JVC RM-SRX7020J User manual

34
Operating JVC’s Audio/Video Components
You can use the remote control to operate other JVC’s
components.
Operating Audio Components
IMPORTANT:
To operate JVC’s audio components using this remote control:
•You need to connect JVC’s audio components through the COMPU
LINK-4 (SYNCHRO) jacks (see page 31) in addition to the
connections using cables with RCA pin plugs (see page 7).
•Aim the remote control directly at the remote sensor on the receiver.
•If you use the buttons on the front panel, the remote control will not
operate that source. To operate a source with the remote control,
the source must be selected using source selecting buttons on the
remote control.
•To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 11.)
•Refer also to the manuals supplied with your audio components.
Sound Adjustment
You can always use the following buttons:
SURROUND ON/OFF : Turn on or off the Surround modes.
SURROUND MODE :Select the Surround modes.
After pressing SOUND, you can use the following buttons for sound
adjustment:
SUBWOOFER +/–:Adjust the subwoofer output level.
CENTER +/–:Adjust the center speaker output level.
REAR•L +/–:Adjust the left rear speaker output level.
REAR•R +/–:Adjust the right rear speaker output level.
EFFECT :Select the DAP effect level.
TEST : Turn on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting
button or CONTROL to operate your target source by using the 10
keys; otherwise, the 10 keys cannot be used for operating your target
source.
Tuner
You can always use the following buttons:
FM/AM :Alternate between FM and AM.
After pressing FM/AM, you can use the following buttons for tuner
operations:
1 –10, +10 :Select a preset channel number directly.
•For channel number 5, press 5.
•For channel number 15, press +10, then 5.
•For channel number 20, press +10, then 10.
TUNING +/–: Tune into stations.
FM MODE :Change the FM reception mode.
CONTROL
+
−
+
−
+
−
231
564
897/P
0
+1010
BASS BOOST EFFECT
MENU
ENTER
TEST
DIMMER
MUTING
CH TV VOL
/REW FF/
VOLUME
CATV/DBS
CONTROL
TV/VIDEO
REC
TUNING
PAUSE
RETURN FM MODE 100+
CONTROL
A/V CONTROL RECEIVER
RM-SRX7020J REMOTE CONTROL
CATV/DBS VCR TV AUDIO
SURROUND
MODE INPUTON/OFF
DVD MULTIDVD CD
TAPE/CDR
TREBLE
TV/DBS VCR PHONO
FM/AM
BASS
SURROUND ANALOG/DIGITAL SLEEP
+
−
–SUB WOOFER +
–REAR •R +
–REAR •L +
–CENTER +
−− ++
SOUND
When you press one of the following buttons, the remote
control operation mode appears on the display window.
A/V CONTROL RECEIVER
Ex.: When you press CD.
Buttons on the Remote Control Remote Control Operation Mode
FM/AM TUNER
CD CD
PHONO PHONO
TAPE/CDR TAPE
DVD DVD
DVD MULTI DVD
TV/DBS TV
VCR VCR
CATV/DBS CONTROL DBS
CONTROL VCR or TAPE or CDDSC
SOUND SOUND
EN30-42.RX-7020V[J]f 01.12.27, 3:37 PM34

35
CD player
After pressing CD, you can use the following buttons for CD
operations:
33
33
3:Start playback.
4:Return to the beginning of the current
(or previous) track.
¢:Skip to the beginning of the next track.
77
77
7:Stop playback.
88
88
8: Pause playback. To release it, press 33
33
3.
1 –10, +10 :Select a track number directly.
•For track number 5, press 5.
•For track number 15, press +10, then 5.
•For track number 20, press +10, then 10.
CD changer
After pressing CONTROL repeatedly until “CDDSC”appears on
the display window, you can perform the following operations on
the CD changer:
33
33
3:Start playback.
4:Return to the beginning of the current
(or previous) track.
¢:Skip to the beginning of the next track.
77
77
7:Stop playback.
88
88
8: Pause playback. To release it, press 33
33
3.
1 –6, 7/P :Select the number of a disc installed in a CD
changer.
After pressing CD, you can perform the following operations on the
CD changer:
1 –10, +10 :Select a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
Example:
•Selecting disc number 4, track number 12, and starting playback.
1. Press CONTROL repeatedly until “CDDSC”appears on the
display window, then press 4.
2. Press CD, then press +10, 2.
If your CD changer is of 200-disc loading capability (except for
XL-MC100 and XL-MC301),
you can do the following operations using the number buttons after
pressing CD:
1 Select a disc number.
2 Then select a track number (always enter two digits).
3 Start playback.
Examples:
•Selecting disc number 3, track number 2, and starting playback.
