JVC ProHD FS-790 User manual

Printed in Japan
KCS-8422 CEFS790GKN1103
“JVC” is the trademark or registered trademark of Victor Company of Japan, Limited.
DISTRIBUTED BY
Simulated pictures.
The values for weight and dimensions are approximate.
E.&O.E. Design and specifications subject to change without notice.
Video, Digital (bi-directional)
Interface: SMPTE 259M, 292M
Data Rate: 270Mbps or 1.5Gbps
Input Level: 800mV (peak to peak)
Input/Output Impedance: 75Ω
Output Impedance: 75Ω
Bit-Error Rate (@ -22 dBm): 10 – 12
Jitter (pathological data): < 0.2UI
Rise/Fall Times: < 270ps
Video, Analog (bi-directional)
Interface: RS170, NTSC, PAL
Frequency Response
30Hz - 4.2MHz: ±0.15dB
8MHz: -3dB
Video Signal to Noise Ratio: 672dB
Differential Gain: < 2%
Differential Phase: < 1°
Audio
Number of Channels: 1 – 2
Type: Balanced, Line Level
Impedance: >15KΩ
Maximum Input Level: 24dBµ
Quantization: 24bits, 128x (oversampled)
Sample Rate: 48kS/sec.
Frequency Response: ±0.1dB, 20Hz to 20KHz
Intercom
Number or Channels: 1
Interface Types (Base): RTS or Clear-Com and 4-Wire
Frequency Response: 200 – 18KHz ±3dB
Max Distortion: ;0.5%
Noise: < -60dBµ
Max Gain (RTS or Clear-Com): :24dB
Min Gain (RTS or Clear-Com): ;-45dB
Electro-Optical
Operating Wavelengths: 1300nm/1550nm
TX Laser Output Power (std./opt): -6dBm/0dBm
RX Sensitivity, HD/SDI: -22 dBm
Fiber Compatibility: Single Mode
Mechanical/Environmental
Dimensions (W x L x D):
Camera Unit: 2.5" x 6.5" x 2.2"/6.35 x 16.51 x 5.58 cm
Base Station: 17.5" x 9" x 1.75"/44.45 x 22.86 x 4.44 cm
Power Wafer: 5" x 6.12" x 2.2"/12.7 x 15.54 x 5.58 cm
Weight:
Camera Unit: 1.5 lbs./0.68 kg
Base Station: 5.0 lbs./2.27 kg
Power Wafer: 1.5 lbs./0.68 kg
Power Consumption
Camera Unit: 8 watts@10-18VDC
Base Station (Tac Fiber): 10 watts@10-18VDC
Temperature Range: -25°to +55°C
Humidity Range: 0 to 95% RH, Non-condensing
Specifications
Product and company names mentioned here are trademarks or registered trademarks of their respective owners
●Round = Neutrik plug
◆Diamond = SMPTE plug
■Square = Plug type irrelevant
■ ◆●Green = Anton Bauer mount
■ ◆●Red = IDX mount
■ ◆●Black = Battery type irrelevant
White field = RTS intercom
Greyed field = ClearCom intercom
Fiber Cables
FS-CABTAC100 100 feet Tactical Cable/OpticalCON Connector
FS-CABTAC200 200 feet Tactical Cable/OpticalCON Connector
FS-CABTAC500 500 feet with reel Tactical Cable/OpticalCON Connector
FS-CABTAC1000 1000 feet with reel Tactical Cable/OpticalCON Connector
FS-CABTAC2000 2000 feet with reel Tactical Cable/OpticalCON Connector
FS-CABHYB100 100 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB200 200 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB500 500 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB700 700 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB100S 100 feet Hybrid Cable/SMPTE304M Connector
FS-CABHYB200S 200 feet Hybrid Cable/SMPTE304M Connector
FS-CABHYB500S 500 feet Hybrid Cable/SMPTE304M Connector
FS-CABHYB700S 700 feet Hybrid Cable/SMPTE304M Connector
Optional Fiber Cable and Connector Type
FS-790TNRG FS-790TNCG FS-790PNARG FS-790PNACG FS-790PNVRG FS-790PNVCG FS-790PSARG FS-790PSACG FS-790PSVRG FS-790PSVCG
KA-F790NG ●●●●●●
KA-F790SG ◆◆◆◆
RM-FP790TNRG ●
RM-FP790TNCG ●
RM-FP790PNRG ●●
RM-FP790PNCG ●●
RM-FP790PSRG ◆◆
RM-FP790PSCG ◆◆
KA-PW790AG ■■ ■■
KA-PW790VG ■■ ■■
AA-FP790G ■■
VC-P790RMG ■■■■■ ■■ ■■■
Type
Camera
Adapter
Base Station
Power Wafer
Power Supply
Remote Cable
Specifications Available with Each System
Business Solution Division of
Victor Company of Japan, Ltd.
has received ISO9001 Certifications.
