Jung TK SV STG 60 REG User manual

1
Product Information
DCM Power supply and control unit 60 mA
TK SV STG 60 REG
Safety instructions
!Assembly, installation, and commissioning must only be carried out by a qualified
electrician!
For work on systems with 230 V AC mains current the safety requirements of DIN VDE
0100 must be observed.
When installing DCM BUS systems the general safety rules for telecommunication sys-
tems in accordance with VDE 0800 must be observed:
•separate cabling for high and low voltage lines
•minimum distance of 10 cm for joint cabling arrangements,
•use of separators between high and low voltage lines in joint cable ducts,
•use of standard telecommunication cables, e. g. J-Y (St) Y with 0.8 mm² cross section
!Suitable lightning prediction must ensure that a voltage of 32 V DC will not be
exceeded at the DCM BUS wires a and b.
DCM = Door Communication Management

2
Application / Brief description
Application
•power supply and control unit for door communication systems
•light switching with floating relay contact
•power supply for door release
Brief description
•power supply for DCM BUS, short circuit protected
•switching between operation and programming mode
•status/programming LED
•floating relay contact for light switching (make contact, 24 V DC / 1 A)
•light switching time adjustable
•internal door release relay with power supply AC 12 V
•door release time from 0.8 s up to 8 s manually adjustable
•light switching function
•for rail mounting installation into distribution boards according to DIN EN 50022
Device overview
Potentiometer
Door release time
Potentiometer
li
g
ht switchin
g
time
Run/Pro
g
button
Run/Prog LED
Power supply input AC 230 V~
Connection for door
release 12 V Connection DCM-BUS
Connection light switching

3
Wiring and installation
Wiring example (with TK SV 2500 REG)
Attention!
Do NOT connect terminal 29 (+) of TK SV 2500 REG
with terminal 25 (P) of power supply & control unit.
3-wire technique
Please observe cable length and loop resistance.
Floor bell button
Floor bell button
Indoor station
Indoor station
Outdoor
station
Power supply &
control unit Door release
relay and
illumination

4
Attention!
Do NOT connect terminal 29 (+) of TK SV 2500 REG
with terminal 25 (P) of power supply & control unit.
6-wire technique, Video
Please observe cable length and loop resistance.
Video indoor
station
Video indoor
station
Video outdoor
station
Power supply
& control unit
Floor
bell button
Floor
bell button
Door release
relay and
illumination

5
Wiring example for door release
Direct connected door release AC 12 V~.
Door release time from 0.8 s up to 8 s manually adjustable.
Wiring example with door release for postman key switch
The door release can be activated with an additional key switch. The door release remains
activated as long as the switch contact is closed. Please install the key switch only as
shown in the wiring example.
Wiring example with door release with external power supply
Door release systems with an external power supply and an alternative low voltage (AC or
DC) shall be installed only as shown in the wiring example.
The door release time is manually adjustable from 0.8 s up to 8 s.

6
Wiring example for light switching
The following various light functions trigger or retrigger the internal floating switch contact
(max. 24 V, DC 1 A).
Automatic light
switching The light will be switched depending on the ambient brightness when you push the bell button of the outdoor station. The limited
brightness value is adjustable.
Light switching The function button of the indoor station is assigned with the func-
tion "light switching" (factory setting). A bell button of the outdoor
station will switch the light, if the bell button is not assigned to an
indoor station.
Light switching
function
This door release button of the indoor station can be assigned
with a second function, when the light switching function is acti-
vated: You first have to push the communication button before
you can release the door with the door release button.
Without pushing the communication button you will switch the light
with the door release button.
! Mains voltage load circuits have to be switched with an external control relay.
The galvanic separation according to SELV is required.
Wiring example for a relay with external power supply
Connection of an external control relay for a load circuit to the time-controlled floating
contact (max. 24 V, 1 A).
Combination with an existing staircase installation
Connect the external relay to the terminals 14/15 of the TKSVSTG 60 REG.
Connect the switching contact of the external relay to the push-button terminal of the
existing staircase timer switch. The light switching time has to be set to the minimum at the
power supply & control unit.
Possible external control relay:
•Control relay of company Eltako ER12-001-8-230V UC

7
Wiring example for an external relay to the internal power supply
The power supply of an external staircase timer switch or control relay with an universal
voltage input is possible (AC 12 V, power supply for door release).
!Exclusively install relays with an universal voltage input and a max. control capacity of
250 mW. The galvanic separation according to SELV is required.
The control input of the relay is to be connected at the terminals 14 and 18. The terminals
15 and 16 have to be connected.
Possible relay types:
•Staircase timer switch TCS Art.-Nr.: FNA1000-0400 or TZ1-SG (with 8 V-24 V AC)
•Staircase timer switch Theben Elpa1
•Staircase timer switch Eltako TLZ12M-230V+8V..230V UC
•Control relay Eltako ER12-001-8-230V UC
Mounting
Rail mounting into distribution panel according to DIN EN 50022
Wiring
Type of cable: Standard telecommunication cables, e. g. J-Y (St) Y with twisted pairs and
a cross section of 0.6 mm or 0.8 mm.
•Connect the wires according to the wiring diagram.