Press 3, then, 0, 2, then 3.
•Selecting disc number 10, track number 5, and starting playback.
Press 1, 0, then, 0, 5, then 3.
•Selecting disc number 105, track number 12, and starting
playback.
Press 1, 0, 5, then 1, 2, then 3.
Turntable
After pressing PHONO, you can perform the following operations
on the turntable:
3:Start playing.
7:Stop operations.
Cassette deck
After pressing TAPE/CDR (or CONTROL repeatedly until “TAPE”
appears on the display window), you can use the following buttons
for cassette deck operations:
33
33
3:Start playback.
FF : Fast wind a tape from left to right.
REW : Fast wind a tape from right to left.
77
77
7:Stop playback or recording.
88
88
8: Pause playback. To release it, press 3.
REC PAUSE : Press this button to enter recording pause.
Press this button then 3to start recording.
Notes:
•Before starting the above operations, make sure that you have
changed the source name correctly. See page 11.
•You can use either TAPE/CDR button or CONTROL button to
activate the buttons listed above. If you press TAPE/CDR, the
playing source also changes. On the other hand, if you press
CONTROL repeatedly to select “TAPE,”the playing source does not
change.
CD recorder
After pressing TAPE/CDR (or CONTROL repeatedly until “TAPE”
appears on the display window), you can use the following buttons
for CD recorder operations:
33
33
3:Start playback.
4:Return to the beginning of the current
(or previous) track.
¢:Skip to the beginning of the next track.
77
77
7:Stop playback.
88
88
8: Pause playback. To release it, press 33
33
3.
REC PAUSE : Press this button to enter recording pause.
Press this button then 3to start recording.
Notes:
•Before starting the above operations, make sure that you have
changed the source name correctly. See page 11.
•“TAPE”appears on the display window even though you have
changed the source name to “CDR.”
•You can use either TAPE/CDR button or CONTROL button to
activate the buttons listed above. If you press TAPE/CDR, the
playing source also changes. On the other hand, if you press
CONTROL repeatedly to select “TAPE,”the playing source does not
change.
Operating JVC’s Audio/Video Components
EN30-42.RX-7020V[J]f 01.12.27, 3:37 PM35

36
Operating Video Components
IMPORTANT:
To operate JVC’s video components using this remote control:
•You need to connect JVC’s video components through the AV
COMPU LINK terminals (see page 32) in addition to the
connections using cables with RCA pin plugs (see pages 7 and 8).
•Some JVC’s VCRs can accept two types of the control signals —
remote code “A”and “B.”Before using this remote control, make
sure that the remote control code of the VCR connected to the
VCR jacks is set to code “A.”
•When using the remote control:
–For the DVD player and VCR operations, aim the remote control
directly at the remote sensor on each component, not on the
receiver.
–For the TV having the AV COMPU LINK terminal, aim the remote
control directly at the remote sensor on the TV.
VCR
You can always perform the following operations:
VCR : Turn on or off a VCR.
After pressing VCR (or CONTROL repeatedly until “VCR”appears
on the display window), you can use the following buttons for VCR
operations:
33
33
3:Start playback.
FF : Fast wind a tape.
REW : Rewind a tape.
77
77
7:Stop playback or recording.
88
88
8: Pause playback. To release it, press 33
33
3.
1 –9, 0 :Select a TV channel on the VCR.
REC PAUSE : Press this button to enter recording pause.
Press this button then 3to start recording.
CH +/–:Change the TV channels on the VCR.
Note:
•You can use either VCR button or CONTROL button to activate the
buttons listed above. If you press VCR, the playing source also
changes. On the other hand, if you press CONTROL repeatedly to
select “VCR,”the playing source does not change.
DVD player
After pressing DVD or DVD MULTI (source selecting button), you
can use the following buttons for DVD operations:
33
33
3:Start playback.
4:Return to the beginning of the current
(or previous) track.
¢:Skip to the beginning of the next track.
77
77
7:Stop playback.
88
88
8: Pause playback. To release it, press 33
33
3.
DVD menu operations
After pressing DVD or DVD MULTI
(source selecting button), you can use
the following buttons for DVD menu
operations:
MENU :Display or erase the menu screen.
55
55
5/∞∞
∞∞
∞/33
33
3/22
22
2:Select an item on the menu screen.
ENTER :Enter a selected item.
TV
You can always perform the following operations:
TV :Turn on or off a TV or a CATV converter.
TV/VIDEO :Change the input mode (TV tuner and video
input).
TV VOL +/–:Adjust the volume.
After pressing TV/DBS (source selecting button), you can use the
following buttons for TV operations:
CH +/–:Change the channels.
1 –9, 0, +10 (100+) :Select a channel.