JMI-0181
Realize full studio functionality for field
applications with one single fiber cable
The KA-F790 custom designed camera back transceiver
module attaches directly to the GY-HM790 body using a
hidden 68-pin connector and enables broadcasters to
leverage the GY-HM790’s full studio functionality in the field.
It connects the camera via SMPTE hybrid (powered) or
tactical (unpowered) fiber optic cable to the RM-FP790
CopperHead base station typically located in a control
room, flypack or OB van.
Ole Miss Athletics & Media Support Group
Edge Hill University
WZVN
Integrated Simplicity
ProHD Fiber Remote System
FS-790
FS-790 is marketed under Telecast brand.
Picture shows GY-HM790 with KA-F790NG Camera Adapter and KA-PW790AG Power Wafer

Unpowered Tactical Fiber Solution for Extended Distances
Powered Hybrid Fiber Solution with OpticalCON Connectors
Powered Hybrid Fiber Solution with SMPTE 304M Connectors
Base Station Camera Unit
HD/SDI VBS
SDI – HD/SDI Camera Video
Camera Control (RS232/422)
Audio 1
Audio 2
Time Code
Time Code
Audio Return
Intercom (One Channel)
Up to 10km on a single fiber-optic cable (2 strands)
Tally
SDI – HD/SDI Return Video
VBS Video (VBS Program)
VBS Return 1 (G/L)
VBS Return 2 (Return/Prompter)
VBS Return 3 (Return VBS)
SDI
HD/SDI
VBS
VBS
DATA,
TIME CODE,
TALLY
AUDIO
RM-LP25U
Offering up to 10km (6.2 miles) on Tactical or Infrastructure Single Mode Fiber
VC-P790RMG
Tactical Fiber Cable
on Reel
OpticalCON Plug
Battery or
AC Power
Supply AC Power Supply
AC Adapter
RM-FP790TNxx
OpticalCON Receptacle
OpticalCON
Receptacle
Offering up to 500m (1640 feet) on SMPTE Hybrid Fiber
VC-P790RMG
Hybrid Fiber Cable
OpticalCON Plug
Power Wafer
KA-PW790xx
Camera Unit
KA-F790xx
RM-FP790PNxx
OpticalCON Receptacle
OpticalCON
Receptacle
Offering up to 500m (1640 feet) on SMPTE Hybrid Fiber
VC-P790RMG
Hybrid Fiber Cable
SMPTE 304M Connectors
Camera Unit
KA-F790xx
RM-FP790PSxx
OpticalCON Receptacle
RM-LP25U/LP55U
Camera Unit
KA-F790xx
Professional System Solutions for
a Range of Remote Applications
The JVC ProHD fiber systems include a camera adapter (for the GY-HM790) and base station, with
either RTS intercom or CC (Clear-Com) compatibility. Additionally all units have a standard 4-Wire
intercom interface. Two types of fiber connections options are offered, Neutrik OpticalCON connectors
(powered or unpowered) and SMPTE 304M (powered).
GPI 1 In GPI 2 In
Time Code
Rdr/Gen
02 :12 :22 :27
Intercom
Program Audio
Return
Audio
HD/SDI
PGM #1
HD/SDI
PGM #2
VBS
Bi-Level or
Tri-Level
Sync
Generator
Return VBS
Video Source #1
Loop
Prompter
Ideal for a range of ENG and EFP applications, the FS-790 fiber optic multiplexing
system replaces bulky multicore cables with durable, lightweight fiber cable for robust
two-way communication between cameras and control systems.
An Integrated Fiber-based System for
Remote Applications
RM-FP790
Fiber Base Station
Easily integrated into any studio, portable flypack or OB van,
the lightweight, 1U rack-mountable Base Station plugs directly into a
facility’s switcher, router, intercom and house sync systems.
KA-F790
Remote Fiber Adapter
Ideal for use in studio/EFP
applications, the KA-F790
does not require any external
cabling and offers a clean
interface without clutter.