8
Commissioning
!The total current of the indoor stations, outdoor stations and other devices may not ex-
ceed the output current I(P) of the des TK SV STG 60 REG.
•Install all devices of the DCM system
•Short-circuit test for a-, b- and P-wires
•Switch on supply voltage
Following functions should work without programming:
- Communication of indoor station with outdoor station
- Door release function
- Switching light
•Programming of entire DCM system is described in the manual of the outdoor station
Operation
Signs and symbols
Push the button briefly LED flashes slowly
Push the button until …. LED is illuminated
Release the button Next
Switch ON the programming mode of the device
The system is active, LED is illuminated
Push RUN/PROG button
briefly (< 1 s) LED flashes
Switch OFF the programming mode of the device
The system is active, LED flashes
Push RUN/PROG button
briefly (< 1 s) LED is illuminated

9
Settings
!To protect the system against manipulation, new programming of switching times will be
saved only by means of switching the programming mode on and off.
Door release time
The system is active, LED is illuminated
Set the time then switch the programming mode on and off
–: min. 1 s
+: max. 8 s Push RUN/PROG button briefly (< 1 s) LED flashes Push RUN/PROG button briefly (< 1 s) LED is illuminated
Light switching time
The system is active, LED is illuminated
Set the time then switch the programming mode on and off
–: min. 1 s
+: max. 5 min. Push RUN/PROG button briefly (< 1 s) LED flashes Push RUN/PROG button briefly (< 1 s) LED is illuminated

10
Light switch function
If the communication between indoor and outdoor station is NOT activated, you can switch
the light with the door release button.
Factory settings: Function is deactivated
Activate the light switch function
The system is active, LED is illuminated
Push RUN/PROG
button until… the LED flashes, then release button Push RUN/PROG button briefly (< 1 s) LED is illuminated
The flashing of the LED does NOT indicate, that the system is in programming mode.
Deactivate the light switch function
The system is active, LED is illuminated
short push of
RUN/PROG-
button (< 1 s) LED flashes
press
RUN/PROG-button
until
LED is illuminated,
then release button
The flashing of the LED does NOT indicate, that the system is in programming mode.
Technical Data
Input voltage:: AC 230 V~ ± 10 %, 50 / 60 Hz
Housing: rail mounting device, 4 rail units
DIN EN 60715 TH35
Weight: 475 g
Permissible ambient temperature: 0 ... + 40 °C
Output current a-terminal: I(a) = 40 mA
Output current P- terminal: I(P) = 60 mA
Output open circuit voltage: U(a/b) = 24 V ± 1 V, U(b/P) = 24V ± 1V
Output voltage talking: U(a/b) = 21 V ± 1 V
Door release open circuit voltage: U(Dr) = 12 V ± 2 V, 50 Hz (depending on load)
Switching contact light: floating make contact, 24 V DC / 1 A
EMC compatible: according to EN 50081 and EN 50082-2
Radio interference suppression: according to EN 55011

11
Acceptance of guarantee
We accept the guarantee in accordance with the corresponding legal provisions.
Please return the unit postage paid to our central service department giving
a brief description of the fault:
ALBRECHT JUNG GMBH & CO. KG
Service-Centre
Kupferstr. 17-19
44532 Lünen
Germany
Service-Line:0 23 55 . 80 65 51
Telefax: 0 23 55 . 80 61 89
E-Mail: [email protected]
Technique (DCM)
Service-Line: 0 23 55 . 80 65 52
Fax: 0 23 55 . 80 62 55
E-Mail: [email protected]



Albrecht Jung GmbH & Co. KG
P.O. Box 1320
58569 Schalksmühle
Germnany
www.gb.jung.de
www.jung-catalogue.com
The - sign is a free trade sign addressed
exclusively to the authorities and does not
include any warranty of any properties.
Technical subjects to change.
EN_TKSVSTG60REG.doc
02/2010