RETURN (10) :Function as the RETURN button.
Operating JVC’s Audio/Video Components
231
564
897/P
0 +1010
EFFECT
TEST
RETURN FM MODE 100+
–SUB WOOFER +
–REAR •R +
–REAR •L +
–CENTER +
MENU
ENTER
EN30-42.RX-7020V[J]f 01.12.27, 3:37 PM36

37
Operating Other Manufacturers’Video Equipment
By changing the transmittable signals, you can use the remote
control supplied for this unit to operate other manufacturers’
equipment.
•Refer also to the manuals supplied for the other products.
•To operate these components with the remote control, first you
need to set the manufacturers’code each for TV, CATV converter,
VCR and DVD player.
•After replacing batteries of the remote control, set the
manufacturers’codes again.
To change the transmittable signals
for operating a TV
1 Press and hold TV .
2 Press TV/DBS.
3 Enter manufacturer’s codes using buttons 1 –9,
and 0.
4 Release TV .
Now, you can perform the following operations on the TV.
TV :Turn on or off the TV.
TV/VIDEO :Set the input mode (either TV or VIDEO).
TV VOL +/–:Adjust the volume.
After pressing TV/DBS, you can perform the following
operations on the TV:
CH +/–:Change the channels.
1 –9, 0, +10 (100+) :Select a channel.
10 :Function as the ENTER button.
Note:
Refer also to the manual supplied with your TV.
5 Try to operate your TV by pressing TV .
When your TV turns on or off, you have entered the correct
codes.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
Operating JVC’s Audio/Video Components / Operating Other Manufacturers’Video Equipment
Manufacturer Codes
JVC 00*, 02, 13, 14, 47, 74
AKAI 01, 02
BLAUPUNKT 03, 04
FISHER 01, 05
GRUNDIG 03, 06, 07
HITACHI 08, 09, 10, 49
IRADDIO 02
ITT/NOKIA 11, 12
LOEWE 06, 15, 16
MAGNAVOX 08, 17, 49
METS 50, 51, 52, 53
MITSUBISHI 08, 18, 19, 20
MIVAR 21
NORDMENDE 22, 23
OKANO 15
PANASONIC 24, 25, 26, 27, 76
PHILIPS 15, 17, 28, 75
QUELLE 52, 53, 54, 55, 56, 57, 58,
59, 60, 61, 62, 63, 64, 65,
66, 67
RCA/PROSCAN 08, 24, 29, 30, 31, 48
SABA 32, 33, 68, 69, 70
SAMSUNG 06, 08, 16, 34, 35, 49
SANYO 01, 05
SCHNEIDER 02, 15, 36
SHARP 37, 38, 77
SONY 39
TELEFUNKEN 40, 41, 42, 69
THOMSON 71, 72
TOSHIBA 37, 43, 44
ZENITH 45, 46
Manufacturers’codes for TV
* “00”is the initial setting.
Manufacturers’codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
TO BE CONTINUED TO THE NEXT PAGE
To change the transmittable signals for
operating a CATV converter or DBS tuner
1 Press and hold CATV/DBS .
2 Press CATV/DBS CONTROL.
3 Enter manufacturer’s codes using buttons 1 –9,
and 0.
4 Release CATV/DBS .
Now, you can perform the following operations on the CATV
converter or DBS tuner.
CATV/DBS : Turn on or off the CATV converter or DBS tuner.
After pressing CATV/DBS CONTROL, you can perform the
following operations on the CATV converter or DBS tuner:
CH +/–:Change the channels.
1 –9, 0, +10 (100+) :Select the channels.
10 :Function as the ENTER button.
Note:
Refer also to the manual supplied with your CATV converter or
DBS tuner.
EN30-42.RX-7020V[J]f 01.12.27, 3:37 PM37

38
5 Try to operate your CATV converter or DBS
tuner by pressing CATV/DBS .
When your CATV converter or DBS tuner turns on or off, you
have entered the correct codes.
If there are more than one code listed for your brand of
CATV converter or DBS tuner, try each one until the correct
one is entered.
Note:
You cannot use both the CATV converter and DBS tuner at the same
time.
To change the transmittable signals for
operating a VCR
1 Press and hold VCR .
2 Press VCR.
3 Enter manufacturer’s codes using buttons 1 –9,
and 0.
4 Release VCR .
Now, you can perform the following operations on the VCR.
VCR : Turn on or off the VCR.
After pressing VCR, you can perform the following operations
on the VCR:
CH +/–:Change the channels.
1 –9, 0, +10 (100+) :Select the channels.
10 :Function as ENTER button.
3:Start playback.
FF : Fast-wind a tape.