Full Control through Extended Base
Station Connections
Designed for total integration with existing
systems, the RM-FP790 base station offers
complete connections for video (two HD/SDI
outputs with return SDI and VBS connections
for analog signals), audio (RTS TW intercom
module) and sync/control functions (bi-level or
tri-level sync, prompter input, time code, GPI
signals and remote camera control input),
providing unprecedented control for a range of
field applications.
RM-FP790xxxx Base Station Connections
Power Wafer
KA-PW790xx
OpticalCON
Receptacle
Offers a direct connection to the camcorder without
requiring external cables
One single fiber cable covers all signals
necessary in ENG and EFP applications
The system simultaneously transports bidirectional digital
(SDI or HD-SDI) and analog (NTSC or PAL) video, as well as
all two-way camera control, audio, video, data, sync,
tally/call, prompter, and intercom signals between the
camera head and the remote Base Station. The lightweight,
1 RU RM-FP790 Base Station is easily integrated into any
studio, mobile truck, or portable flypack — and plugs directly
into a facility’s switcher, router, intercom, and house sync
systems.
RM-LP25U
RM-LP25U/LP55U
RM-LP25U/LP55U
KM-H3000
Picture shows KA-F790NG Camera Adapter and KA-PW790AG Power Wafer
Picture shows GY-HM790 with KA-F790NG Camera Adapter
and KA-PW790AG Power Wafer

Printed in Japan
KCS-8422 CEFS790GKN1103
“JVC” is the trademark or registered trademark of Victor Company of Japan, Limited.
DISTRIBUTED BY
Simulated pictures.
The values for weight and dimensions are approximate.
E.&O.E. Design and specifications subject to change without notice.
Video, Digital (bi-directional)
Interface: SMPTE 259M, 292M
Data Rate: 270Mbps or 1.5Gbps
Input Level: 800mV (peak to peak)
Input/Output Impedance: 75Ω
Output Impedance: 75Ω
Bit-Error Rate (@ -22 dBm): 10 – 12
Jitter (pathological data): < 0.2UI
Rise/Fall Times: < 270ps
Video, Analog (bi-directional)
Interface: RS170, NTSC, PAL
Frequency Response
30Hz - 4.2MHz: ±0.15dB
8MHz: -3dB
Video Signal to Noise Ratio: 672dB
Differential Gain: < 2%
Differential Phase: < 1°
Audio
Number of Channels: 1 – 2
Type: Balanced, Line Level
Impedance: >15KΩ
Maximum Input Level: 24dBµ
Quantization: 24bits, 128x (oversampled)
Sample Rate: 48kS/sec.
Frequency Response: ±0.1dB, 20Hz to 20KHz
Intercom
Number or Channels: 1
Interface Types (Base): RTS or Clear-Com and 4-Wire
Frequency Response: 200 – 18KHz ±3dB
Max Distortion: ;0.5%
Noise: < -60dBµ
Max Gain (RTS or Clear-Com): :24dB
Min Gain (RTS or Clear-Com): ;-45dB
Electro-Optical
Operating Wavelengths: 1300nm/1550nm
TX Laser Output Power (std./opt): -6dBm/0dBm
RX Sensitivity, HD/SDI: -22 dBm
Fiber Compatibility: Single Mode
Mechanical/Environmental
Dimensions (W x L x D):
Camera Unit: 2.5" x 6.5" x 2.2"/6.35 x 16.51 x 5.58 cm
Base Station: 17.5" x 9" x 1.75"/44.45 x 22.86 x 4.44 cm
Power Wafer: 5" x 6.12" x 2.2"/12.7 x 15.54 x 5.58 cm
Weight:
Camera Unit: 1.5 lbs./0.68 kg
Base Station: 5.0 lbs./2.27 kg
Power Wafer: 1.5 lbs./0.68 kg
Power Consumption
Camera Unit: 8 watts@10-18VDC
Base Station (Tac Fiber): 10 watts@10-18VDC
Temperature Range: -25°to +55°C
Humidity Range: 0 to 95% RH, Non-condensing
Specifications
Product and company names mentioned here are trademarks or registered trademarks of their respective owners
●Round = Neutrik plug
◆Diamond = SMPTE plug
■Square = Plug type irrelevant
■ ◆●Green = Anton Bauer mount
■ ◆●Red = IDX mount
■ ◆●Black = Battery type irrelevant
White field = RTS intercom
Greyed field = ClearCom intercom
Fiber Cables
FS-CABTAC100 100 feet Tactical Cable/OpticalCON Connector
