
1 s
2 s
3 s
4 s
5 s
This parameter defines the time the
status LED is lit up to indicate actuation.
The setting concerns all status LEDs
whose function is set to "Actuation indic-
ator".
Function of operation
LED
Always OFF
Always ON
Specifies the state of the operation LED.
h Rocker 1
Function No function
Switching
This parameter is used to define the ba-
sic function of the rocker.
i "No function" = Rocker 1 deactiv-
ated.
Rocker or button Button
Rocker
Here, you can specify whether the rock-
er is to be used with a common basic
function or as two different buttons with
independent objects.
Depending on this choice, the ETS dis-
plays different communication objects
and parameters.
Function of status LED Always OFF
Always ON
Button-press indicator
Status display
(of the switching object)
Inverted status display
(of the switching display)
Specifies the control of the status LED.
i Only with rocker function.
Function of status LED Always OFF
Always ON
Button-press indicator
Status display
(of the switching object 0)
Inverted status display
(of the switching display 0)
Status display
(of the switching object 1)
Inverted status display
(of the switching display 1)
Specifies the control of the status LED.
i Only for button function.
Page 16 of 32
Software "Switching 109Bx1"
Parameters

Art.-No.: 4074 TSM
Command on pressing
the top rocker
No function
ON
OFF
TOGGLE
Defines the command when the rocker
button is pressed at the top.
i Only with rocker function.
Command on pressing
the bottom rocker
No function
ON
OFF
TOGGLE
Defines the command when the rocker
button is pressed at the bottom.
i Only for button function.
Command on pressing
the top button
No function
ON
OFF
TOGGLE
Defines the command on pressing the
top button.
i Only for button function.
Command on releasing
the top button
No function
ON
OFF
TOGGLE
Defines the command on releasing the
top button.
i Only for button function.
Command on pressing
the bottom button
No function
ON
OFF
TOGGLE
Defines the command on pressing the
bottom button.
i Only for button function.
Command on releasing
the bottom button
No function
ON
OFF
TOGGLE
Defines the command on releasing the
bottom button.
i Only for button function.
h For rocker 2...4 see rocker 1.
Page 17 of 32
Software "Switching 109Bx1"
Parameters

Art.-No.: 4074 TSM
4.3 Software "Dimming 109Bx2"
4.3.1 Scope of functions
Scope of functions
- Function of operation LED and status LED configurable
- Rocker function
- Command on actuating the rocker configurable (lighter - ON, darker - OFF).
- Time between switching and dimming can be set.
Page 18 of 32
Software "Dimming 109Bx2"
Scope of functions

Art.-No.: 4074 TSM
4.3.2 Object table
Number of communication objects: 8
Number of addresses (max): 100
Number of assignments (max): 100
Dynamic table management: No
Maximum table length: ---
Function: Switching
Object
h0
Function
Switching
Name
Rocker 1
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h2
Function
Switching
Name
Rocker 2
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h4
Function
Switching
Name
Rocker 3
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Switching
Object
h6
Function
Switching
Name
Rocker 4
Type
1 bit
DP type
1.xxx
Flag
C, W, T
Description 1-bit object for the transmission of switching telegrams (ON, OFF).
Function: Dimming
Object
h8
Function
Dimming
Name
Rocker 1
Type
4 bit
DP type
3.007
Flag
C, W, T
Description 4-bit object for relative brightness adjustment between 0% and 100 %.
Function: Dimming
Object
h10
Function
Dimming
Name
Rocker 2
Type
4 bit
DP type
3.007
Flag
C, W, T
Description 4-bit object for relative brightness adjustment between 0% and 100 %.
Page 19 of 32
Software "Dimming 109Bx2"
Object table

Art.-No.: 4074 TSM
Function: Dimming
Object
h12
Function
Dimming
Name
Rocker 3
Type
4 bit
DP type
3.007
Flag
C, W, T
Description 4-bit object for relative brightness adjustment between 0% and 100 %.
Function: Dimming
Object
h14
Function
Dimming
Name
Rocker 4
Type
4 bit
DP type
3.007
Flag
C, W, T
Description 4-bit object for relative brightness adjustment between 0% and 100 %.
Page 20 of 32
Software "Dimming 109Bx2"
Object table