REW : Rewind a tape.
7:Stop playback or recording.
8: Pause playback. To release it, press 33
33
3.
REC PAUSE : Press this button to enter recording
pause.
Then press 3to start recording.
Note:
Refer also to the manual supplied with your VCR.
5 Try to operate your VCR by pressing
VCR .
When your VCR turns on or off, you have entered the correct
codes.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
Operating Other Manufacturers’Video Equipment
Manufacturers’codes for CATV converter
Manufacturer Codes
GENERAL INSTRUMENT 06, 07, 08, 09, 10,
11, 12, 13, 14, 29
HAMLIN/REGAL 01, 02, 03, 04, 05
JERROLD 06, 07, 08, 09, 10,
11, 12, 13, 14
OAK 15, 16, 17
PANASONIC 18, 19, 20
PIONEER 21, 22
SCIENTIFIC ATLANTA 23, 24, 25
TOCOM 26
ZENITH 27, 28
Manufacturers’codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
Manufacturer Codes
JVC 56, 57*, 67
AMSTRAD 43, 44, 45, 46, 47
BLAUPUNKT 30
ECHOSTAR 50, 51, 67
GOLDSTAR 31
GRUNDIG 32, 33
HIRSHMANN 48, 52, 53, 55
INSTRUMENT 68
ITT/NOKIA 34
KATHREIN 52, 58, 61, 62, 63
NEC 35, 36
ORBITECH 48
PHILIPS 37, 38
RCA 65
SAMSUNG 39, 40
SCHWAIGER 61, 64
SIEMENS 41, 42
SONY 66
TECHNISAT 48
Manufacturers’codes for DBS tuner
*
“57”is the initial setting.
Manufacturers’codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
EN30-42.RX-7020V[J]f 01.12.27, 3:37 PM38

39
To change the transmittable signals for
operating a DVD player
1 Press and hold AUDIO .
2 Press DVD.
3 Enter manufacturer’s codes using buttons 1 –9,
and 0.
4 Release AUDIO .
Now, you can use the following buttons on the DVD player.
3:Start playback.
7:Stop playback.
¢:Skip to the beginning of the next track.
4:Return to the beginning of the current
(or previous) track.
8: Pause playback. To release it, press 3.
DVD menu operations
After pressing DVD (source
selecting button), you can use the
following buttons for DVD menu
operations:
MENU :Display or erase the menu screen.
55
55
5/∞∞
∞∞
∞/33
33
3/22
22
2:Select an item on the menu screen.
ENTER :Enter a selected item.
5 Try to operate your DVD player by pressing
AUDIO .
When your DVD player turns on or off, you have entered the
correct codes.
If there are more than one code listed for your brand of DVD
player, try each one until the correct one is entered.
Operating Other Manufacturers’Video Equipment
Manufacturers’codes for VCR
Manufacturer Codes
JVC 00*, 26, 27, 28, 29, 58
AIWA 01, 02
BELL & HOWELL 03
BLAUPUNKT 04, 05
CGM 06, 07
EMERSON 08, 10, 11, 12, 64, 65
FISHER 03, 14, 15, 16, 17
FUNAI 01
GE 18, 19, 20
GOLDSTAR 07
GOODMANS 13, 21
GRUNDIG 06, 22
HITACHI 18, 23, 24, 25, 66
LOEWE 07, 21
MAGNAVOX 04, 19, 24
MITSUBISHI 30, 31, 32, 33, 34, 35
NEC 26, 27
NOKIA 03, 36
NORDMENDE 38
ORION 09
PANASONIC 19, 24, 39, 40
PHILIPS 04, 19, 21, 24, 41, 42
PHONOLA 21
RCA/PROSCAN 04, 18, 19, 23, 24, 43, 44,
45
SABA 38, 46
SAMSUNG 45, 47, 59, 61, 62, 63
SANYO 03, 48, 49
SHARP 37, 50
SIEMENS 03, 51
SONY 52, 53, 54
TELEFUNKEN 55, 60
TOSHIBA 43, 44
ZENITH 57
* “00”is the initial setting.
Manufacturers’codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
231
564
897/P
0+1010
EFFECT
TEST
RETURN FM MODE 100+
–SUB WOOFER +
–REAR •R +
–REAR •L +
–CENTER +
MENU
ENTER
Manufacturers’codes for DVD player
Manufacturer Codes
JVC 00, 02
DENON 01
PANASONIC 03
PHILIPS 13
PIONEER 04, 05, 06
RCA 07
SAMSUNG 08
SONY 09
TOSHIBA 10
YAMAHA 11, 12
Manufacturers’codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
EN30-42.RX-7020V[J]f 01.12.27, 3:37 PM39