FS-CABTAC200 200 feet Tactical Cable/OpticalCON Connector
FS-CABTAC500 500 feet with reel Tactical Cable/OpticalCON Connector
FS-CABTAC1000 1000 feet with reel Tactical Cable/OpticalCON Connector
FS-CABTAC2000 2000 feet with reel Tactical Cable/OpticalCON Connector
FS-CABHYB100 100 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB200 200 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB500 500 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB700 700 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB100S 100 feet Hybrid Cable/SMPTE304M Connector
FS-CABHYB200S 200 feet Hybrid Cable/SMPTE304M Connector
FS-CABHYB500S 500 feet Hybrid Cable/SMPTE304M Connector
FS-CABHYB700S 700 feet Hybrid Cable/SMPTE304M Connector
Optional Fiber Cable and Connector Type
FS-790TNRG FS-790TNCG FS-790PNARG FS-790PNACG FS-790PNVRG FS-790PNVCG FS-790PSARG FS-790PSACG FS-790PSVRG FS-790PSVCG
KA-F790NG ●●●●●●
KA-F790SG ◆◆◆◆
RM-FP790TNRG ●
RM-FP790TNCG ●
RM-FP790PNRG ●●
RM-FP790PNCG ●●
RM-FP790PSRG ◆◆
RM-FP790PSCG ◆◆
KA-PW790AG ■■ ■■
KA-PW790VG ■■ ■■
AA-FP790G ■■
VC-P790RMG ■■■■■ ■■ ■■■
Type
Camera
Adapter
Base Station
Power Wafer
Power Supply
Remote Cable
Specifications Available with Each System
Business Solution Division of
Victor Company of Japan, Ltd.
has received ISO9001 Certifications.
JMI-0181
Realize full studio functionality for field
applications with one single fiber cable
The KA-F790 custom designed camera back transceiver
module attaches directly to the GY-HM790 body using a
hidden 68-pin connector and enables broadcasters to
leverage the GY-HM790’s full studio functionality in the field.
It connects the camera via SMPTE hybrid (powered) or
tactical (unpowered) fiber optic cable to the RM-FP790
CopperHead base station typically located in a control
room, flypack or OB van.
Ole Miss Athletics & Media Support Group
Edge Hill University
WZVN
Integrated Simplicity
ProHD Fiber Remote System
FS-790
FS-790 is marketed under Telecast brand.
Picture shows GY-HM790 with KA-F790NG Camera Adapter and KA-PW790AG Power Wafer

Unpowered Tactical Fiber Solution for Extended Distances
Powered Hybrid Fiber Solution with OpticalCON Connectors
Powered Hybrid Fiber Solution with SMPTE 304M Connectors
Base Station Camera Unit
HD/SDI VBS
SDI – HD/SDI Camera Video
Camera Control (RS232/422)
Audio 1
Audio 2
Time Code
Time Code
Audio Return
Intercom (One Channel)
Up to 10km on a single fiber-optic cable (2 strands)
Tally
SDI – HD/SDI Return Video
VBS Video (VBS Program)
VBS Return 1 (G/L)
VBS Return 2 (Return/Prompter)
VBS Return 3 (Return VBS)
SDI
HD/SDI
VBS
VBS
DATA,
TIME CODE,
TALLY
AUDIO
RM-LP25U
Offering up to 10km (6.2 miles) on Tactical or Infrastructure Single Mode Fiber
VC-P790RMG
Tactical Fiber Cable
on Reel
OpticalCON Plug
Battery or
AC Power
Supply AC Power Supply
AC Adapter
RM-FP790TNxx
OpticalCON Receptacle
OpticalCON
Receptacle
Offering up to 500m (1640 feet) on SMPTE Hybrid Fiber
VC-P790RMG
Hybrid Fiber Cable
OpticalCON Plug
Power Wafer
KA-PW790xx
Camera Unit
KA-F790xx
RM-FP790PNxx
OpticalCON Receptacle
OpticalCON
Receptacle
Offering up to 500m (1640 feet) on SMPTE Hybrid Fiber
VC-P790RMG
Hybrid Fiber Cable
SMPTE 304M Connectors
Camera Unit
KA-F790xx
RM-FP790PSxx
OpticalCON Receptacle
RM-LP25U/LP55U
Camera Unit
KA-F790xx
Professional System Solutions for
a Range of Remote Applications
The JVC ProHD fiber systems include a camera adapter (for the GY-HM790) and base station, with
either RTS intercom or CC (Clear-Com) compatibility. Additionally all units have a standard 4-Wire
intercom interface. Two types of fiber connections options are offered, Neutrik OpticalCON connectors
(powered or unpowered) and SMPTE 304M (powered).
GPI 1 In GPI 2 In
Time Code
Rdr/Gen
02 :12 :22 :27
Intercom
Program Audio
Return
Audio
HD/SDI
PGM #1
HD/SDI
PGM #2
VBS
Bi-Level or
Tri-Level
Sync
Generator
Return VBS
Video Source #1
Loop
Prompter
Ideal for a range of ENG and EFP applications, the FS-790 fiber optic multiplexing
system replaces bulky multicore cables with durable, lightweight fiber cable for robust
two-way communication between cameras and control systems.
An Integrated Fiber-based System for
Remote Applications
RM-FP790
Fiber Base Station
Easily integrated into any studio, portable flypack or OB van,
the lightweight, 1U rack-mountable Base Station plugs directly into a
facility’s switcher, router, intercom and house sync systems.
KA-F790
Remote Fiber Adapter
Ideal for use in studio/EFP
applications, the KA-F790
does not require any external
cabling and offers a clean
interface without clutter.
Full Control through Extended Base
Station Connections
Designed for total integration with existing
systems, the RM-FP790 base station offers
complete connections for video (two HD/SDI
outputs with return SDI and VBS connections
for analog signals), audio (RTS TW intercom
module) and sync/control functions (bi-level or
tri-level sync, prompter input, time code, GPI
signals and remote camera control input),
providing unprecedented control for a range of
field applications.
RM-FP790xxxx Base Station Connections
Power Wafer
KA-PW790xx
OpticalCON
Receptacle
Offers a direct connection to the camcorder without
requiring external cables
One single fiber cable covers all signals
necessary in ENG and EFP applications
The system simultaneously transports bidirectional digital
(SDI or HD-SDI) and analog (NTSC or PAL) video, as well as
all two-way camera control, audio, video, data, sync,
tally/call, prompter, and intercom signals between the
camera head and the remote Base Station. The lightweight,
1 RU RM-FP790 Base Station is easily integrated into any
studio, mobile truck, or portable flypack — and plugs directly
into a facility’s switcher, router, intercom, and house sync
systems.
RM-LP25U
RM-LP25U/LP55U
RM-LP25U/LP55U
KM-H3000
Picture shows KA-F790NG Camera Adapter and KA-PW790AG Power Wafer
Picture shows GY-HM790 with KA-F790NG Camera Adapter
and KA-PW790AG Power Wafer

Unpowered Tactical Fiber Solution for Extended Distances
Powered Hybrid Fiber Solution with OpticalCON Connectors
Powered Hybrid Fiber Solution with SMPTE 304M Connectors
Base Station Camera Unit
HD/SDI VBS
SDI – HD/SDI Camera Video
Camera Control (RS232/422)
Audio 1
Audio 2
Time Code
Time Code
Audio Return
Intercom (One Channel)
Up to 10km on a single fiber-optic cable (2 strands)
Tally
SDI – HD/SDI Return Video
VBS Video (VBS Program)
VBS Return 1 (G/L)
VBS Return 2 (Return/Prompter)
VBS Return 3 (Return VBS)
SDI
HD/SDI
VBS
VBS
DATA,
TIME CODE,
TALLY
AUDIO
RM-LP25U
Offering up to 10km (6.2 miles) on Tactical or Infrastructure Single Mode Fiber
VC-P790RMG
Tactical Fiber Cable
on Reel
OpticalCON Plug
Battery or
AC Power
Supply AC Power Supply
AC Adapter
RM-FP790TNxx
OpticalCON Receptacle
OpticalCON
Receptacle
Offering up to 500m (1640 feet) on SMPTE Hybrid Fiber
VC-P790RMG
Hybrid Fiber Cable
OpticalCON Plug
Power Wafer
KA-PW790xx
Camera Unit
KA-F790xx
RM-FP790PNxx
OpticalCON Receptacle
OpticalCON
Receptacle
Offering up to 500m (1640 feet) on SMPTE Hybrid Fiber
VC-P790RMG
Hybrid Fiber Cable
SMPTE 304M Connectors
Camera Unit
KA-F790xx
RM-FP790PSxx
OpticalCON Receptacle
RM-LP25U/LP55U
Camera Unit
KA-F790xx
Professional System Solutions for
a Range of Remote Applications
The JVC ProHD fiber systems include a camera adapter (for the GY-HM790) and base station, with
either RTS intercom or CC (Clear-Com) compatibility. Additionally all units have a standard 4-Wire
intercom interface. Two types of fiber connections options are offered, Neutrik OpticalCON connectors
(powered or unpowered) and SMPTE 304M (powered).
GPI 1 In GPI 2 In
Time Code
Rdr/Gen
02 :12 :22 :27
Intercom
Program Audio
Return
Audio
HD/SDI
PGM #1
HD/SDI
PGM #2
VBS
Bi-Level or
Tri-Level
Sync
Generator
Return VBS
Video Source #1
Loop
Prompter
Ideal for a range of ENG and EFP applications, the FS-790 fiber optic multiplexing
system replaces bulky multicore cables with durable, lightweight fiber cable for robust
two-way communication between cameras and control systems.
An Integrated Fiber-based System for
Remote Applications
RM-FP790
Fiber Base Station
Easily integrated into any studio, portable flypack or OB van,
the lightweight, 1U rack-mountable Base Station plugs directly into a
facility’s switcher, router, intercom and house sync systems.
KA-F790
Remote Fiber Adapter
Ideal for use in studio/EFP
applications, the KA-F790
does not require any external
cabling and offers a clean
interface without clutter.
Full Control through Extended Base
Station Connections
Designed for total integration with existing
systems, the RM-FP790 base station offers
complete connections for video (two HD/SDI
outputs with return SDI and VBS connections
for analog signals), audio (RTS TW intercom
module) and sync/control functions (bi-level or
tri-level sync, prompter input, time code, GPI
signals and remote camera control input),
providing unprecedented control for a range of
field applications.
RM-FP790xxxx Base Station Connections
Power Wafer
KA-PW790xx
OpticalCON
Receptacle
Offers a direct connection to the camcorder without
requiring external cables
One single fiber cable covers all signals
necessary in ENG and EFP applications
The system simultaneously transports bidirectional digital
(SDI or HD-SDI) and analog (NTSC or PAL) video, as well as
all two-way camera control, audio, video, data, sync,
tally/call, prompter, and intercom signals between the
camera head and the remote Base Station. The lightweight,
1 RU RM-FP790 Base Station is easily integrated into any
studio, mobile truck, or portable flypack — and plugs directly
into a facility’s switcher, router, intercom, and house sync
systems.
RM-LP25U
RM-LP25U/LP55U
RM-LP25U/LP55U
KM-H3000
Picture shows KA-F790NG Camera Adapter and KA-PW790AG Power Wafer
Picture shows GY-HM790 with KA-F790NG Camera Adapter
and KA-PW790AG Power Wafer

Printed in Japan
KCS-8422 CEFS790GKN1103
“JVC” is the trademark or registered trademark of Victor Company of Japan, Limited.
DISTRIBUTED BY
Simulated pictures.
The values for weight and dimensions are approximate.
E.&O.E. Design and specifications subject to change without notice.
Video, Digital (bi-directional)
Interface: SMPTE 259M, 292M
Data Rate: 270Mbps or 1.5Gbps
Input Level: 800mV (peak to peak)
Input/Output Impedance: 75Ω
Output Impedance: 75Ω
Bit-Error Rate (@ -22 dBm): 10 – 12
Jitter (pathological data): < 0.2UI
Rise/Fall Times: < 270ps
Video, Analog (bi-directional)
Interface: RS170, NTSC, PAL
Frequency Response
30Hz - 4.2MHz: ±0.15dB
8MHz: -3dB
Video Signal to Noise Ratio: 672dB
Differential Gain: < 2%
Differential Phase: < 1°
Audio
Number of Channels: 1 – 2
Type: Balanced, Line Level
Impedance: >15KΩ
Maximum Input Level: 24dBµ
Quantization: 24bits, 128x (oversampled)
Sample Rate: 48kS/sec.
Frequency Response: ±0.1dB, 20Hz to 20KHz
Intercom
Number or Channels: 1
Interface Types (Base): RTS or Clear-Com and 4-Wire
Frequency Response: 200 – 18KHz ±3dB
Max Distortion: ;0.5%
Noise: < -60dBµ
Max Gain (RTS or Clear-Com): :24dB
Min Gain (RTS or Clear-Com): ;-45dB
Electro-Optical
Operating Wavelengths: 1300nm/1550nm
TX Laser Output Power (std./opt): -6dBm/0dBm
RX Sensitivity, HD/SDI: -22 dBm
Fiber Compatibility: Single Mode
Mechanical/Environmental
Dimensions (W x L x D):
Camera Unit: 2.5" x 6.5" x 2.2"/6.35 x 16.51 x 5.58 cm
Base Station: 17.5" x 9" x 1.75"/44.45 x 22.86 x 4.44 cm
Power Wafer: 5" x 6.12" x 2.2"/12.7 x 15.54 x 5.58 cm
Weight:
Camera Unit: 1.5 lbs./0.68 kg
Base Station: 5.0 lbs./2.27 kg
Power Wafer: 1.5 lbs./0.68 kg
Power Consumption
Camera Unit: 8 watts@10-18VDC
Base Station (Tac Fiber): 10 watts@10-18VDC
Temperature Range: -25°to +55°C
Humidity Range: 0 to 95% RH, Non-condensing
Specifications
Product and company names mentioned here are trademarks or registered trademarks of their respective owners
●Round = Neutrik plug
◆Diamond = SMPTE plug
■Square = Plug type irrelevant
■ ◆●Green = Anton Bauer mount
■ ◆●Red = IDX mount
■ ◆●Black = Battery type irrelevant
White field = RTS intercom
Greyed field = ClearCom intercom
Fiber Cables
FS-CABTAC100 100 feet Tactical Cable/OpticalCON Connector
FS-CABTAC200 200 feet Tactical Cable/OpticalCON Connector
FS-CABTAC500 500 feet with reel Tactical Cable/OpticalCON Connector
FS-CABTAC1000 1000 feet with reel Tactical Cable/OpticalCON Connector
FS-CABTAC2000 2000 feet with reel Tactical Cable/OpticalCON Connector
FS-CABHYB100 100 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB200 200 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB500 500 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB700 700 feet Hybrid Cable/OpticalCON Connector
FS-CABHYB100S 100 feet Hybrid Cable/SMPTE304M Connector
FS-CABHYB200S 200 feet Hybrid Cable/SMPTE304M Connector
FS-CABHYB500S 500 feet Hybrid Cable/SMPTE304M Connector
FS-CABHYB700S 700 feet Hybrid Cable/SMPTE304M Connector
Optional Fiber Cable and Connector Type
FS-790TNRG FS-790TNCG FS-790PNARG FS-790PNACG FS-790PNVRG FS-790PNVCG FS-790PSARG FS-790PSACG FS-790PSVRG FS-790PSVCG
KA-F790NG ●●●●●●
KA-F790SG ◆◆◆◆
RM-FP790TNRG ●
RM-FP790TNCG ●
RM-FP790PNRG ●●
RM-FP790PNCG ●●
RM-FP790PSRG ◆◆
RM-FP790PSCG ◆◆
KA-PW790AG ■■ ■■
KA-PW790VG ■■ ■■
AA-FP790G ■■
VC-P790RMG ■■■■■ ■■ ■■■
Type
Camera
Adapter
Base Station
Power Wafer
Power Supply
Remote Cable
Specifications Available with Each System
Business Solution Division of
Victor Company of Japan, Ltd.
has received ISO9001 Certifications.
JMI-0181
Realize full studio functionality for field
applications with one single fiber cable
The KA-F790 custom designed camera back transceiver
module attaches directly to the GY-HM790 body using a
hidden 68-pin connector and enables broadcasters to
leverage the GY-HM790’s full studio functionality in the field.
It connects the camera via SMPTE hybrid (powered) or
tactical (unpowered) fiber optic cable to the RM-FP790
CopperHead base station typically located in a control
room, flypack or OB van.
Ole Miss Athletics & Media Support Group
Edge Hill University
WZVN
Integrated Simplicity
ProHD Fiber Remote System
FS-790
FS-790 is marketed under Telecast brand.
Picture shows GY-HM790 with KA-F790NG Camera Adapter and KA-PW790AG Power Wafer